CS Paper Radar

SentryBus: A Multi-Vantage Observability Model and Validated Instrument for I2C Sensor-Interface Manipulation

Sandesh More, Elton Batista, Karla Daley, Sneha Sudhakaran

cs.CR ·submitted 2026-08-17 19:38 UTC · v1

Abstract

Sensor-driven systems in medical Internet of Things devices, drones, and cyber-physical systems commonly trust a measurement once it reaches the embedded processor. An adversary on the digital interface between sensor and processor can supply a plausible value that correct firmware accepts and reports as ordinary telemetry. The hypothesis is that sensor interface manipulation leaves observable evidence on the acquisition path, that the evidence appears at different vantages depending on attacker position, and that a passive host-side monitor therefore has a measurable boundary beyond which manipulation becomes indistinguishable from legitimate acquisition. SentryBus models acquisition behavior on the I2C sensor bus using transaction timing, read and write sequences, transfer lengths, address behavior, register and FIFO state access, and raw data transitions. The adversary is modeled as an inline interposer, parallel controller, sensor replacement, or compromised host, because a commodity target-only sensor cannot initiate transfers or stretch, reorder, or delay bus transactions. A dual sided testbed captures both busses, host memory, and telemetry, and the detector consumes the host facing bus alone while the remaining vantages serve as ground truth. A physiological instantiation reports three measured results: an inline interposer bounded at 0.842 percent of acquisition service time while preserving acquisition schedule and payload content, clean acquisition stability sustained over 6304 seconds at the telemetry vantage with no clock regression, and a negative result establishing that data-transition features encode session specific signal statistics and do not transfer across capture sessions. Instrument characterization shows that a low-cost analyzer can truncate captures without kernel visible error. Controlled attack trials are still outstanding, so no detection rate is claimed.

Comment
8 pages, 2 figures, 3 tables. Submitted to the IEEE International Conference on Physical Assurance and Inspection of Electronics (PAINE) 2026

Closest papers

Nearest neighbours by meaning across the whole index.

SensorGuard-RV: Sensor-to-Register Data Protection for Resource-Constrained RISC-V Devices

cs.CR cs.AR ·2026-11-05 ·Hamid Noori, Carlton Shepherd
hot direction similarity 0.61
Abstract

Embedded systems rely on sensor measurements that traverse a complex hardware-firmware stack (e.g. peripheral interfaces, communication buses, memory, and drivers) before reaching the applications that use them. At worst, an attacker with access to this path may successfully intercept, overwrite, fabricate, or replay readings. This may cause systems that act on such data, such as flight controllers and industrial processes, to behave incorrectly or unsafely. Existing defences, such as trusted execution environments and trusted I/O paths, still depend on trusted driver software and correctly configured access control, which remain fragile in practice. In response, we present SensorGuard-RV, a hardware-first approach that delivers sensor samples into processor registers without trusting intermediate software, buses, or memory. After configuration, a write-once ownership switch hands the sensor to a fixed-function controller that performs hardware-level authenticated encryption on sensor samples under a key inaccessible to software. We develop a new RISC-V instruction then instructs the CPU to decrypt the sample and writes it to a register only after verifying its tag and rejecting replays, including across resets. We implement SensorGuard-RV on the NEORV32 core with an ADXL362 SPI accelerometer on an Artix-7 FPGA. At 100 MHz, a protected sample reaches a register in 5,191 cycles (51.9 $μ$s), of which the two Ascon authenticated encryption engines account for 30. Because fixed-function acquisition removes per-byte software polling, the protected loop sustains 19,015 transactions/s, 5.3% above a software-driven SPI baseline. The added logic (3,155 LUTs and 2,215 registers; 5.0% and 1.7% of the device) is dominated by the Ascon engine and preserves the 100 MHz clock, while estimated power rises from 118 to 368 mW.

