CS Paper Radar

Robot Aware Computational Design of Object Specific Passive Grippers for Additive Manufacturing

Abdullah Yahya Abdullah Omaisan, Ibrahim Sheikh Mohamed

cs.RO ·submitted 2026-09-03 12:29 UTC · v1

Abstract

This paper presents an end-to-end computational pipeline that converts a selected object mesh, a measured object state, and a selected six-axis robot into an object-specific, unactuated, additively manufacturable gripper. The method couples exact-mesh RGB-D/ICP pose registration, deterministic surface-contact sampling, uncertainty-aware wrench screening, selection among six passive capture mechanisms, object-conformal surface synthesis, full-orientation robot inverse kinematics, a swept-volume-aware manufacturing domain, directional fused-deposition finite-element screening, and constrained three-dimensional SIMP topology optimization. Unlike workflows that treat grasp selection, tool geometry, motion, and structural design as separate problems, every exported design is bound to the source mesh, object pose, robot flange, contact set, and insertion hypothesis by a traceable design identifier. We derive the implemented registration, contact, fit-tolerance, finite-element, and density-optimization equations and prove three properties of the numerical construction: nodal load preservation, monotonic compliance sensitivity under SIMP interpolation, and voxel-domain containment after topology post-processing. Four archived object-specific attempts - a rabbit, camera flange, 3DBenchy, and faceted bust - meet the nominal fit, uncertain-wrench, runtime-sweep, and baseline/post-topology FEA gates. A deliberately enlarged +/-3 mm, +/-5 degree pose stress check differentiates the designs, retaining 29-134 of 160 simulated trials. Their reconstructed topologies retain 92.0-97.6% of the FE domain because functional regions are protected. Archived robot photographs show the corresponding printed assemblies qualitatively, while nominal material properties and absent coupon-calibrated, instrumented tests keep all four at digital-screening status rather than operational release.

Closest papers

Nearest neighbours by meaning across the whole index.

SimTO-Robust: Automated Design of Soft Grippers Robust to Grasp Pose and Object Geometry

cs.RO ·2026-10-29 ·Kurt Enkera, Joshua Pinskier, Marcus Gallagher, David Howard
similarity 0.65
Abstract

Robotic grippers operating in unstructured environments must robustly grasp objects of different shapes and sizes despite perception and positioning errors. Soft grippers that can achieve this robustness through intelligent mechanical design rather than sophisticated control software offer a promising solution. However, no existing computational design framework explicitly optimises soft gripper morphology for robustness across object geometries and grasp poses. We introduce SimTO-Robust, a generalisation of simulation-driven topology optimisation (SimTO) that simulates grasps across multiple objects and poses and aggregates their contact forces to guide gripper morphology optimisation. We generate 6,646 designs and physically evaluate 24 of them alongside 10 specialised SimTO designs, two rigid baseline grippers, and a baseline generalist soft gripper produced using conventional topology optimisation. All 37 grippers are tested in a pick-and-place task involving five feature-rich objects and six grasp poses, with external disturbances of increasing magnitude applied during the task. On average, SimTO-Robust designs complete pick-and-place more reliably than specialised SimTO designs and the rigid baselines. The best SimTO-Robust designs also withstood more of the applied disturbances than any other tested gripper. These results show that incorporating diverse grasp conditions into simulation-driven topology optimisation is a simple and effective approach to improving real-world soft gripper robustness. More broadly, they show that robust robotic grasping can be achieved through intelligent mechanical design rather than sophisticated sensing and control.

0.24

Gripper-Aware Automatic Dense Packing of Irregular Objects

cs.RO ·2026-09-18 ·Tianhao Qin, Connor McCann, Berk Calli, Jing Xiao
publishedbenchmark similarity 0.65
Abstract · Accepted at ISRR 2026

Automatic dense packing is widely desired in warehouse operations but remains a fundamental challenge in robotic manipulation. Existing work on irregular-object packing largely targets simulation with idealized contact, treating the object as an isolated rigid body. The gripper often enters as a discrete, post-hoc feasibility check, if considered at all, and the perception and contact drift accumulated during execution are not addressed. We present a closed-loop pipeline that integrates perception, gripper-aware placement optimization, and force-guided execution on a real manipulator. The optimizer represents the object together with the gripper as a single composite body of hierarchical sphere trees. It searches over five degrees of freedom on a GPU within a CMA-ES framework, with the vertical coordinate grounded analytically against the current heightmap. During execution, a force-monitored vertical descent stops on first contact. A post-release consolidation push then closes the residual lateral clearance that gripper-aware planning leaves behind. The container is re-perceived between placements so that drift does not accumulate. We validate the system on a Franka Emika Panda robot packing a 3D-printed set of flat, curved, and concave objects, and a YCB object subset. An ablation study isolates the contribution of gripper-aware optimization, the consolidation push, and mesh-derived geometry to end-to-end success, achieved density, and computational cost. We further benchmark against the heightmap-minimization method as a baseline representative of prior irregular-object packing work.

