CS Paper Radar

A Monolithic Force-Proprioception Soft Acutuator Enabled by Single-Material 3D printing

Nan Huang, Lele Liu, Junfeng Lu, Yipan Zhu, Jiansheng Dai, Sicong Liu

cs.RO ·submitted 2026-09-21 12:40 UTC · v1

Abstract

Pneumatic proprioceptive actuators integrate actuation and sensing for soft robots that attract interest due to functional potential. Existing approaches often suffer from assembly errors or stress concentrations caused by heterogeneous materials. In this work, we propose the Monolithic Force-Proprioception Soft (MFPS) design and fabrication method that integrates an Asymmetric Origami Bending (AOB) chamber and a Force-Proprioception Soft (FPS) sensor with single material through one-step Fused Deposition Modeling (FDM) fabrication. Based on the resistance response to strain of conductive thermoplastic polyurethane (TPU), we design and analyze the structure of the FPS sensor, and conduct parametric analysis on the sensing characteristics. The FDM fabrication parameters of the MFPS actuator are analyzed, followed by actuator fabrication and characterization of the actuation and proprioception performance. Experimental results show that the MFPS actuator achieves a bending angle of 40°, an output force of 12.5 N, and a resistance change of 26.9% as the applied external force increased from 0 to 45 N. A two-finger force-proprioception gripper is developed based on the MFPS actuator. The grasping and force-proprioception capabilities are experimentally validated, proving that the MFPS design method provides a new approach for the development of self-sensing actuators.

Closest papers

Nearest neighbours by meaning across the whole index.

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.65
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.62
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14

Task-space model-based control of pneumatic soft actuators

cs.RO ·2026-08-27 ·Nithin S. Kumar, Joshua Gaston, D. Caleb Rucker, Eric J. Barth
top venue similarity 0.61
Abstract · 11 pages, 14 figures

Soft actuators enable dexterous and compliant interaction, but closed-loop task-space control remains challenging due to strong nonlinearities, distributed deformation, and uncertainty in their dynamics. This paper presents a real-time dynamic-model-based task-space feedback and estimation framework based on a non-minimal coordinate discrete elastic rod model formulated in absolute coordinates with holonomic constraints. The resulting structure preserves distributed mechanics while maintaining computational efficiency through sparse system matrices, enabling real-time control with up to 10 discretized rods. A quasi-static feedforward inverse model is combined with a task-space PI controller and a dynamic observer that fuses measurement residuals as virtual forces, enabling full-state estimation from sparse sensing. The approach is experimentally validated on three planar pneumatic soft actuators with varying geometries. Across five tasks, including drawing the digits 0-9 across the workspace (3-18 mm/s tip speed), tracking periodic motion (up to 37 cm/s), cross-platform generalization, reduced sensing conditions, and real-time user-defined references, our method achieves 1.5-2.3 mm root mean square error (RMSE) for precision motions and 5.5-12.4 mm RMSE at 1-2 Hz. Results demonstrate that structured, non-minimal dynamic models can enable real-time, high-precision, moderate-bandwidth task-space control of planar soft pneumatic actuators in free space.

0.27

VecTile: A Low-Cost Flexible Tactile Array for 3-DoF Force Sensing

cs.RO ·2026-10-22 ·Jian Hou, Xin Zhou, Adam J. Spiers
similarity 0.60
Abstract · 8 pages, 8 figures. Submitted to IEEE International Conference on Robotics and Automation (ICRA) 2027

Tactile sensing provides robots with contact information difficult to obtain from vision alone. Shear force is particularly important for understanding tangential contact, guiding corrective motions, and maintaining grasp stability, yet flexible and low-cost tactile arrays often measure only normal force. We introduce VecTile, a low-cost, 6 mm thin, flexible tactile array capable of three-axis force sensing. VecTile combines a piezoresistive layer with passive silicone nubs that convert normal and shear forces into distinguishable pressure patterns. The sensor can be fabricated in-house without specialized equipment. The complete system costs less than 35 USD for a 4x4 array. We validate the sensing mechanism through finite element analysis and hardware experiments. In controlled single-taxel tests over 1-5 N normal force and up to 1.5 N shear force, VecTile achieves root-mean-square errors of 0.39 N and 0.16 N for normal and shear forces. A VecTile calibrated while flat retains accuracy when curved, while a five-minute manual calibration is sufficient for practical use. Two applications demonstrate its utility. First, shear readings are sensitive enough to stop a sharp scalpel from puncturing a balloon after contact. Second, the sensor substantially improves Diffusion Policy-guided power-plug insertion. All designs and code will be released upon paper acceptance. Project website: https://jiannnh.github.io/VecTile/.