0.29

An Emulation Anchored Digital Twin Testbed for Cyberattack and Defense Analysis in Hospital IT OT Environments

cs.CR ·2026-08-18 ·Prashant Rawat, Ravi Kumar Bairagi, Arunima, Geeta Yadav
similarity 0.58
Abstract

Modern hospitals increasingly rely on integrated Information Technology (IT) and Operational Technology (OT) infrastructures to support critical healthcare services. However, this convergence expands the cybersecurity attack surface and makes safe validation of defensive mechanisms difficult on live systems. Existing testbeds often focus on isolated IT or OT environments and do not capture realistic cross-domain healthcare interactions. This work presents a hospital IT and OT cybersecurity testbed coupled with a digital twin for monitoring, experimentation, and validation of countermeasures. The testbed emulates a central server, Electronic Health Record (EHR) systems, SCADA-based infrastructure, and segmented IT, OT, and DMZ networks. It supports controlled cyberattack execution, software-patch evaluation, and training of RL-based defense agents. The testbed is further extended to a digital twin that models the real-time state of the environment using log and network statistics and enables bidirectional interaction through command execution and container lifecycle orchestration. Modbus/TCP and FHIR/HL7 support realistic communication across healthcare and industrial components. Experimental evaluation shows low computation overhead, with average normalized CPU utilization below 0.4 % per container and most lightweight services operating below 0.01%. OpenPLC Modbus TCP operations achieve a median round-trip latency of 0.901 ms. The testbed also captures a multi-stage SSH-based attack propagating from the DMZ to the IT and PLC networks. The framework provides a foundation for extending the emulated environment toward a hardware-enabled hospital digital twin.

0.31

Seeing is Not Believing: Breaking the Physical-to-Digital Trust Boundary in Robotics

cs.RO cs.CR ·2026-09-08 ·Leming Shen, Shikai Geng, Yuanqing Zheng, Chris Xiaoxuan Lu
similarity 0.58
Abstract

In multi-robot collaboration, task handovers rely on downstream verifiers performing remote attestation, which inspects sensor telemetry to ensure a robot's physical behavior strictly matches its assigned task. But can this telemetry be trusted? We show that it often cannot. In this paper, we uncover a severe vulnerability in Robot Operating System (ROS) 2: by modifying a single environment variable, an adversary can execute a pre-built hook to covertly intercept and inject both telemetry and control signals before they are published. Consequently, adversaries can hijack a robot to perform dangerous tasks while spoofing downstream verifiers with synthesized fake telemetry. Worse still, by exploiting the widespread reliance on third-party Docker containers and auxiliary tools, attackers can distribute compromised packages embedded with these malicious hooks to launch such attacks easily. On a physical Franka Emika robotic arm running Secure ROS 2, our attack injects fabricated telemetry in real time with only around 3 ms of jitter, preserving temporal synchronization and hardware integrity while achieving an 87% success rate even against an AI-based detector. We have responsibly disclosed these findings to the ROS 2 development team. We prepared a demo video available at https://youtu.be/ExeiGqUrnhQ.

0.43

A Resilient Runtime-Verification Fabric for Security Monitoring of Critical Edge-IoT Infrastructure

cs.CR cs.DC ·2026-10-05 ·Nikolaos Kekatos, Marinelio Chintri, Panagiotis Katsaros, Alexios Lekidis, Tom Nianios +3 more
publishedhighly cited similarity 0.55
Abstract · 21 pages, 2 figures. Accepted at the 21st International Conference on Critical Information Infrastructures Security (CRITIS 2026)

