CS Paper Radar

Gripper-Aware Automatic Dense Packing of Irregular Objects

Tianhao Qin, Connor McCann, Berk Calli, Jing Xiao

cs.RO ·submitted 2026-09-18 17:53 UTC · v1
publishedbenchmark

Abstract

Automatic dense packing is widely desired in warehouse operations but remains a fundamental challenge in robotic manipulation. Existing work on irregular-object packing largely targets simulation with idealized contact, treating the object as an isolated rigid body. The gripper often enters as a discrete, post-hoc feasibility check, if considered at all, and the perception and contact drift accumulated during execution are not addressed. We present a closed-loop pipeline that integrates perception, gripper-aware placement optimization, and force-guided execution on a real manipulator. The optimizer represents the object together with the gripper as a single composite body of hierarchical sphere trees. It searches over five degrees of freedom on a GPU within a CMA-ES framework, with the vertical coordinate grounded analytically against the current heightmap. During execution, a force-monitored vertical descent stops on first contact. A post-release consolidation push then closes the residual lateral clearance that gripper-aware planning leaves behind. The container is re-perceived between placements so that drift does not accumulate. We validate the system on a Franka Emika Panda robot packing a 3D-printed set of flat, curved, and concave objects, and a YCB object subset. An ablation study isolates the contribution of gripper-aware optimization, the consolidation push, and mesh-derived geometry to end-to-end success, achieved density, and computational cost. We further benchmark against the heightmap-minimization method as a baseline representative of prior irregular-object packing work.

Comment
Accepted at ISRR 2026

Closest papers

Nearest neighbours by meaning across the whole index.

SimTO-Robust: Automated Design of Soft Grippers Robust to Grasp Pose and Object Geometry

cs.RO ·2026-10-29 ·Kurt Enkera, Joshua Pinskier, Marcus Gallagher, David Howard
similarity 0.71
Abstract

Robotic grippers operating in unstructured environments must robustly grasp objects of different shapes and sizes despite perception and positioning errors. Soft grippers that can achieve this robustness through intelligent mechanical design rather than sophisticated control software offer a promising solution. However, no existing computational design framework explicitly optimises soft gripper morphology for robustness across object geometries and grasp poses. We introduce SimTO-Robust, a generalisation of simulation-driven topology optimisation (SimTO) that simulates grasps across multiple objects and poses and aggregates their contact forces to guide gripper morphology optimisation. We generate 6,646 designs and physically evaluate 24 of them alongside 10 specialised SimTO designs, two rigid baseline grippers, and a baseline generalist soft gripper produced using conventional topology optimisation. All 37 grippers are tested in a pick-and-place task involving five feature-rich objects and six grasp poses, with external disturbances of increasing magnitude applied during the task. On average, SimTO-Robust designs complete pick-and-place more reliably than specialised SimTO designs and the rigid baselines. The best SimTO-Robust designs also withstood more of the applied disturbances than any other tested gripper. These results show that incorporating diverse grasp conditions into simulation-driven topology optimisation is a simple and effective approach to improving real-world soft gripper robustness. More broadly, they show that robust robotic grasping can be achieved through intelligent mechanical design rather than sophisticated sensing and control.

0.24

Hybrid Roller-Jamming Gripper for Object Acquisition and Retention Under Pose Uncertainty

cs.RO ·2026-08-21 ·Yijie Ren, Guillaume Gourmelen, Hiroyasu Iwata
published similarity 0.66
Abstract · 11 pages, 16 figures, under review

In household manipulation, pose uncertainty often results in off-centre or partial initial contact, making reliable object acquisition difficult. Roller-based grippers can actively draw objects inward but often provide limited post-capture stability, whereas granular-jamming grippers require sufficient contact before jamming to achieve strong retention. This paper presents a hybrid roller-jamming gripper that integrates active object intake and post-capture retention within a single gripper. The proposed gripper uses inward roller rotation to increase contact and draw the object toward the gripper centre, followed by vacuum-induced granular jamming to stiffen the rollers and stabilise the grasp. The paper also presents a simplified geometric analysis of the gripper and a bench-level characterisation of the prototype's force capability. The gripper prototype was mounted on a 7-DoF robotic arm and evaluated using eight test objects. Furthermore, controlled planar position and orientation offsets were applied, with each condition repeated three times. The main evaluation comprised 840 grasp trials, including 216 planar-offset trials and 624 orientation-offset trials. Overall, the gripper succeeded in 812/840 trials: 215/216 planar-offset trials and 597/624 orientation-offset trials. The ablation evaluation comprised 162 trials on three objects. The roller-only and jamming-only conditions achieved 54/81 and 24/81 successes, respectively, showing their different contributions. These results provide initial mechanism-level evidence that hybrid roller-jamming is a promising strategy for improving acquisition and retention after imperfect first contact.

