CS Paper Radar

Layered e-skin for Shear Sensing

Qingzheng Cong, Alexis W. M. Devillard, Abu Bakar Dawood, Xinxin Zhang, Wen Fan, Neri Niccolò Dei, Cem Suulker, Kaspar Althoefer, Etienne Burdet, Dandan Zhang

cs.RO ·submitted 2026-09-18 18:59 UTC · v1

Abstract

This paper presents a stacked two-layer force-sensing resistor (FSR) array designed for robotic fingertips that combines high-resolution pressure mapping with shear-force estimation. A compliant lattice elastomer spacer converts shear loading into a measurable inter-layer displacement, producing relative center-of-pressure (CoP) shifts between layers. A physics-based moment balance links inter-layer CoP displacement to shear force, while an end-to-end CNN--GRU model captures nonlinear effects from load-dependent compression and contact redistribution. This model, with both layers as input, achieves coefficients of determination $R^2 = 0.914$ for $F_x$ and $R^2 = 0.944$ for $F_y$, consistently outperforming single-layer baselines for shear-force estimation. Robotic manipulation experiments show that, for contact-motion tracking, the deep layer tracks the translation and rotation imposed by the robot arm, whereas the superficial layer tracks the slip at the contact surface. Transient changes in the difference between the total pressure responses of the two layers provide the best slip-event detection performance among the tested cues. These results demonstrate that two-layer FSR arrays can provide three-axis force estimation, contact-motion tracking, and slip-event detection beyond conventional normal-force sensing.

Comment
8 pages, 5 figures. Submitted to IEEE Sensors Journal

Closest papers

Nearest neighbours by meaning across the whole index.

VecTile: A Low-Cost Flexible Tactile Array for 3-DoF Force Sensing

cs.RO ·2026-10-22 ·Jian Hou, Xin Zhou, Adam J. Spiers
similarity 0.68
Abstract · 8 pages, 8 figures. Submitted to IEEE International Conference on Robotics and Automation (ICRA) 2027

Tactile sensing provides robots with contact information difficult to obtain from vision alone. Shear force is particularly important for understanding tangential contact, guiding corrective motions, and maintaining grasp stability, yet flexible and low-cost tactile arrays often measure only normal force. We introduce VecTile, a low-cost, 6 mm thin, flexible tactile array capable of three-axis force sensing. VecTile combines a piezoresistive layer with passive silicone nubs that convert normal and shear forces into distinguishable pressure patterns. The sensor can be fabricated in-house without specialized equipment. The complete system costs less than 35 USD for a 4x4 array. We validate the sensing mechanism through finite element analysis and hardware experiments. In controlled single-taxel tests over 1-5 N normal force and up to 1.5 N shear force, VecTile achieves root-mean-square errors of 0.39 N and 0.16 N for normal and shear forces. A VecTile calibrated while flat retains accuracy when curved, while a five-minute manual calibration is sufficient for practical use. Two applications demonstrate its utility. First, shear readings are sensitive enough to stop a sharp scalpel from puncturing a balloon after contact. Second, the sensor substantially improves Diffusion Policy-guided power-plug insertion. All designs and code will be released upon paper acceptance. Project website: https://jiannnh.github.io/VecTile/.

0.20

PanoTac: A Dense Three-Axis Tactile Sensor for Robust Touch-Centric Manipulation

cs.RO cs.AIcs.LG ·2026-11-02 ·Binglin, Wang, Xiaole, Jiang, Zicheng Teng +5 more
code/data similarity 0.65
Abstract · Project page: https://panotac.github.io

Contact-rich manipulation benefits from tactile feedback that captures both detailed contact geometry and interaction forces. When scooping grains, contact patterns help infer spoon orientation, while resistance transmitted through the grasp guides motion. To provide these complementary sensing capabilities, we present PanoTac, a low-cost, compliant tactile fingertip designed for dense three-axis tactile sensing. Each fingertip provides a $12 \times 32 \times 3$ tactile representation, with one normal ($z$) and two shear ($x$, $y$) response components at each taxel. The sensor operates at 60 Hz and costs less than $50 per fingertip. Sensor characterization quantifies response repeatability and consistency across sensor instances and contact locations. We integrate PanoTac into a robotic system with a visuo-tactile pipeline. Across test-tube preparation, grain scooping, and salt pouring, the resulting policies outperform vision-only baselines by an average of 46.7 percentage points. Ablations show that removing either spatial contact information or shear feedback reduces overall performance across the task suite. Our project page is available at https://panotac.github.io.