0.20

History-Aware Force Sensing and Tunable Stiffness in a Pneumatic Kresling Origami Cell

cs.RO ·2026-11-01 ·Hengyi Zhou, Jiaqi Wang, Yilin Ma, Dezhong Tong, Xiaonan Huang
similarity 0.60
Abstract

Mechanical hysteresis and pneumatic loading complicate contact force estimation from deformation measurements in soft robots. This work presents a 3D-printed polyether block amide (PEBA) Kresling cell with magnetic angular sensing that supports three operating modes: force sensing at zero gauge pressure, force sensing with tunable stiffness under gauge positive pressure, and self-sensing actuation under negative gauge pressure. A multiscale gated recurrent unit (GRU) network estimates contact force from angular histories to account for the the combined effects of geometric deformation and material response. At zero gauge pressure, the model achieves a test RMSE of 0.76~N. Positive gauge pressure approximately doubles the average axial loading stiffness at +20~kPa over the first 3~mm of compression, while pressure-specific models maintain RMSEs below 0.93~N. Under negative gauge pressure, an energy-based compensation model enables contact force estimation using the the model trained at zero gauge pressure, achieving RMSEs of 1.66--2.10~N under quasi-static conditions. These results demonstrate a compact approach to combining force feedback, tunable axial stiffness, and self-sensing actuation in soft origami systems.

0.36

Design and Experimental Validation of a 3D Printed Torsional Series Elastic Actuator for Safe Human Robot Interaction

cs.RO ·2026-09-16 ·Joel Hidalgo Pisco, Melissa Cobos Condo, Luigi Miranda, Dennys Paillacho
published similarity 0.60
Abstract

Ensuring intrinsic safety in physical human robot interaction (pHRI) is a critical requirement for social and service robots. While Series Elastic Actuators (SEAs) offer hardware based compliance, traditional metallic designs often require complex, multi part assemblies. This paper presents the design, finite element analysis (FEA), and experimental validation of a low stiffness, torsional spring for SEAs, manufactured via 3D printed thermoplastic polyurethane (TPU). The compliant element exhibits a highly linear torque deformation response (Ks = 0.066 Nm/degree), matching numerical predictions with under 3% deviation, a variance attributed to FDM structural anisotropy. To accommodate external interactions using standard position limited servomotors, a hybrid position controller with torque threshold switching was implemented. Experimental evaluations demonstrate the system ability to accurately track non stationary trajectories and safely yield to external disturbances. Furthermore, the inherent material damping of the TPU acts as a passive low pass filter, preventing high frequency oscillations during control mode transitions. The proposed architecture offers a cost effective, reliable, and easily manufacturable solution for safe pHRI.

0.32

Manufacturing Complex Airtight Soft Pneumatic Actuators for Soft Robotics: Process Evaluation and Optimization

cs.RO ·2026-08-13 ·Mohammed Abboodi
published similarity 0.60
Abstract

Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications

0.20

SaddleSense: Saddle-Shaped Modules for 3D Shape Sensing with Single-Axis Off-the-Shelf Bend Sensors

cs.RO ·2026-10-31 ·Dong Heon Han, Runze Zuo, Chankyo Kim, Saima Jamal, Daniel Bruder
similarity 0.58
Abstract

Accurate posture feedback is essential for precise control of continuum robots. Off-the-shelf bend sensors measure curvature about only one axis; without a suitable mounting arrangement, they can restrict robot motion and provide incomplete posture information. SaddleSense introduces a 3D-printed thermoplastic polyurethane (TPU) saddle-shaped lattice that holds one commercial bend sensor along each curved edge. Because each sensor flexes within its own channel rather than spanning the segment axially, the lattice converts multi-axis body deformation into sensor curvature without tying segment length to sensor length. Each four-sensor module accommodates two-axis bending, contraction, and extension while quantifying all three deformation modes across its four readings. A hybrid calibration maps the sensor readings to piecewise constant curvature (PCC) parameters using a learned model paired with a physics-based fallback for out-of-distribution inputs. We demonstrate a six-module prototype with 24 off-the-shelf bend sensors on a 430~mm continuum body. Using only each module's four local readings, the physics-based model alone achieves a tip position root mean square error (RMSE) of 29.9~mm (7.0\% of body length). The data-driven model reduces the tip RMSE to 13.2~mm (3.1\%) on held-out samples of motions similar to the training set and 15.8~mm (3.7\%) on separately recorded trials. Reducing each module from four sensors to one nearly triples the tip error.

0.32