CS Paper Radar

Energy-Based Fault Detection and Isolation Framework for Flat Port-Hamiltonian Mechanical Systems

Johnny Garcia, Nicolas Salguero, Naveed Iqbal, Brahim Brahmi, Ramy Rashad

cs.RO eess.SY ·submitted 2026-10-24 13:50 UTC · v1
unusual

Abstract

Fault diagnosis during regulated motion requires informative signals even when feedback attenuates tracking deviations. This paper develops an energy-based diagnostic framework that constructs mechanical port-power residuals without a dedicated dynamic observer. Spectral Hamiltonian Algebraic Power Evaluation (SHAPE) combines port-Hamiltonian variables and differential flatness to generate nominal power references from planned motion for fully actuated mechanical systems with collocated actuation. Subtracting these references from commanded effort multiplied by measured flow yields residuals whose final evaluation requires neither recursive observer updates nor measured-state dynamics calculations. Continuous wavelet transform (CWT) scalograms and a shared-encoder convolutional neural network are used to distinguish nominal operation, actuator loss of effectiveness, anomalous friction, and vibration from complete trajectories. Evaluation uses a simulated six degree of freedom Kinova manipulator under model predictive control and fixed plant-model mismatch, with single faults at a specified joint. Across five training seeds and 3000 held-out test runs, SHAPE-CWT achieves a mean accuracy of 84.69 percent, versus 81.67 percent for torque residuals and 97.17 percent for the generalized momentum observer under common CWT processing. The respective sample standard deviations are 0.70, 0.70, and 0.37 percentage points. These results demonstrate useful fault-type discrimination from algebraic power residuals, while severity-excitation profiles and offline velocity perturbations reveal limits to their diagnostic capability.

Closest papers

Nearest neighbours by meaning across the whole index.

A Harmonic-Regression ARMA model for rotating machinery dynamics identification and fault detection under varying conditions

eess.SP ·2026-09-23 ·Dimitrios M. Bourdalos, John S. Sakellariou, Spilios D. Fassois
published similarity 0.52
Abstract · Accepted for publication in the Proceedings of the International Conference on Noise and Vibration Engineering (ISMA 2026), Leuven, Belgium,…

Fault detection in rotating machinery under varying operating conditions remains a challenging problem. Existing approaches are mainly based either on non-parametric vibration signal representations, parametric deep learning models, or on parametric ARMA-type models. While deep learning approaches often lack transparency and require large training datasets, ARMA-type models rely on the assumption of a purely rational spectrum, which can be restrictive for rotating machinery vibration signals exhibiting mixed spectral characteristics. To address these limitations, a novel Harmonic Regression ARMA (HR-ARMA) model is presented for rotating machinery dynamics identification, which combines an explicit harmonic regression part for representing the dominant deterministic cyclical components with an ARMA part for the remaining broadband stochastic dynamics. Based on this model and within a Multiple Model framework, fault detection is achieved under varying operating conditions. The HR-ARMA modelling performance is validated through simulation and experimental studies on a single-stage gearbox, demonstrating accurate representation of both cyclical and broadband dynamics, improved parsimony and significantly higher fault detection performance compared with conventional ARMA models, achieving at least 98% True Positive Rate at 5% False Positive Rate in the experimental study.

0.39

LaplaceDiag: Fault Diagnosis through Changes in Learned Actuator Effects

cs.AI cs.LG ·2026-11-02 ·Oliver Niggemann
similarity 0.51
Abstract

Identifying faulty components from sensor anomalies is difficult because fault effects can propagate through a plant and different faults can produce similar observations. Detailed component models and labeled fault examples may also be unavailable. We introduce LaplaceDiag, a data-driven method that uses changes in actuator effects to narrow the search for faulty equipment. Actuators act on specific devices and mechanisms, so their changed effects can provide clues to root causes. LaplaceDiag learns a healthy plant model with LaplaceNet, a neural network that operates in Laplace space. It separates nonlinear prediction based on measured history from an explicit matrix that describes how actuator values affect sensor values. Keeping the history predictor fixed allows current actuator effects to be estimated by linear regression without retraining the neural network. Comparison with a healthy reference accounts for estimation uncertainty and normal variation to detect changes and generate actuator-related diagnostic hypotheses. The method supports online and offline diagnosis, providing an intermediate step between anomaly detection and identifying faulty components. We successfully evaluate LaplaceDiag on two datasets.