0.19

Single-View RGB-D Force--Deformation Estimation for Robotic Manipulation of Elasto-Plastic Materials

cs.RO ·2026-11-11 ·Dezhi Sun, Marijn van Hilten, Kenan Niu
published similarity 0.64
Abstract · 7 pages. Accepted at IEEE ROBIO 2026

Persistent deformation complicates elasto-plastic manipulation by coupling physical interaction with spatially distributed shape changes. We investigate the force--deformation relationship using a standard robot, a single eye-in-hand RGB-D camera, and intrinsic force estimates. A 7-DoF Franka Emika FR3 performs normal indentations while an Intel RealSense L515 captures pre- and post-contact surfaces. Point-cloud processing localizes deformation and estimates displaced volume. Force--volume characterization includes 27 measurements over nine force levels. A compact multilayer perceptron (MLP), trained on 52 force--volume pairs at four levels, achieves a held-out RMSE of 1.857 N and $R^2=0.440$. A separate comparison shows lower error for a quadratic model at 16 N and for the MLP at 19 and 23.5 N. An eight-step experiment at 4 N per interaction demonstrates cumulative deformation localization from the second indentation onward. These results establish a practical measurement basis for deformation-aware manipulation using intrinsic force estimates and single-view geometry.

0.22

Tactile Reconstruction of Contact Task Frames and Forces for Hybrid Force/Motion Control

cs.RO ·2026-10-07 ·Antonio Rapuano, Simone Orelli, Barbara Bazzana, Antonio Franchi, Alessandro De Luca
similarity 0.64
Abstract · 14 pages, 9 figures, 7 tables. Video: https://youtube.com/playlist?list=PLejKMZmW8AvI. Dataset: https://doi.org/10.5281/zenodo.23209032

Hybrid force/motion control requires knowledge of the interaction force and of a task frame defining the force- and motion-controlled directions. These quantities are usually obtained from force/torque sensing or model-based residuals, often assuming also a nominal environment model. This work addresses the online estimation of the contact force and a possibly time-varying task frame using only soft optical tactile sensing, under the assumption of locally planar contact with a negligible contact moment. The proposed method maps a single image of the deformed elastomer of a soft optical tactile sensor to observable contact variables: indentation depth, two surface-to-sensor tilt angles, and 3D contact force, each with a per-sample uncertainty estimate. The mapping is learned through a self-labeling acquisition procedure, in which a manipulator imposes controlled contacts while an auxiliary Force/Torque sensor is used offline to provide ground-truth labels. The tactile measurement is then fused with robot proprioceptive data in an Extended Kalman Filter, producing a continuously updated estimate of the contact task frame and of the interaction force. Control experiments with a DigiTac sensor mounted on a UR10 manipulator demonstrate closed-loop contact force regulation against a flat rigid board in linear and angular motion by a human operator, with touch as the only exteroceptive feedback.

0.23

Tactile Perception through Fluid-Solid Interaction

cs.RO cond-mat.soft ·2026-09-29 ·Arman Goshtasbi, Minke Berghuis, Aida Parvaresh, Saravana Prashanth Murali Babu, Robert W. Style +1 more
top venue similarity 0.62
Abstract

