CS Paper Radar

Towards end-to-end co-design for one-shot printable task-specific soft robots

James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti

cs.RO ·submitted 2026-11-02 14:39 UTC · v1

Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

Closest papers

Nearest neighbours by meaning across the whole index.

PneuGen: Task-Driven Agentic Co-Design of Soft Pneumatic Robots

cs.RO ·2026-11-09 ·Shaohong Zhong, Marco Pontin, Perla Maiolino
similarity 0.72
Abstract

Task-driven design of soft robots requires the consideration of factors such as geometry, morphology, material properties, and actuation, resulting in a large and complex design space that is challenging to explore. Computational optimisation methods leverage signals from simulation to iteratively improve designs to achieve task objectives. However, these methods typically demand high computational load for both optimisation and simulation. We present PneuGen, an agentic co-design framework for soft robots that leverages Large Language Model (LLM) agents to search over the soft robot design space efficiently. A designer agent proposes design programs from a parametric component library, and a separate critic agent analyses simulation diagnostics and recommends targeted revisions. Fitted module response models provide reusable physical priors relating geometry and pressure to deformation. Design programs are automatically validated and converted into finite-element simulations, enabling iterative evaluation. Across grasping tasks on primitive shapes and challenging objects, as well as shape-matching tasks that require multi-directional planar and 3D deformation, the proposed framework significantly outperforms prior computational optimisation baselines. Ablation experiments also highlight the utility of the critic agent and the module response model in facilitating efficient design. We additionally demonstrate the agent-generated soft robot designs in real-world shape-matching and grasping tasks.

0.11

One Print, Many Moves: Monolithic Origami-inspired Folding Actuator for Composable Soft Multi-DoF Systems

cs.RO ·2026-09-01 ·Jaehyung Jang, Zhenish Zhakypov, Jasmin Elena Palmer, Melissa Klein, Jee-Hwan Ryu +1 more
similarity 0.71
Abstract · 26 pages, 7 figures

Conventional soft robot actuators excel in compliance, but their uncontrolled deformations compromise accuracy and hinder scaling to multi-degree-of-freedom (DoF) systems. We introduce a MONOlithic ORIGAMI-inspired soft folding actuator design (MONORIGAMI) that establishes a design strategy based on spatially programmed stiffness anisotropy to preserve material compliance along desired folding directions while selectively restricting deformation in unwanted directions. The actuator leverages stiffness tiers based on material thickness, patterned in an origami-inspired geometry with facets and creases, converting unconstrained soft deformation into accurate, repeatable, and composable folding motions without additional reinforcements. The design is fully 3D-printable through a single-material, single-print process that requires no assembly. Each actuator serves as a scalable motion primitive, and linking and orienting multiple actuators mechanically programs multi-DoF trajectories. Using the same fundamental module, we demonstrate three 3D-printed soft multi-DoF robotic systems spanning distinct application domains: (1) a compact 4-DoF wearable haptic device for high-fidelity cutaneous feedback in virtual reality (VR), (2) a 3-DoF joystick for kinesthetic feedback in teleoperation, and (3) a modular robotic gripper capable of underwater operation with geometry-encoded grasp trajectories. These systems demonstrate the module's capabilities for compact multi-axis integration, controlled physical interaction, and geometry-programmed operation across different environments. Together, these results show that MONORIGAMI provides a general, composable, accessible, reliable, and scalable platform for high-precision soft multi-DoF robotics, addressing long-standing limitations in both soft actuator design and fabrication.

0.14

TO-mdiSPAs: Topology Optimization of multi-directional Soft Pneumatic Actuators

cs.RO ·2026-09-30 ·Swagatam Islam Sarkar, Prabhat Kumar
similarity 0.70
Abstract · 6 pages

Soft pneumatic actuators (SPAs) are highly promising and have been extensively explored within the field of soft robotics. Under pneumatic pressure loads, an SPA undergoes bending deformation to perform specific tasks. A multi- or omni-directional SPA can bend and move in any direction within a 3D space, leveraging its multiple degrees of freedom to realize various mechanical functions. This work presents a systematic methodology using topology optimization (TO) to achieve an optimized design for a multi-directional SPAs. To ensure manufacturing robustness, a three-field TO formulation considering blueprint, dilated, and eroded designs is implemented. Additionally, Darcy's law, incorporating a drainage term, is used to model the design-dependent nature of the pneumatic loading. A min-max optimization problem is formulated based on the target output deformations of the SPA unit and solved using the Method of Moving Asymptotes. The optimization yields a high-performing, unconventional geometric design. Finally, numerical simulations demonstrate that the optimized SPA successfully achieves versatile multi-directional movements.

