CS Paper Radar

History-Aware Force Sensing and Tunable Stiffness in a Pneumatic Kresling Origami Cell

Hengyi Zhou, Jiaqi Wang, Yilin Ma, Dezhong Tong, Xiaonan Huang

cs.RO ·submitted 2026-11-01 19:18 UTC · v1

Abstract

Mechanical hysteresis and pneumatic loading complicate contact force estimation from deformation measurements in soft robots. This work presents a 3D-printed polyether block amide (PEBA) Kresling cell with magnetic angular sensing that supports three operating modes: force sensing at zero gauge pressure, force sensing with tunable stiffness under gauge positive pressure, and self-sensing actuation under negative gauge pressure. A multiscale gated recurrent unit (GRU) network estimates contact force from angular histories to account for the the combined effects of geometric deformation and material response. At zero gauge pressure, the model achieves a test RMSE of 0.76~N. Positive gauge pressure approximately doubles the average axial loading stiffness at +20~kPa over the first 3~mm of compression, while pressure-specific models maintain RMSEs below 0.93~N. Under negative gauge pressure, an energy-based compensation model enables contact force estimation using the the model trained at zero gauge pressure, achieving RMSEs of 1.66--2.10~N under quasi-static conditions. These results demonstrate a compact approach to combining force feedback, tunable axial stiffness, and self-sensing actuation in soft origami systems.

Closest papers

Nearest neighbours by meaning across the whole index.

A Monolithic Force-Proprioception Soft Acutuator Enabled by Single-Material 3D printing

cs.RO ·2026-09-21 ·Nan Huang, Lele Liu, Junfeng Lu, Yipan Zhu, Jiansheng Dai +1 more
similarity 0.60
Abstract

Pneumatic proprioceptive actuators integrate actuation and sensing for soft robots that attract interest due to functional potential. Existing approaches often suffer from assembly errors or stress concentrations caused by heterogeneous materials. In this work, we propose the Monolithic Force-Proprioception Soft (MFPS) design and fabrication method that integrates an Asymmetric Origami Bending (AOB) chamber and a Force-Proprioception Soft (FPS) sensor with single material through one-step Fused Deposition Modeling (FDM) fabrication. Based on the resistance response to strain of conductive thermoplastic polyurethane (TPU), we design and analyze the structure of the FPS sensor, and conduct parametric analysis on the sensing characteristics. The FDM fabrication parameters of the MFPS actuator are analyzed, followed by actuator fabrication and characterization of the actuation and proprioception performance. Experimental results show that the MFPS actuator achieves a bending angle of 40°, an output force of 12.5 N, and a resistance change of 26.9% as the applied external force increased from 0 to 45 N. A two-finger force-proprioception gripper is developed based on the MFPS actuator. The grasping and force-proprioception capabilities are experimentally validated, proving that the MFPS design method provides a new approach for the development of self-sensing actuators.

0.20

Layered e-skin for Shear Sensing

cs.RO ·2026-09-18 ·Qingzheng Cong, Alexis W. M. Devillard, Abu Bakar Dawood, Xinxin Zhang, Wen Fan +5 more
similarity 0.60
Abstract · 8 pages, 5 figures. Submitted to IEEE Sensors Journal

This paper presents a stacked two-layer force-sensing resistor (FSR) array designed for robotic fingertips that combines high-resolution pressure mapping with shear-force estimation. A compliant lattice elastomer spacer converts shear loading into a measurable inter-layer displacement, producing relative center-of-pressure (CoP) shifts between layers. A physics-based moment balance links inter-layer CoP displacement to shear force, while an end-to-end CNN--GRU model captures nonlinear effects from load-dependent compression and contact redistribution. This model, with both layers as input, achieves coefficients of determination $R^2 = 0.914$ for $F_x$ and $R^2 = 0.944$ for $F_y$, consistently outperforming single-layer baselines for shear-force estimation. Robotic manipulation experiments show that, for contact-motion tracking, the deep layer tracks the translation and rotation imposed by the robot arm, whereas the superficial layer tracks the slip at the contact surface. Transient changes in the difference between the total pressure responses of the two layers provide the best slip-event detection performance among the tested cues. These results demonstrate that two-layer FSR arrays can provide three-axis force estimation, contact-motion tracking, and slip-event detection beyond conventional normal-force sensing.

0.32

Towards Effective Physical Reservoir Computing with a Pneumatic Soft Robot

cs.RO ·2026-09-02 ·Jeevan Hebbal Manjunath, Jun Wang, Suyi Li, Wenlong Zhang
publishedbenchmark similarity 0.59
Abstract · 6 pages; 5 figures, accepted for 2026 Modeling, Estimation, and Control Conference (MECC)

Physical reservoir computing (PRC) refers to the use of a physical dynamical system as a computational resource for tasks such as state estimation and control, but there has been a lack of formal study of design rules towards more effective design of such physical reservoirs. Using a pneumatic soft arm with a five-pouch sensing column, this work studies how the pouch interconnection topology, robot stiffness, and the number of instrumented sensors affect bending-angle estimation performance. Across 36 matched trials spanning waveform, baseline pressure of the sensing column, and actuation range, all designs are evaluated under the same-time bending-angle estimation benchmark using 0.2 s of pressure history and a fixed ridge estimator. Our analysis of the experimental results leads to three design guidelines. First, independently sealed pouches preserve a much richer observable state than a shared manifold. Second, increasing the baseline pressure of the sensing column makes the pouch responses more redundant and increases estimation error most strongly in the coupled topology. Third, in the sealed topology, two strategically placed sensors already recover most of the attainable benefit, three capture essentially all of it, and additional sensors provide little or no additional value. In summary, the results suggest that topology, stiffness, and number of instrumented sensors should be co-designed for accurate PRC of soft robot states; stronger excitation alone cannot recover the diversity that poor design choices have already removed.