Soft tactile sensors elevate robotic touch through enhanced flexibility and adaptability, yet most existing designs depend on embedded electronics that are susceptible to interference and environmental limitations. In this work, we leverage fluid-solid interactions to develop a class of soft tactile sensors that operate entirely without electronics at the sensing site. The sensor comprises a fluid-filled elastomeric channel connected to only two external pressure sensors. Touching different regions of the elastomeric surface displaces the viscous fluid, producing distinct pressure patterns that encode both touch position and force. These signals are decoded through a machine learning framework that integrates feature extraction, soft clustering, and adaptive neuro-fuzzy inference to achieve accurate localization and force estimation. We validate this concept through single-point touch localization and force estimation in a linear (1D) sensor and extend the same sensing principle to 2D tactile mapping by routing the channel across the surface using space-filling curves, while maintaining the same minimal hardware setup. This simple approach remains effective in environments where conventional electronic sensors often fail, such as underwater or in the presence of magnetic interference.

0.56

TacGooseBumps (TacGB): Retrofitting Normal-Only Tactile Sensors with Shear Encoding for Learning Contact-Rich Manipulation

cs.RO ·2026-09-27 ·Wenjie Li, Binyu Yang, Yuxin Chen, Ambrose Wang, Masayoshi Tomizuka
hot direction similarity 0.62
Abstract · 9 pages, 8 figures. Wenjie Li and Binyu Yang contributed equally. v2: added project website, updated references, and improved HTML rendering…

Contact-rich policies often fail because distinct physical states look alike yet require different actions. Cameras may not reveal whether a connector is aligned or fully seated, while many normal-only tactile sensors can miss the tangential interactions perpendicular to the grasping direction that distinguish these states. We ask whether a learning policy needs calibrated shear measurements, or only a repeatable observation that separates shear-dependent contact states. We introduce TacGooseBumps (TacGB), a passive domed film that mechanically encodes tangential loading as pattern changes in an existing sensor's pressure map. Tangential loading tilts each dome and redistributes pressure across its footprint; an end-to-end policy consumes the resulting maps without added electronics, force reconstruction, or taxel-level dome alignment. Across four imitation-learning tasks and two data-collection pipelines, TacGB improves goal attainment, efficiency, and contact quality: insertion success increases by up to 36 percentage points, and successful insertions are completed faster, while fragile-object placement becomes gentler and drawing becomes more continuous and straight. Signal, stage-wise, failure-mode, and trajectory analyses link these gains to contact regimes in which task-relevant tangential interactions are poorly resolved by vision and normal pressure alone. Together, these results show that shear need not be measured metrically to benefit robot learning; it can instead be mechanically encoded without changing the underlying tactile sensor or the policy's pressure-map input format.

0.36

Control Architecture for Safe Grasping of Fragile Objects Using a Coarse Position-Controlled Gripper

cs.RO ·2026-09-11 ·Marko Pavlic, Moritz Geier, Timo Markert, Darius Burschka
published similarity 0.60
Abstract · Accepted for IEEE IROS 2026 publication

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

0.28

History-Aware Force Sensing and Tunable Stiffness in a Pneumatic Kresling Origami Cell

cs.RO ·2026-11-01 ·Hengyi Zhou, Jiaqi Wang, Yilin Ma, Dezhong Tong, Xiaonan Huang
similarity 0.60
Abstract

Mechanical hysteresis and pneumatic loading complicate contact force estimation from deformation measurements in soft robots. This work presents a 3D-printed polyether block amide (PEBA) Kresling cell with magnetic angular sensing that supports three operating modes: force sensing at zero gauge pressure, force sensing with tunable stiffness under gauge positive pressure, and self-sensing actuation under negative gauge pressure. A multiscale gated recurrent unit (GRU) network estimates contact force from angular histories to account for the the combined effects of geometric deformation and material response. At zero gauge pressure, the model achieves a test RMSE of 0.76~N. Positive gauge pressure approximately doubles the average axial loading stiffness at +20~kPa over the first 3~mm of compression, while pressure-specific models maintain RMSEs below 0.93~N. Under negative gauge pressure, an energy-based compensation model enables contact force estimation using the the model trained at zero gauge pressure, achieving RMSEs of 1.66--2.10~N under quasi-static conditions. These results demonstrate a compact approach to combining force feedback, tunable axial stiffness, and self-sensing actuation in soft origami systems.

0.36