0.41

GLoTouch: Global-to-Local Haptic Perception Using a Parallel Gripper for Object Search, Recognition, and Grasping Without External Vision

cs.RO ·2026-09-23 ·Zonglin Li, Wanruo Zhang, Yiming Wang, Kun Song, Xinyi Zhou +1 more
similarity 0.66
Abstract

Perceiving objects in the environment is a fundamental capability of autonomous robots. In dark or low-light environments, external cameras often fail to reliably perceive object positions and geometry; when visual sensing is unavailable, completing target search, recognition, and grasping through touch alone becomes a key robot manipulation capability. This task must simultaneously address container-scale spatial exploration and object-scale fine-grained geometric perception, which is particularly challenging for low-degree-of-freedom parallel grippers. However, a unified framework remains lacking for connecting container-scale spatial exploration with object-scale fine-grained geometric perception and grasping. To address this challenge, we present \textbf{GLoTouch}, a global-to-local haptic perception and manipulation framework built on a parallel gripper. In the global stage, the gripper holds a passive long-reach probe, combining force measurements with known tool geometry to localize contacts and actively estimate candidate-object positions, coarse contours, and heights. In the local stage, the robot sets down the probe and uses the bilateral visuotactile sensors on the same gripper to directly acquire local haptic observations, which are matched against a given target 3-D model without object-specific training. We evaluate the framework in both simulation and real-robot experiments. Source code will be open-sourced.

0.30

Robot Aware Computational Design of Object Specific Passive Grippers for Additive Manufacturing

cs.RO ·2026-09-03 ·Abdullah Yahya Abdullah Omaisan, Ibrahim Sheikh Mohamed
similarity 0.65
Abstract

This paper presents an end-to-end computational pipeline that converts a selected object mesh, a measured object state, and a selected six-axis robot into an object-specific, unactuated, additively manufacturable gripper. The method couples exact-mesh RGB-D/ICP pose registration, deterministic surface-contact sampling, uncertainty-aware wrench screening, selection among six passive capture mechanisms, object-conformal surface synthesis, full-orientation robot inverse kinematics, a swept-volume-aware manufacturing domain, directional fused-deposition finite-element screening, and constrained three-dimensional SIMP topology optimization. Unlike workflows that treat grasp selection, tool geometry, motion, and structural design as separate problems, every exported design is bound to the source mesh, object pose, robot flange, contact set, and insertion hypothesis by a traceable design identifier. We derive the implemented registration, contact, fit-tolerance, finite-element, and density-optimization equations and prove three properties of the numerical construction: nodal load preservation, monotonic compliance sensitivity under SIMP interpolation, and voxel-domain containment after topology post-processing. Four archived object-specific attempts - a rabbit, camera flange, 3DBenchy, and faceted bust - meet the nominal fit, uncertain-wrench, runtime-sweep, and baseline/post-topology FEA gates. A deliberately enlarged +/-3 mm, +/-5 degree pose stress check differentiates the designs, retaining 29-134 of 160 simulated trials. Their reconstructed topologies retain 92.0-97.6% of the FE domain because functional regions are protected. Archived robot photographs show the corresponding printed assemblies qualitatively, while nominal material properties and absent coupon-calibrated, instrumented tests keep all four at digital-screening status rather than operational release.

0.25

Receding-Horizon Pushing with Composable Object-Centric Policies

cs.RO ·2026-09-20 ·Zhiyi Yuan, Tianrun Hu, Anxing Xiao, Yuhong Deng, David Hsu +1 more
similarity 0.65
Abstract

Non-prehensile manipulation is practical for relocating large, heavy, or geometrically ungraspable objects. Yet, long-horizon pushing of arbitrarily-shaped 3D objects couples three problems: 1) where to push the object so as to approach the target pose, 2) whether each push is stable and reachable, 3) whether subsequent actions remain feasible. We present an object-centric pushing policy within a feedback-guided hierarchical framework. At the low level, a learning-based policy predicts contact actions from a pose- and scale-normalized point cloud, conditioned on a near single-step subgoal. A stability score is applied to evaluate the predicted contacts by a quasi-static sliding-versus-tipping analysis. At the high level, BIT$^*$ first searches for an object path, and the next several subgoals are checked by contact prediction and robot motion planning for future feasibility. Failed motion plans, as feedback, change the local path costs and trigger re-planning. During execution, only the first feasible action is executed. In simulation, we evaluate 22 objects in six different scenes, upon which we also conduct comprehensive ablation studies. Results demonstrate that our method outperforms baselines with a clear margin and can reliably achieve long-horizon object pushing tasks under different situations. We also report quantitative real-robot experiments with a Franka arm and qualitative demonstrations with a mobile manipulator for large and heavy objects, with directly zero-shot sim-to-real transfer.

