CS Paper Radar

Manufacturing Complex Airtight Soft Pneumatic Actuators for Soft Robotics: Process Evaluation and Optimization

Mohammed Abboodi

cs.RO ·submitted 2026-08-13 13:38 UTC · v2
published

Abstract

Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications

DOI
10.12974/2311-8717.2026.14.09

Closest papers

Nearest neighbours by meaning across the whole index.

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.69
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14

TO-mdiSPAs: Topology Optimization of multi-directional Soft Pneumatic Actuators

cs.RO ·2026-09-30 ·Swagatam Islam Sarkar, Prabhat Kumar
similarity 0.64
Abstract · 6 pages

Soft pneumatic actuators (SPAs) are highly promising and have been extensively explored within the field of soft robotics. Under pneumatic pressure loads, an SPA undergoes bending deformation to perform specific tasks. A multi- or omni-directional SPA can bend and move in any direction within a 3D space, leveraging its multiple degrees of freedom to realize various mechanical functions. This work presents a systematic methodology using topology optimization (TO) to achieve an optimized design for a multi-directional SPAs. To ensure manufacturing robustness, a three-field TO formulation considering blueprint, dilated, and eroded designs is implemented. Additionally, Darcy's law, incorporating a drainage term, is used to model the design-dependent nature of the pneumatic loading. A min-max optimization problem is formulated based on the target output deformations of the SPA unit and solved using the Method of Moving Asymptotes. The optimization yields a high-performing, unconventional geometric design. Finally, numerical simulations demonstrate that the optimized SPA successfully achieves versatile multi-directional movements.

0.35

A Monolithic Force-Proprioception Soft Acutuator Enabled by Single-Material 3D printing

cs.RO ·2026-09-21 ·Nan Huang, Lele Liu, Junfeng Lu, Yipan Zhu, Jiansheng Dai +1 more
similarity 0.60
Abstract

Pneumatic proprioceptive actuators integrate actuation and sensing for soft robots that attract interest due to functional potential. Existing approaches often suffer from assembly errors or stress concentrations caused by heterogeneous materials. In this work, we propose the Monolithic Force-Proprioception Soft (MFPS) design and fabrication method that integrates an Asymmetric Origami Bending (AOB) chamber and a Force-Proprioception Soft (FPS) sensor with single material through one-step Fused Deposition Modeling (FDM) fabrication. Based on the resistance response to strain of conductive thermoplastic polyurethane (TPU), we design and analyze the structure of the FPS sensor, and conduct parametric analysis on the sensing characteristics. The FDM fabrication parameters of the MFPS actuator are analyzed, followed by actuator fabrication and characterization of the actuation and proprioception performance. Experimental results show that the MFPS actuator achieves a bending angle of 40°, an output force of 12.5 N, and a resistance change of 26.9% as the applied external force increased from 0 to 45 N. A two-finger force-proprioception gripper is developed based on the MFPS actuator. The grasping and force-proprioception capabilities are experimentally validated, proving that the MFPS design method provides a new approach for the development of self-sensing actuators.

0.20

Freeform Programmable Liquid Crystal Elastomers via Monolithic Integration of Co-Optimization and 4D-Printing

cs.CE math.OC ·2026-10-23 ·Yibo Wang, Asad Farooq Ahmed, Weichen Li, Weiyun Xu, Xiaojia Shelly Zhang
similarity 0.59
Abstract

Liquid crystal elastomers (LCEs) are active materials capable of large, reversible thermally induced actuation, offering significant potential for applications such as artificial muscles and soft robotics. However, their broader deployment is hindered by the lack of a unified design-to-fabrication framework, the strong coupling among geometry, director fields, and manufacturing constraints, and the difficulty of reliably translating complex designs into physically realizable architectures. Here, we present an autonomous and monolithic integration of co-optimization and 4D printing that enables the end-to-end design-to-realization of versatile programmable LCE architectures with superior precision, complexity, and versatility. The proposed framework establishes a unified design strategy that co-optimizes the freeform multilayer geometry and fully continuous layer-specific director distributions, and subsequently translates the optimized fields into fabrication-ready DIW toolpaths through an automated manufacturing-aware pipeline. To bridge computation and realization, we develop an optimization-centered 4D printing approach with automated, fabrication-aware toolpath generation tailored for direct ink writing of LCEs. With the proposed design-to-fabrication paradigm, we experimentally realize architectures that exhibit complex, non-intuitive thermo-mechanical behaviors. Experiments achieve highly challenging prescribed functionalities beyond the reach of intuition-based approaches and show excellent agreement with numerical simulations across all samples. This work establishes a generalizable inverse design and physical realization of freeform programmable LCE systems, enabling function-oriented and optimization-driven intelligent LCE applications for next-generation soft robotic and responsive material engineering.