Protecting critical infrastructure increasingly depends on continuously verifying large IoT fleets against formal security specifications at runtime. Yet the runtime-verification (RV) pipelines proposed for this task are typically single-host prototypes whose monitors read a shared log file, with no resilience to the failures such deployments incur: a crash or overload silently drops events, clock skew corrupts the ordering metric monitors require, a time-triggered "node has gone silent" property cannot fire when the network itself falls silent, and one slow consumer stalls the pipeline. Each failure is silent: the monitor keeps emitting verdicts over a corrupted view. We present RV-Fabric, a resilient delivery layer that carries the hierarchy over two brokers (MQTT for device ingest, a durable stream broker for backend delivery) and re-establishes five continuity guarantees: durable delivery under crashes, a trusted event order, progress under total silence, consumer isolation and flow control under bounded overload, each an invariant conditioned on broker durability. Above the transport, RV-Fabric makes evidence completeness part of runtime-verification semantics: every verdict carries a status (sound, degraded, incomplete or unavailable) derived from delivery gaps, retention pressure and liveness, so an incomplete stream cannot yield an unqualified all-clear. Under controlled fault injection on a containerised testbed, measured against a fault-free oracle using the real MonPoly engine, the shared-log baseline misses six of seven injected incidents, reporting each as an unqualified all-clear, whereas RV-Fabric preserves all seven; removing a delivery mechanism reintroduces silent loss, removing isolation costs only timeliness. Two published critical-infrastructure datasets, water-SCADA and IoT/IIoT, replay end-to-end.

0.59

Agreement Is Not Assurance: Evidence-Independent Safety Gates for Agentic AI in DER-Rich Distribution Grids

eess.SY ·2026-11-11 ·Qianxue Xia
similarity 0.54
Abstract · 10 pages, 3 figures, 4 tables

Physics-based safety gates for large language model (LLM) agents can approve unsafe actions when the agent and gate rely on the same corrupted measurements or network records. We formulate this shared-evidence failure for voltage-constrained distributed energy resource (DER) export decisions and analyze how nearly critical DER telemetry can bias state estimation while evading residual-based bad-data detection. We propose evidence-independent verification (EIV), which combines advanced metering infrastructure (AMI) voltage readings, measurement selection based on predicted voltage rise, and bounded physical probes. An IEEE 123-bus hidden-truth testbed evaluates 1,654 near-limit requests under telemetry attacks and record errors. For telemetry attacks targeting the nominal gate, an AC-twin gate with bad-data detection approved 95% of unsafe requests, compared with 3.1% for EIV; EIV rejected 22% of safe clean requests. At matched false-rejection settings, direct AMI checks outperformed incorporating the same readings into state estimation. Gate-targeted attacks exposed a vulnerability in telemetry-based response prediction. Command-based prediction removed that route, but targeted attacks on fresh validation cases still produced a 20% unsafe-approval rate under the tested attack pool. LLM agents frequently sought independent evidence voluntarily, but injected instructions and phase-label errors caused unsafe decisions. When offered the EIV checker as a tool, they used it in 93-100% of episodes; mandatory use did not reduce observed violations, which primarily reflected checker errors. These results distinguish enforcement of verification from reliability of the verifier itself.

0.27

Not Discrete Enough: On the Inherent Insecurity of dTPMs for Measured Boot

cs.CR ·2026-08-13 ·Christian Werling, Tahmid Zahin, Jean-Pierre Seifert
top venueposition similarity 0.54
Abstract · Published in: 2025 Annual Computer Security Applications Conference Workshops (ACSAC Workshops)