0.31

LABIT: Long-Horizon Robotic Assembly Benchmark for Industrial Tasks

cs.RO ·2026-10-12 ·Constantin Schempp, Christian Friedrich, Luca Kofler, Laura Suhm
benchmarkcode/data similarity 0.65
Abstract · This work has been submitted to an Elsevier journal for possible publication. Copyright may be transferred without notice, after which this …

Robot learning has undergone significant advancements in the domain of compliant control and robotic assembly. The development of novel methodologies has transcended the capacity to address discrete tasks, such as grasping or inserting, and has evolved to encompass the comprehensive construction of entire assemblies. Conventional benchmarks, which are predominantly focused on single tasks, are no longer adequate to address the complexity and interconnected nature of modern manufacturing processes. Consequently, the necessity for benchmarks to encompass a broader spectrum of assembly and subassembly steps is becoming apparent. In light of these developments, we propose LABIT, an industrial robotic assembly benchmark for long-horizon manipulation. This benchmark encompasses DIN-norm assembly tasks, including screwing, placing, inserting, and snapping, under both high and low tolerance conditions. The successive nature of these assembly steps implies that prior errors can influence subsequent manipulation. Consequently, this benchmark is particularly relevant for assessing the robustness of intelligent robotic systems. The proposed benchmarking protocols and novel performance metric, based on a taxonomy of assembly complexity in conjunction with the comprehensive list of parts and their corresponding CAD models, serve as essential tools for research and development in the field. To provide a baseline, we evaluate the benchmark using traditional force-position control and report reliability and score metrics per primitive, subtask, assembly category, and subassembly. Accompanying data is available at https://irp-hka.github.io/robotic-assembly-benchmark/.

0.48

Kinematics-Grounded Agentic AI for Robotic Additive Manufacturing Process Planning

cs.RO cs.AIeess.SY ·2026-09-16 ·Jingzhan Ge, Ruimin Chen, Azadeh Haghighi, Jiong Tang, Farhad Imani
similarity 0.63
Abstract · 25 pages, 17 figures

Robotic additive manufacturing (AM) extends material-extrusion printing beyond gantry kinematics but makes process planning robot-dependent. A slicer-generated plan that appears favorable in part coordinates can become infeasible or robotically unfavorable on a manipulator because slicer-process decisions and part orientation determine the generated path, while part orientation and workspace placement affect its kinematic realization. Existing AM tools, large language model (LLM)-based decision-support methods, and digital-shadow systems do not provide integrated pre-execution evaluation of these coupled decisions. This paper presents agentic robotic additive manufacturing (A-RAM), an agent-specialist-tool framework that converts user intent and a part file into traceable, execution-ready plans. The LLM interprets manufacturing objectives and constraints, identifies prescribed and searchable planning variables, and encodes this reasoning in a schema-constrained request; a deterministic Planning Agent instantiates the corresponding search workflow, while domain tools compute quantitative evidence for slicing, placement, inverse kinematics, trajectory timing, Joint-6 jerk, and extrusion. The framework is evaluated on a six-axis robotic-arm AM cell through three case studies covering expert-specified planning, goal-only planning, objective-dependent infill screening, and geometry-dependent orientation-placement selection. Across the evaluated candidate sets, selected plans achieve up to 53.5% lower maximum Joint-6 jerk and 48.3% lower mean absolute Joint-6 jerk than the least favorable valid candidates, while objective-specific infill screening yields motion-plan completion times up to 40.1% shorter and extrusion paths up to 12.7% shorter than the corresponding least favorable screened patterns.

0.15

Tool-Policy Co-Design for Powder Weighing in Laboratory Automation

cs.RO ·2026-09-30 ·Nikola Radulov, Xin Yang, Kevin S. Luck, Gabriella Pizzuto
similarity 0.62
Abstract · Paper video can be found at https://youtu.be/BEUT70hX9LM

Autonomous powder weighing is one of many bottlenecks in laboratory automation due to the complex, non-linear dynamics of heterogeneous materials. Robot chemists performing this task utilise standard tools shaped for the dexterity of human hands, whose fixed geometry sets the dynamics that the control policy needs to regulate. This work introduces a tool-policy co-design framework that concurrently optimises the morphology of a dispensing tool and its control policy for use by robots in chemistry laboratories, formulated as a bi-level optimisation that minimises dispensing error over a target distribution of powder flowabilities. The outer loop varies tool-design parameters such as tool depth, width and rim spike topology using Bayesian optimisation and hyperband, while an inner loop optimises a control policy for each candidate morphology. We also introduce a geometric similarity metric that warm-starts policy training from cached policies of structurally similar designs, exploring 28% more configurations under the same compute budget. The proposed framework is evaluated on a robotic powder weighing task across seven materials with distinct physical dynamics in a flowability-informed robot-material simulation framework. Experimental results demonstrate that our co-designed tool morphology reduces real-world weighing errors by 45% relative to a standard tool, including on previously unseen materials. These results demonstrate our method can adapt both the control policy and the physical tool to the dynamics of the target material, bringing a new paradigm for material manipulation to the field of laboratory automation.

