CS Paper Radar

Effect of Twisted-Yarn Architecture on Pressure and Proximity Sensing Characteristics of Textile Capacitive Sensors for Robotic Skin

Ishtia Zahir, Eslam Saleh, Maryam Rezayati, Güunter Grabher, Gaffar Hossain

cs.RO physics.ins-det ·submitted 2026-08-14 15:48 UTC · v1

Abstract

Textile-integrated capacitive sensors offer flexible and conformable tactile sensing for wearable electronics and human-robot interaction; however, the influence of yarn-level architecture on capacitive transduction characteristics remains insufficiently quantified. This work presents a textile capacitive sensing platform based on silver-coated yarns coated with polydimethylsiloxane and assembled into one-, two-, and four-layer twisted configurations. The influence of effective electrode overlap area and inter-fiber separation on the capacitive response is systematically investigated, enabling architecture-dependent tuning of pressure and proximity sensing characteristics. Pressure was calculated using the localized single-fiber contact area, corresponding to stresses of 0.4-3.9 MPa. Increasing the layer number improved mechanical strength and sensing performance: elongation at break increased from 37.5% to 62.5% and 85.0%, while the maximum load increased from 23.3 to 42.7 and 89.7 N. Sensitivity increased with layer number and frequency, reaching 0.1331 MPa$^{-1}$ for the four-layer sensor at 100 kHz. The four-layer configuration also exhibited low hysteresis, minimal thermal drift from 25 to 90 $^\circ$C, and stable operation over 15,000 cycles. Proximity detection ranges of 60, 50, and 40 mm were obtained for the one-, two-, and four-layer sensors, respectively, revealing an architecture-dependent sensitivity-range trade-off. A 4$\times$4 textile sensing array enabled spatial contact mapping, while robotic-arm integration demonstrated real-time touch and proximity detection with an end-to-end robotic system latency (from detection to robot reaction) of 403 ms. The results establish yarn architecture as a tunable design parameter governing the measurement characteristics of textile-integrated capacitive sensing systems.

Comment
10 pages. Submitted to IEEE Transactions on Instrumentation and Measurement

Closest papers

Nearest neighbours by meaning across the whole index.

SoTa: Soft Tactile Skins for Dexterous Manipulation

cs.RO cs.LG ·2026-10-01 ·Jingyun Yang, Baiyu Shi, Timothy Yu, Haitian Liu, Alberta Longhini +4 more
code/data similarity 0.59
Abstract · The first three authors contributed equally. Project website: https://sota-skin.github.io

A growing body of work suggests that tactile sensing gives robot policies contact information that complements vision in dexterous manipulation. However, visuo-tactile robot data remains scarce: dexterous demonstrations require teleoperating robots, which limits dataset scale. Human demonstrations are far cheaper to collect and offer a path to scale this data, but only if human and robot hands carry tactile sensors with corresponding signals. This requires sensors that conform to different hand geometries, cover the full hand, and share a common layout across embodiments. We present SoTa, a low-cost capacitive tactile skin that provides full-hand coverage on humans and robots while preserving a shared layout of 202 taxels across corresponding finger and palm regions. Our multilayer design with fabric electrodes enables in-house fabrication of thin, soft skins with customizable geometry for under $10 in materials per skin. The sensor retains over 97% of its initial response span after 10,000 loading-unloading cycles with traces retaining continuity through 1,280 tight-fist folding cycles. The shared taxel layout supports human-robot co-training with a common tactile encoder and no learned cross-sensor mapping. Across three contact-rich manipulation tasks, tactile observations improve in-distribution success over vision-only policies. With a fixed robot demonstration budget, adding human demonstrations more than doubles mean success across eight evaluation conditions, from 22.8% to 45.9%, improving success in all five out-of-distribution conditions. We plan to open-source the resources needed to fabricate and operate these skins.