0.26

Active Surface-Driven Reconfigurable Gripper: Robust Grasping and Sequential Manipulation of Thin Objects

cs.RO ·2026-08-27 ·Ziyi Zheng, Keqi Zhu, Hao Wu, Yanzhe Wang, Huixu Dong
published similarity 0.64
Abstract · Accepted by RSS2026

Robotic grippers face substantial challenges in grasping and manipulating thin objects. Most existing grippers rely on highly precise approach and grasp motions, which limits robustness and reduces applicability. This paper explores thin-object grasping using books as a representative example. Here, we propose a novel solution that integrates an active surface with underactuated compliance to achieve stable grasping of thin objects without complex control. First, an underactuated gripper with an active surface is designed. The active-surface thumb performs in-hand repositioning of the target book without requiring adjustments of the robot arm or the other fingers, while the underactuated fingers establish compliant contact conditions with the environment, and the reconfigurable structure enables reliable grasping of books under different configurations. Second, we establish a kinematic model of the gripper, and determine the initial grasp postures for two representative scenarios (books lying flat on a desktop and books vertically packed in a shelf). Third, by analyzing the physical model of a book lying on a table and its interaction with the gripper and the environment, we systematically optimize the structural parameters and grasping strategy. Finally, extensive experiments validate the effectiveness of the proposed gripper and strategy. The results demonstrate strong robustness and adaptability when grasping thin objects placed flat (including books, paper, fabric, plastic film, and mouse pad), as well as a high success rate when grasping vertically packed books. Moreover, the proposed gripper can reliably complete long sequential "grasp-place" tasks.

0.21

PackLab: A Comprehensive Framework for Developing, Training, and Evaluating MLLMs in Robotic Bin Packing

cs.RO ·2026-09-20 ·Donghao Zhou, Jia-Hui Pan, Fan Zhang, Xingyuan Bu, Shilong Li +4 more
benchmarkcode/data similarity 0.64
Abstract · The code, model, dataset, and benchmark are available at https://github.com/Correr-Zhou/PackLab

Robotic bin packing requires long-horizon sequential decision-making, as each object placement affects the available space for subsequent packing. Existing methods primarily rely on hand-crafted geometric heuristics that optimize predefined objectives or reinforcement learning policies learned through trial and error over predefined training configurations. Despite recent advances in multimodal large language models (MLLMs) for this task, their potential for closed-loop sequential decisions across heterogeneous packing configurations remains underexplored. To address this gap, we introduce PackLab, a comprehensive framework for developing, training, and evaluating MLLMs for closed-loop robotic bin packing. PackLab-Suite provides a physics-based simulation platform for scalable generation of diverse training packing trajectories and evaluation of their physical outcomes. PackLab-VLM is a packing-specialized MLLM that understands the evolving object and container states to jointly select objects and predict placements in a closed-loop manner. PackLab-Bench provides standardized packing scenarios at multiple difficulty levels for systematic evaluation. Extensive experiments demonstrate that, on average, PackLab-VLM outperforms conventional packing heuristics, traditional reinforcement learning methods, and general-purpose MLLMs across object sets and container configurations, highlighting the potential of MLLMs for long-horizon robotic packing. The code, model, dataset, and benchmark are available at https://github.com/Correr-Zhou/PackLab .

0.33

Low-Resolution Perception for Robotic Packing

cs.RO ·2026-08-26 ·Giuseppe Fabio Preziosa, Federico Vignoni, Chiara Castellano, Marco Faroni, Andrea Maria Zanchettin +1 more
published similarity 0.64
Abstract · 6 pages, 5 figures. Accepted to IFAC World Congress 2026

This work tackles the problem of scalable perception for robotic packing with low-cost, low-resolution depth sensing. We propose a framework where reconstruction cues drive next-view selection and grasp evidence updates a per-object stability estimate, jointly deciding what to acquire next and when to grasp. During the reconstruction, a low-resolution Next Best View (NBV) strategy explicitly avoids redundant views while preserving task-relevant geometry. We validate the approach in two steps: (i) an ablation study of the utility function under very low resolution, and (ii) a full end-to-end evaluation across policies, showing how low-resolution perception is a practical, scalable option for robotic packing.

0.35