Measured Boot, a mechanism enabled through Trusted Platform Modules (TPMs), is commonly used for passwordless protection of data-at-rest, aiming to protect data when the device is lost or stolen. Microsoft's standpoint is neutral on which way a TPM should be implemented: Firmware-based TPMs (fTPMs) are viewed as more economical but less secure. Despite the inherent susceptibility to bus sniffing attacks, discrete TPMs (dTPMs) are still seen as the gold standard, as many deliver better on-paper tamper resistance. It is often argued that attacks against the bus can be mitigated by bus encryption and, ideally, mutual authentication between the CPU and TPM. This position paper aims to emphasize another inherent, difficult-to-mitigate attack against dTPMs that was originally shown against a TPM 1.1 over 20 years ago: We demonstrate that even brief physical access to a TPM 2.0 and the ability to boot from an attacker-controlled system enable an attacker to reset and replay arbitrary measurements, thereby allowing an attacker to unseal, for example, a disk encryption key solely protected by the TPM. While there have been attacks against fTPMs, too, we argue that their practical attack surface is fundamentally smaller. Bus protection techniques can be used to protect dTPMs, but only guard against passive attacks. After all, we argue that, from a security standpoint, firmware TPMs, or any TPM internal to the SoC, are superior to discrete (external) ones. Lastly, in order for dTPM-based setups to provide meaningful protection of sealed secrets, configurations must require a user-provided PIN or password along with the Measured Boot configuration.

0.29

Integrity Detection and Characterization of Malicious Injections in RAVEN II

cs.RO ·2026-09-27 ·Xingli Zhang, Diba Afroze, Fei Hu, Xiali Hei
code/data similarity 0.53
Abstract

The increasing adoption of robotic systems in surgery, together with the expanding range of procedures they can support and the growing level of autonomy they provide, has substantially increased the complexity of surgical robots. As these systems integrate more sensors, controllers, communication interfaces, and model-driven control components, their attack surface continues to expand. A compromise of the integrity of a surgical robot can therefore cause unintended robot behavior and potentially threaten patient safety. In this paper, we characterize the detection boundary of malicious injections on RAVEN II using a public dataset that pairs the platform's telemetry with external high-resolution encoder ground truth. We identify three injection points spanning the command and observation paths and evaluate three injection patterns with increasing temporal dispersion. To capture different detection behaviors, we perform detection at two timescales: the window scale and the session scale. Rather than reporting detection rates at an arbitrarily chosen threshold, we quantify, for each injection point and injection pattern, the smallest end-effector deviation that can be resolved while maintaining an alarm rate acceptable for surgical operation. Our results show that detectability is strongly influenced by how the injected deviation is distributed over time. An abrupt step can be detected at deviations well below the 1 mm clinical tolerance, whereas the same overall deviation spread across a window or a session can remain hidden from single-window statistics. The open source code can be found at http://github.com/RAVENIIROS/RAVENIIIntegrity.

0.31

Safety-Aware Zero Trust Enforcement for IoT and Cyber-Physical Systems

cs.CR ·2026-09-23 ·Alessandro Lotto, Alessandro Brighente, Mauro Conti
similarity 0.53
Abstract

Zero Trust (ZT) replaces the implicit trust of perimeter-based security with explicit, continuous, context-aware authorization. This shift is particularly relevant to IoT and cyber-physical systems, whose heterogeneous, long-lived, and remotely connected components make persistent trust untenable. Yet their physical coupling complicates ZT adoption: restricting a suspicious component can reduce cyber exposure while removing telemetry or control capabilities required for operation. Existing work mainly models physical harm caused by attacks, with less attention to consequences introduced by enforcement itself. We introduce Safety-Aware Zero Trust (SA-ZT), which treats restriction-induced physical consequences as policy inputs. We map the NIST ZT tenets to nine IoT/CPS convergence strains, distinguish IoT-amplified challenges from those specific to cyber-physical coupling, and derive corresponding operational requirements. SA-ZT extends the NIST ZT Architecture with a Safety Engine and a Telemetry Broker. The Safety Engine selects among admissible responses by jointly considering residual cyber risk and restriction-induced consequences, while the Telemetry Broker mediates raw telemetry visibility and estimator influence. With command-side enforcement, these entities separate raw visibility, automated influence, and state-changing authority, preserving observations for monitoring while constraining their influence on automated control. An IEEE 30-bus case study under false-data-injection attack illustrates how SA-ZT makes cyber containment, telemetry visibility and influence, physical consequences, and authorization timing explicit, providing an implementable and inspectable representation of cyber-physical enforcement trade-offs.

0.17