0.30

Tactile Reconstruction of Contact Task Frames and Forces for Hybrid Force/Motion Control

cs.RO ·2026-10-07 ·Antonio Rapuano, Simone Orelli, Barbara Bazzana, Antonio Franchi, Alessandro De Luca
similarity 0.59
Abstract · 14 pages, 9 figures, 7 tables. Video: https://youtube.com/playlist?list=PLejKMZmW8AvI. Dataset: https://doi.org/10.5281/zenodo.23209032

Hybrid force/motion control requires knowledge of the interaction force and of a task frame defining the force- and motion-controlled directions. These quantities are usually obtained from force/torque sensing or model-based residuals, often assuming also a nominal environment model. This work addresses the online estimation of the contact force and a possibly time-varying task frame using only soft optical tactile sensing, under the assumption of locally planar contact with a negligible contact moment. The proposed method maps a single image of the deformed elastomer of a soft optical tactile sensor to observable contact variables: indentation depth, two surface-to-sensor tilt angles, and 3D contact force, each with a per-sample uncertainty estimate. The mapping is learned through a self-labeling acquisition procedure, in which a manipulator imposes controlled contacts while an auxiliary Force/Torque sensor is used offline to provide ground-truth labels. The tactile measurement is then fused with robot proprioceptive data in an Extended Kalman Filter, producing a continuously updated estimate of the contact task frame and of the interaction force. Control experiments with a DigiTac sensor mounted on a UR10 manipulator demonstrate closed-loop contact force regulation against a flat rigid board in linear and angular motion by a human operator, with touch as the only exteroceptive feedback.

0.23

Single-View RGB-D Force--Deformation Estimation for Robotic Manipulation of Elasto-Plastic Materials

cs.RO ·2026-11-11 ·Dezhi Sun, Marijn van Hilten, Kenan Niu
published similarity 0.59
Abstract · 7 pages. Accepted at IEEE ROBIO 2026

Persistent deformation complicates elasto-plastic manipulation by coupling physical interaction with spatially distributed shape changes. We investigate the force--deformation relationship using a standard robot, a single eye-in-hand RGB-D camera, and intrinsic force estimates. A 7-DoF Franka Emika FR3 performs normal indentations while an Intel RealSense L515 captures pre- and post-contact surfaces. Point-cloud processing localizes deformation and estimates displaced volume. Force--volume characterization includes 27 measurements over nine force levels. A compact multilayer perceptron (MLP), trained on 52 force--volume pairs at four levels, achieves a held-out RMSE of 1.857 N and $R^2=0.440$. A separate comparison shows lower error for a quadratic model at 16 N and for the MLP at 19 and 23.5 N. An eight-step experiment at 4 N per interaction demonstrates cumulative deformation localization from the second indentation onward. These results establish a practical measurement basis for deformation-aware manipulation using intrinsic force estimates and single-view geometry.

0.28

3D-Force Estimation for Dual-arm Manipulation of Deformable Linear Objects via Factor Graphs

cs.RO ·2026-10-26 ·Annika Delucchi, Vincenzo Di Paola, Bruno Marco Quadrelli, Matteo Zoppi
similarity 0.58
Abstract

Estimating forces acting on Deformable Linear Objects (DLOs) is challenging due to their underactuated nature. However, reliable contact estimation is crucial to precisely control them and enable safe manipulation tasks. Differently from the various approaches presented in the literature, this work adopts a probabilistic formulation where the DLO state and sensor data are related through conditional distributions. In particular, factor graphs are used to determine the magnitude, direction, and location of a 3D force acting on a DLO, while simultaneously reconstructing its shape. Since DLOs are not actuated and are typically thin, like cables and wires, strain gauges and actuation readings are usually impractical. Therefore, to overcome this issue, this work is tested using one type of sensing information only, thus developing a generic technique suited for a wider variety of tasks. Realistic tests are performed by introducing noise into the measurements while the DLO follows a prescribed path in the presence of external forces that are accurately estimated.

0.33

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.58
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

Task-space model-based control of pneumatic soft actuators

cs.RO ·2026-08-27 ·Nithin S. Kumar, Joshua Gaston, D. Caleb Rucker, Eric J. Barth
top venue similarity 0.58
Abstract · 11 pages, 14 figures

Soft actuators enable dexterous and compliant interaction, but closed-loop task-space control remains challenging due to strong nonlinearities, distributed deformation, and uncertainty in their dynamics. This paper presents a real-time dynamic-model-based task-space feedback and estimation framework based on a non-minimal coordinate discrete elastic rod model formulated in absolute coordinates with holonomic constraints. The resulting structure preserves distributed mechanics while maintaining computational efficiency through sparse system matrices, enabling real-time control with up to 10 discretized rods. A quasi-static feedforward inverse model is combined with a task-space PI controller and a dynamic observer that fuses measurement residuals as virtual forces, enabling full-state estimation from sparse sensing. The approach is experimentally validated on three planar pneumatic soft actuators with varying geometries. Across five tasks, including drawing the digits 0-9 across the workspace (3-18 mm/s tip speed), tracking periodic motion (up to 37 cm/s), cross-platform generalization, reduced sensing conditions, and real-time user-defined references, our method achieves 1.5-2.3 mm root mean square error (RMSE) for precision motions and 5.5-12.4 mm RMSE at 1-2 Hz. Results demonstrate that structured, non-minimal dynamic models can enable real-time, high-precision, moderate-bandwidth task-space control of planar soft pneumatic actuators in free space.

0.27