0.35

Manufacturing Complex Airtight Soft Pneumatic Actuators for Soft Robotics: Process Evaluation and Optimization

cs.RO ·2026-08-13 ·Mohammed Abboodi
published similarity 0.69
Abstract

Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications

0.20

PneuTac: Tactile Manipulation with Soft Pneumatic Robots via Unified MPM-Gaussian Splatting Simulation

cs.RO ·2026-09-29 ·Shaohong Zhong, Marco Pontin, Joe Watson, Perla Maiolino, Ingmar Posner
similarity 0.68
Abstract

Soft robots and tactile sensors have demonstrated great potential in delicate manipulation tasks. Soft pneumatic robots enable safe contact through compliance, and vision-based tactile sensors offer high-resolution touch perception. However, learning tactile manipulation with compliant robots has been challenging, bottlenecked by the lack of efficient simulation. Existing simulators typically model them in isolation, and exhibit large calibration gaps that are difficult to overcome efficiently. We present PneuTac, a unified framework for tactile-feedback manipulation with soft pneumatic robots. We leverage the material point method (MPM) for modelling the dynamics of the soft robot and the deformable tactile membrane, and 3D Gaussian splatting (3DGS) for rendering. Real-to-sim modelling is done with a simple vision-based method, to then train action and perception networks for efficient simulation with surrogate models. We use the framework to drive a tactile-guided pipeline to collect demonstrations in simulation. Through experiments on a custom-designed pneumatic soft finger with a tactile sensing tip, together with additional cross-device evaluations, we show that PneuTac is capable of accurately modelling soft robots with tactile sensors, and that policies trained with simulation-augmented demonstrations outperform baselines trained on the same real data on three real-world contact-rich compliant manipulation tasks, making it a practical framework for tactile manipulation on compliant hardware.

0.15

Design Optimization for Large High-Force Soft Robot Manipulators Under Gravitational Loads

cs.RO ·2026-08-17 ·Isara Cholaseuk, Penelope Llibre, Alexa Kyriacou, Audrey Wang, Akua K. Dickson +3 more
top venue similarity 0.67
Abstract · 8 pages, 8 figures

Designing large soft robots capable of generating high forces for physical human-robot interaction remains a significant challenge in soft robotics. Prior work in large soft robots has focused on proof-of-concept prototypes, and no systematic framework exists for determining the suitability of a design paradigm for a desired task. This manuscript introduces a method for optimizing the geometry of a soft robot limb, maximizing its blocking force subject to an anti-bucking constraint under its own gravitational loading. We demonstrate that an explicit solution exists to the proposed optimization problem under certain assumptions. Experiments with three geometries of a large, soft, pneumatically-actuated manipulator demonstrate that the method correctly predicts which designs meet constraints and which produces the largest end-effector forces. This method, with its closed-form solution, can allow designers to determine a-priori if an intended class of soft manipulators is an appropriate choice for physical interaction at large size scales.

0.54

Task-space model-based control of pneumatic soft actuators

cs.RO ·2026-08-27 ·Nithin S. Kumar, Joshua Gaston, D. Caleb Rucker, Eric J. Barth
top venue similarity 0.67
Abstract · 11 pages, 14 figures

Soft actuators enable dexterous and compliant interaction, but closed-loop task-space control remains challenging due to strong nonlinearities, distributed deformation, and uncertainty in their dynamics. This paper presents a real-time dynamic-model-based task-space feedback and estimation framework based on a non-minimal coordinate discrete elastic rod model formulated in absolute coordinates with holonomic constraints. The resulting structure preserves distributed mechanics while maintaining computational efficiency through sparse system matrices, enabling real-time control with up to 10 discretized rods. A quasi-static feedforward inverse model is combined with a task-space PI controller and a dynamic observer that fuses measurement residuals as virtual forces, enabling full-state estimation from sparse sensing. The approach is experimentally validated on three planar pneumatic soft actuators with varying geometries. Across five tasks, including drawing the digits 0-9 across the workspace (3-18 mm/s tip speed), tracking periodic motion (up to 37 cm/s), cross-platform generalization, reduced sensing conditions, and real-time user-defined references, our method achieves 1.5-2.3 mm root mean square error (RMSE) for precision motions and 5.5-12.4 mm RMSE at 1-2 Hz. Results demonstrate that structured, non-minimal dynamic models can enable real-time, high-precision, moderate-bandwidth task-space control of planar soft pneumatic actuators in free space.

0.27

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.66
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23