0.27

Fault detection on manifolds of nonlinear dynamical systems with dual autoencoders

eess.SY ·2026-08-18 ·Bulut Kuşkonmaz, Szymon Greś, Rafał Wiśniewski
similarity 0.51
Abstract

Autoencoders are commonly used for unsupervised data-driven fault detection in nonlinear dynamical systems. Despite their widespread success and often favorable performance compared with traditional approaches, most applications rely on heuristic reconstruction of measured data using features learned from nominal training data, without explicit insight into the underlying nonlinear dynamics. This lack of interpretability limits the extension of autoencoder-based fault detection methods to higher levels of fault diagnosis, e.g., fault localization and quantification, and confines their use largely to application-oriented studies. To address this limitation, we propose a strategy for detecting parametric faults in nonlinear stochastic mechanical systems. A mathematical representation of the output data is developed using Koopman operator theory, which motivates their embedding on a manifold and its subsequent approximation with a two-stage autoencoder. Fault detection is formulated within a hypothesis-testing framework, in which new data are tested for consistency with a neighborhood of the manifold identified from nominal observations. The proposed method is validated through Monte Carlo simulations of a toy mechanical system with two types of nonlinearity and applied to two well-known real benchmarks, where it provides favorable fault-detection performance compared with standard autoencoders.

0.24

Flexibility-Aware Robotic Manipulation: Deformation Estimation, Kinematics, and Control via Distributed Inertial Measurement

cs.RO ·2026-10-30 ·Amir Hossein Barjini, Sadeq Yaqubi, Pauli Mustalahti, Jouni Mattila
similarity 0.50
Abstract

Flexible robot links challenge the rigid-body assumption, making joint measurements alone insufficient for accurate manipulation. This paper introduces a flexibility-aware manipulation framework that connects structural dynamics directly to sensing, kinematics, and control. Instead of prescribing a dense inertial measurement unit (IMU) network, the dominant vibration modes of each flexible link are first identified from response-convergence and excitation-bandwidth criteria. Under a full-rank modal observability condition, $m$ retained modes require only $m$ independent slope measurements and one reference IMU, defining the minimum observable IMU configuration. The resulting measurements are used to reconstruct the continuous link deformation, which is then incorporated into flexibility-aware forward kinematics and a deformation-informed partial differential equation-based controller. Experiments on hydraulic single- and double-link manipulators evaluate the framework. On the long-reach double-link platform, the proposed kinematics achieves end-effector root mean square errors of $0.0107$~m, $0.0194$~m, and $0.0102$~rad while using fewer sensors than the piecewise-rigid method. Closed-loop reaching experiments further demonstrate real-time integration of IMU-estimated joint states and reconstructed deformation into the proposed controller. The results show that dominant modal information can determine sensing requirements and enable real-time flexibility-aware robotic manipulation.

0.34

Lightweight Time-Frequency Vibration Sensing for Consumer Device Condition Monitoring

eess.SP cs.LG ·2026-10-09 ·Po-Heng Chou, Jen-Yu Chiu, Chun-Yu Yeh, Wei-Lung Mao, Walid Saad
benchmark similarity 0.49
Abstract · 6 pages, 3 figures, and 4 tables. Submitted to the 2027 IEEE International Conference on Consumer Electronics (ICCE 2027)

Consumer rotating devices, including washing machines, air conditioners, electric fans, robotic vacuum cleaners, and home fitness equipment, increasingly rely on vibration sensing for intelligent condition monitoring and predictive maintenance. Ensuring reliable operation in these resource-constrained appliances requires efficient, lightweight artificial intelligence (AI) solutions capable of processing non-stationary signals under real-world operational interference. This paper proposes a lightweight AI-assisted vibration sensing framework that employs continuous wavelet transform (CWT) and Hilbert-Huang transform (HHT) to convert one-dimensional (1-D) vibration time-series signals into two-dimensional (2-D) time-frequency representations. These representations are subsequently analyzed using lightweight deep learning architectures, specifically MobileNetV3-Small, ConvNeXt-Tiny, and the You Only Look Once version 11 classification model (YOLOv11-cls). Public bearing benchmark datasets, including Case Western Reserve University (CWRU), Paderborn University (PU), and Intelligent Maintenance Systems (IMS), are utilized as representative rotating components to investigate model generalization. The proposed framework is designed with eventual embedded deployment in consumer electronics in mind. Experimental results demonstrate that CWT combined with YOLOv11-cls achieves high diagnostic accuracy, while MobileNetV3-Small provides an attractive low-latency alternative for computationally constrained edge platforms. Conventional random splitting is also compared with dataset-specific structured isolation. The results highlight the importance of avoiding data leakage and quantify tradeoffs in classification accuracy, parameter count, floating-point operations (FLOPs), model footprint, preprocessing cost, and central processing unit (CPU) inference latency.