0.23

Process-Aware Thickness Analysis in CAD Models using Hybrid Geometric Methods

cs.CE ·2026-09-14 ·Serafeim Baltadouros, Joost R. Duflou
similarity 0.55
Abstract

Thickness is a critical geometric attribute in Design for Manufacturability (DFM), yet its computational analysis in CAD environments remains largely process-agnostic. Existing approaches rely either on inscribed-sphere or ray-casting methods, each carrying limitations that make them poorly suited as universal solutions across manufacturing processes. This paper presents a process-aware thickness analysis system for parts intended for molding and milling, where the geometric method is selected and its outputs interpreted according to the DFM rules meaningful to each process. For molding, the sphere-based method detects maximum thickness violations and wall non-uniformity, and segments parts into distinct thickness zones. For milling, ray-casting identifies regions of insufficient thickness and detects thin features prone to deflection or failure. Validation on representative parts demonstrates that this hybrid approach surfaces process-specific manufacturability issues, offering designers actionable geometric feedback early in the design cycle.

0.09

PneuGen: Task-Driven Agentic Co-Design of Soft Pneumatic Robots

cs.RO ·2026-11-09 ·Shaohong Zhong, Marco Pontin, Perla Maiolino
similarity 0.53
Abstract

Task-driven design of soft robots requires the consideration of factors such as geometry, morphology, material properties, and actuation, resulting in a large and complex design space that is challenging to explore. Computational optimisation methods leverage signals from simulation to iteratively improve designs to achieve task objectives. However, these methods typically demand high computational load for both optimisation and simulation. We present PneuGen, an agentic co-design framework for soft robots that leverages Large Language Model (LLM) agents to search over the soft robot design space efficiently. A designer agent proposes design programs from a parametric component library, and a separate critic agent analyses simulation diagnostics and recommends targeted revisions. Fitted module response models provide reusable physical priors relating geometry and pressure to deformation. Design programs are automatically validated and converted into finite-element simulations, enabling iterative evaluation. Across grasping tasks on primitive shapes and challenging objects, as well as shape-matching tasks that require multi-directional planar and 3D deformation, the proposed framework significantly outperforms prior computational optimisation baselines. Ablation experiments also highlight the utility of the critic agent and the module response model in facilitating efficient design. We additionally demonstrate the agent-generated soft robot designs in real-world shape-matching and grasping tasks.

0.12

Real-time Puncture Detection and Recovery for Pneumatic Soft Actuators

cs.RO ·2026-09-08 ·Tejonidhi R. Deshpande, Tingyu Cheng, Josiah Hester
top venue similarity 0.52
Abstract · Accepted at IEEE ICRA 2026

Soft robots offer safe and adaptive interaction with humans and unstructured environments through their inherent ability to deform and comply. Pneumatic actuators are one way to build soft robots. They are typically made from soft silicone materials and are especially effective for driving such systems, enabling smooth and adaptable motion. However, their compliant nature also makes them vulnerable to mechanical failures like punctures and tears, limiting practical deployment. To address this, we propose a puncture detection system for soft actuators using motion data from a single inertial measurement unit. Extracted features are used to train anomaly detectors for puncture detection and non-linear models to estimate severity. We also introduce a multi-chamber pneumatic soft bending actuator capable of diverse configurations via selective chamber inflation. Our algorithm identifies the punctured chamber and provides a severity score using a chamber perturbation scheme. Anomaly detectors are trained on normal operation data and detect damage through reconstruction errors, while severity is estimated by a separate model trained under slightly modified conditions. Finally, we demonstrate a failure recovery strategy to maintain actuation force post-failure. This approach enhances the reliability and safety of soft robotic systems through real-time, data-driven damage detection.

0.41

Robot Aware Computational Design of Object Specific Passive Grippers for Additive Manufacturing

cs.RO ·2026-09-03 ·Abdullah Yahya Abdullah Omaisan, Ibrahim Sheikh Mohamed
similarity 0.52
Abstract

This paper presents an end-to-end computational pipeline that converts a selected object mesh, a measured object state, and a selected six-axis robot into an object-specific, unactuated, additively manufacturable gripper. The method couples exact-mesh RGB-D/ICP pose registration, deterministic surface-contact sampling, uncertainty-aware wrench screening, selection among six passive capture mechanisms, object-conformal surface synthesis, full-orientation robot inverse kinematics, a swept-volume-aware manufacturing domain, directional fused-deposition finite-element screening, and constrained three-dimensional SIMP topology optimization. Unlike workflows that treat grasp selection, tool geometry, motion, and structural design as separate problems, every exported design is bound to the source mesh, object pose, robot flange, contact set, and insertion hypothesis by a traceable design identifier. We derive the implemented registration, contact, fit-tolerance, finite-element, and density-optimization equations and prove three properties of the numerical construction: nodal load preservation, monotonic compliance sensitivity under SIMP interpolation, and voxel-domain containment after topology post-processing. Four archived object-specific attempts - a rabbit, camera flange, 3DBenchy, and faceted bust - meet the nominal fit, uncertain-wrench, runtime-sweep, and baseline/post-topology FEA gates. A deliberately enlarged +/-3 mm, +/-5 degree pose stress check differentiates the designs, retaining 29-134 of 160 simulated trials. Their reconstructed topologies retain 92.0-97.6% of the FE domain because functional regions are protected. Archived robot photographs show the corresponding printed assemblies qualitatively, while nominal material properties and absent coupon-calibrated, instrumented tests keep all four at digital-screening status rather than operational release.

0.25