0.20

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.58
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

Proximity3D: Shape from Capacitive Proximity on Sensing Manifold

cs.CV cs.CGcs.GRcs.RO ·2026-08-31 ·Hao Chen, Chenming Wu, Chun Ping Lam, Xiangjia Chen, Guoxin Fang +4 more
top venue similarity 0.57
Abstract

Most shape reconstruction methods assume measurements defined over planar sensing domains, such as RGB images or depth maps. In this paper, we use a curved capacitive textile as a shape sensor, treating its surface as a non-planar sensing manifold. Each scan is represented as a capacitive proximity field on this manifold, induced by the interaction between the curved electrode layout and nearby object geometry. We introduce a multi-view feedforward reconstruction model that aggregates these fields across known sensor views and recovers the observed object shape. Simulated and physical experiments demonstrate robust reconstruction from capacitive proximity signals acquired on curved sensing surfaces, pointing toward a new route to robotic near-field geometric awareness via embodied sensing.

0.43

A Wearable Pneumatic Device for Continuous, Closed-Loop, Bidirectional Tactile Interaction

cs.RO ·2026-09-01 ·Cosima du Pasquier, Aliyah Smith, Serin Huber, Joshua Phelps, Ilana A. Cohen +3 more
similarity 0.57
Abstract

We present a system of two wearable pneumatic haptic devices that supports continuous, closed-loop, bidirectional tactile interaction at perceptually relevant force and temporal scales. A single device can contain up to twelve pressure sensing channels connected to textile-based pneumatic pouches. Each channel in a device can be used as a sensor, an actuator, or both. As an actuator with integrated sensing, the channel generates stable skin indentation through local closed-loop control. As a sensor, a channel can be mounted (or worn) on any surface, including on a robot gripper or on the human body, and used to measure touch interactions with the environment or a human user. A distributed architecture supports sustained pressure output, rapid dynamic response, and wireless pairing of identical devices in a system to transmit and reproduce tactile pressure signals in real time. Device-level characterization demonstrates force bandwidth exceeding 30 Hz, rapid and well-damped step responses, and extended pressure retention compared to prior compact pneumatic platforms. Human studies show that pressure-based fingertip feedback enables discrimination of force and stiffness, improves teleoperated manipulation by reducing applied pressures by up to 23.1% and task duration by up to 27.4%, and lowers subjective mental workload by 18.8%, particularly under visually constrained conditions. By unifying tactile sensing and haptic feedback within a single pneumatic modality, the device provides a practical foundation for bidirectional touch interaction in teleoperation.

0.14

A robust single-sensing-element tactile sensor for concurrent pressure and tackiness detection with real-time signal decoupling capability

cs.RO cond-mat.mtrl-sci ·2026-09-29 ·Ying Yang, Mingwei Gu, Jia-Sen Xie, Xingyu Ma, Yan-Na Lu +6 more
similarity 0.56
Abstract

Integrating tackiness sensation into the artificial skin of humanoid robots significantly enhances their cognitive and operational capabilities. However existing tactile sensors face challenges in decoupling of the multimodal signal and stability. Here we present a surface-soft tactile sensor that incorporates a Hall effect sensor and a soft magnetic composite within a robust elastic framework. The sensor surface indents under pressure and bulges prominently when retracted from sticky surfaces dynamically altering the Hall sensor-magnet distance. This generates whole-process-traceable and baseline-separated signals enabling real-time differentiation between pressure and pull-off force. This single-sensing-element design facilitates bimodal sensing at the same contact spot while eliminate stress cross-talk enhancing both accuracy and sensitivity. The fusion of a robust framework and magneto-mechanical sensing mechanism equips the sensor with exceptional reliability and excellent signal baseline stability. This tactile sensor holds substantial potential for advancing robotic capabilities in evaluating adhesive properties monitoring rubber aging precisely handling lightweight objects and cognizing natural objects surface characteristics.

0.20

Non-Imaging Optical Tactile Sensors for Robotics: Transduction Principles, System Integration, and Robotic Applications

cs.RO ·2026-11-16 ·Hao Wu, Yu Feng, Haotian Guo, Huichan Zhao, Changsheng Wu +1 more
similarity 0.55
Abstract · 35 pages, 9 figures