0.23

Physical-Variable-Informed Deep Learning for Robust Diagnosis in Industrial Fluid Transport Systems

cs.LG cs.AI ·2026-10-20 ·Yu Sha, Junqi Tao, Dixin Zhou, Horst Stoecker, Domagoj Vnucec +2 more
similarity 0.49
Abstract · 29 pages, 5 figures

Industrial fluid transport systems are monitored through heterogeneous sensing streams, but robust fault diagnosis remains difficult because response signals vary with operating conditions and differ from physical variables in sampling rate, observation duration and data granularity. To address these challenges, we propose a physical-variable-informed deep learning framework (PhyNet) for robust fault diagnosis under real-world sampling heterogeneity. PhyNet treats physical variables as global operating constraints and response signals as local diagnostic evidence. Its physical-to-response cross-attention mechanism connects sequence-level physical-variable tokens with a learnable global response token, enabling interaction without strict temporal alignment. Across four benchmarks, including three real-world cavitation datasets and one public two-phase-flow dataset, PhyNet achieves the best performance across all evaluated metrics. Class-wise analyses, together with attention and masking analyses, show improved discrimination of ambiguous states and indicate that physical variables meaningfully constrain local response interpretation. These findings demonstrate a deployment-oriented approach to robust diagnosis in heterogeneous industrial environments.

0.33

Spectrogram-Based CNN Autoencoder for One-Class Anomaly Detection in Machining Vibration Signals

cs.LG ·2026-11-07 ·Sebastian Zeleny, Christian Gawron
published similarity 0.48
Abstract · 29 pages, 14 figures

This work presents a one-class anomaly detection framework for vibration-based condition monitoring in machining processes using a convolutional neural network autoencoder. Three-axis vibration signals acquired during industrial broaching are transformed into time--frequency spectrograms and combined into a compact three-channel representation, enabling convolutional feature learning on multivariate time-series data. The autoencoder is trained exclusively on normal process data and detects anomalous strokes based on reconstruction errors. Labeled validation data are used for threshold calibration and an independent test set is reserved for final performance evaluation. To improve sensitivity to short-lived process instabilities such as chatter, a localized residual-based metric termed Segmented Vertical Error (SVE) is introduced. Experimental results on approximately 10{,}000 broaching strokes show a clear separation between normal and anomalous process conditions under strong class imbalance. The processing pipeline is additionally evaluated on an external public turning dataset as a proof of concept, indicating preliminary applicability beyond the original broaching setup. The results suggest that spectrogram-based autoencoder models can provide a practical and scalable basis for one-class anomaly detection in industrial vibration monitoring.

0.34

Port-Hamiltonian Koopman Operator Synthesis for Mechanical Systems

cs.RO eess.SY ·2026-09-15 ·Rajpal Singh, Aditya Singh, Jishnu Keshavan
similarity 0.48
Abstract

Finite-dimensional Koopman models enable efficient linear prediction and control of nonlinear robotic systems. However, models learned purely from trajectory data may violate the energetic structure of the underlying mechanics, producing predictions that exhibit artificial energy growth and diverge under recursive propagation. This work presents a structure-preserving Koopman framework for Euler-Lagrange systems built on generalized-momentum coordinates. The momentum transformation exposes the mechanical actuation as a known, state-independent port, which is preserved explicitly in the lifted dynamics. A structure-constrained neural architecture is developed to jointly learn the lifting functions and a port-Hamiltonian Koopman generator, rendering the learned dynamics passive by construction rather than through penalty terms or post-hoc projection. A Cayley-midpoint discretization further preserves the corresponding storage-dissipation balance exactly in discrete time. These properties are established analytically by deriving the discrete storage balance and associated stability guarantees of the learned predictor. Simulation and experimental studies demonstrate improved prediction accuracy, data efficiency, and closed-loop tracking over Koopman baselines, with increasing gains for higher-dimensional systems.

0.23