0.35

Optimization-Based Path Planning for Industrial Manipulators: Experimental Validation in Additive Manufacturing

cs.RO math.OC ·2026-11-10 ·Shiva Ganesh Murali, Valentin Bhend, Deepak Ingole, Gabriele Fadini, Alisa Rupenyan
similarity 0.62
Abstract · Submitted for the review in ECC 2027

Robotic additive manufacturing requires joint paths that reconcile robot feasibility with process-specific geometry. We develop an offline optimization-based path planner that combines joint-path regularity and self-collision penalties with process costs and constraints, so that a new process enters through its own reference, residuals, and tolerances. Full-path and boundary-coupled chunked optimization handle references of different lengths. Iterative Weight Tuning (IWT) determines the cost weights from the gaps between Key Performance Indicators (KPIs) and their targets. In carbon-fiber winding and robotic 3D printing, the planned paths meet the geometric tolerances and all KPI targets, and both paths are executed on a UR10e, without extrusion for printing, with joint-level tracking recorded during execution.

0.22

Embodiment-Aware Planning for Heterogeneous Bimanual Manipulation

cs.RO ·2026-10-16 ·Sukhvansh Jain, Anurag Maurya, Shivam Vats, Narendra Kumar Dhar, Ravi Prakash
similarity 0.59
Abstract · Please find the project website here: https://sukhvansh2004.github.io/Bimanual-Manipulation/

Many manipulation tasks that are effortless for dexterous human hands remain challenging for robotic systems equipped with simple, task-specialized grippers. Industrial platforms commonly rely on end-effectors such as suction cups or parallel-jaw grippers, yet no single mode can reliably satisfy the diverse constraints encountered across different phases of complex manipulation tasks, including pickup, reorientation, insertion, and constrained placement. In this work, we investigate whether complementary simple grippers within a heterogeneous bimanual setup can collectively realize tasks that exceed the capability of any individual gripper alone. Given a single human demonstration specifying the desired object motion, we formulate embodiment-aware execution as a finite-horizon optimization over arm-trajectory assignments. At each segment, the planner determines whether single-arm manipulation or a coordinated dual arm handover is required, jointly reasoning over heterogeneous grasp feasibility, motion constraints, manipulability, and cross-gripper compatibility. Exploiting this formulation, we compute globally consistent assignments with explicit switching regularization. Experiments on a dual Franka FR3 platform equipped with suction and parallel-jaw grippers demonstrate improved feasibility and reliability in tasks that are infeasible under single-gripper execution.

0.29

Contact-Stable Deformable Tissue Simulation Using Implicit Integration and Live-Pose Grasp Constraints for Laparoscopic Surgery Robot Policy Evaluation

cs.RO ·2026-09-22 ·Juahn Oh, Dongho Yee, Jinseok Lee, Jiyul Lee, Yechan Seo +7 more
hot direction similarity 0.59
Abstract · Submitted to IEEE ICRA 2027

Closed-loop evaluation of surgical robots requires tissue that deforms, can be grasped and lifted, and reproduces the anatomy in which the robot will operate. We present a simulator in which this tissue is reconstructed from a fixed-view RGB-D recording of the surgical field, composited to remove the instruments, closed into watertight volumes and tetrahedralised; the pipeline was applied unchanged to three specimens of two species (thirteen organs, 146,061 tetrahedra, no inverted elements). For one specimen, the organs are placed in a bimanual cell in which two Franka FR3 arms operate motorised instruments through 6 mm trocars. The core contribution is the numerical and contact design that keeps this cell stable: implicit integration, simulation meshes separate from collision meshes, numerical guards, and a grasp constraint captured at the live tissue pose. In 45 repeated grasp-lifts, a friction grasp held the tissue in 0 of 15 trials and each constraint grasp in 13 of 15; on displaced tissue, a rest-pose constraint produced one-step snaps of up to 17.8 mm, which live-pose capture eliminates. Against the recording, front-surface depth error is 1.33 to 1.41 mm, organ silhouette IoU is 0.80, and in five grasp-lifts reproduced from video the landmark displacement RMSE is 11.8 mm against 14.2 mm for a static prediction. Biofidelity is not claimed; the environment is intended for closed-loop feasibility, safety, contact and policy screening.

0.32