Non-imaging optical tactile sensors encode contact through changes in optical intensity, wavelength, spectra, or photon counts, offering diverse architectures for robotic touch. Their usefulness depends on whether contact variables can be reliably distinguished from coupled mechanical and environmental effects, and whether the resulting information can be delivered in time to guide action. This review develops a unified framework linking mechanical load transmission, optical encoding, readout, and tactile inference to robotic task requirements. It examines reflective and waveguide-based devices, micro/nanofibers, fiber gratings, interferometric and resonant structures, and mechanoluminescent composites. Three considerations emerge across these approaches. First, high optical sensitivity supports accurate tactile estimation only when target variables remain identifiable under the relevant contact and calibration conditions. Second, spatial coverage and feedback timing must be assessed at the system level, accounting for multiplexing, acquisition, demodulation, and inference. Third, device characterization, offline recognition, and closed-loop robotic performance provide distinct levels of evidence and require different evaluation criteria. Representative studies illustrate how these considerations shape force estimation, contact localization, slip correction and distributed interaction. This review concludes with priorities for calibration transfer, reliable interfaces, scalable readout, and task-based validation, providing a basis for selecting and developing non-imaging optical tactile architectures for robotics.

0.16

Tactus: Tactile & Pose Sensing Glove for Natural Dexterity Data Collection

cs.RO cs.AIcs.ARcs.LG ·2026-10-29 ·Li Guan, Rachael Granberry, Sahar Aseeri, Sahar Rostami, Taylor Niehues +99 more
similarity 0.54
Abstract · 9 pages

Collecting naturalistic human manipulation demonstrations with accurate contact force and hand pose is essential for robot dexterous manipulation policy and foundational world model learning - yet no existing wearable platform provides both calibrated fingertip force sensing and occlusion-resilient hand tracking in a form factor that preserves natural manipulation behavior. We present Tactus, a textile-integrated sensing glove that co-optimizes three design pillars: (1) a thin, conformal 3D-knit form factor (1.5 mm fingertip stackup) designed to minimize interference with natural manipulation, (2) strategically placed capacitive tactile sensors at manipulation-relevant regions informed by empirical contact studies, and (3) IMU-fused pose tracking that maintains accuracy through the hand-object occlusions where manipulation data is most valuable. Tactus includes a documented calibration pipeline for cross-glove consistency and per-session calibration for subject-dependent correction. To enable objective comparison, we introduce standardized benchmarking protocols for tactile force regression and hand pose estimation, and apply them to Tactus and two commercially available tactile gloves - to our knowledge the first quantitative cross-platform evaluation of this kind. Tactus resolves a minimum detectable force of 0.59 N at 95% confidence, 1.6 - 2.7x lower than the commercial baselines, and with 0.87 cross-participant consistency, while our pose tracking sustains 11.0 mm fingertip keypoint relative error during manipulation, when occlusion is heaviest. We show that these combined signals support object property estimation, slip detection, and representative recording of hand-object interaction - yielding demonstration data with the fidelity required for contact-aware manipulation policies and world models.

0.21

Layered e-skin for Shear Sensing

cs.RO ·2026-09-18 ·Qingzheng Cong, Alexis W. M. Devillard, Abu Bakar Dawood, Xinxin Zhang, Wen Fan +5 more
similarity 0.53
Abstract · 8 pages, 5 figures. Submitted to IEEE Sensors Journal

This paper presents a stacked two-layer force-sensing resistor (FSR) array designed for robotic fingertips that combines high-resolution pressure mapping with shear-force estimation. A compliant lattice elastomer spacer converts shear loading into a measurable inter-layer displacement, producing relative center-of-pressure (CoP) shifts between layers. A physics-based moment balance links inter-layer CoP displacement to shear force, while an end-to-end CNN--GRU model captures nonlinear effects from load-dependent compression and contact redistribution. This model, with both layers as input, achieves coefficients of determination $R^2 = 0.914$ for $F_x$ and $R^2 = 0.944$ for $F_y$, consistently outperforming single-layer baselines for shear-force estimation. Robotic manipulation experiments show that, for contact-motion tracking, the deep layer tracks the translation and rotation imposed by the robot arm, whereas the superficial layer tracks the slip at the contact surface. Transient changes in the difference between the total pressure responses of the two layers provide the best slip-event detection performance among the tested cues. These results demonstrate that two-layer FSR arrays can provide three-axis force estimation, contact-motion tracking, and slip-event detection beyond conventional normal-force sensing.

0.32