CS Paper Radar

Hybrid Roller-Jamming Gripper for Object Acquisition and Retention Under Pose Uncertainty

Yijie Ren, Guillaume Gourmelen, Hiroyasu Iwata

cs.RO ·submitted 2026-08-21 10:33 UTC · v1
published

Abstract

In household manipulation, pose uncertainty often results in off-centre or partial initial contact, making reliable object acquisition difficult. Roller-based grippers can actively draw objects inward but often provide limited post-capture stability, whereas granular-jamming grippers require sufficient contact before jamming to achieve strong retention. This paper presents a hybrid roller-jamming gripper that integrates active object intake and post-capture retention within a single gripper. The proposed gripper uses inward roller rotation to increase contact and draw the object toward the gripper centre, followed by vacuum-induced granular jamming to stiffen the rollers and stabilise the grasp. The paper also presents a simplified geometric analysis of the gripper and a bench-level characterisation of the prototype's force capability. The gripper prototype was mounted on a 7-DoF robotic arm and evaluated using eight test objects. Furthermore, controlled planar position and orientation offsets were applied, with each condition repeated three times. The main evaluation comprised 840 grasp trials, including 216 planar-offset trials and 624 orientation-offset trials. Overall, the gripper succeeded in 812/840 trials: 215/216 planar-offset trials and 597/624 orientation-offset trials. The ablation evaluation comprised 162 trials on three objects. The roller-only and jamming-only conditions achieved 54/81 and 24/81 successes, respectively, showing their different contributions. These results provide initial mechanism-level evidence that hybrid roller-jamming is a promising strategy for improving acquisition and retention after imperfect first contact.

Comment
11 pages, 16 figures, under review
Journal ref
IEEE Access ( Volume: 14) 2026
DOI
10.1109/ACCESS.2026.3738462

Closest papers

Nearest neighbours by meaning across the whole index.

A Support-Enhanced Granular-Jamming Gripper for RL-based Grasping with Continuum Manipulators

cs.RO ·2026-09-24 ·Danyu Liu, Tianlin Zhang, Wei Chen, Wei Tang, Kecheng Qin +1 more
hot direction similarity 0.68
Abstract · 8 pages, 10 figures

Continuum manipulators provide dexterous motion in confined spaces, but structural compliance, hysteresis, and load-dependent deformation leave residual position and orientation errors that can undermine reliable contact with rigid grippers. To address this limitation, this paper presents a lightweight support-enhanced granular-jamming gripper tailored to a continuum manipulator. The gripper maintains compliance before jamming while establishing a direct load path to the continuum manipulator tip after jamming. To improve its grasping performance, we systematically designed membrane materials, particles, filling ratios, and the internal support structure, and further identify geometry-dependent grasp boundaries with respect to contact offset and object shape. Building on these results, we construct a physical manipulation system integrating the continuum manipulator, granular-jamming gripper, visual feedback, tendon actuation, and pneumatic control. We then train a reinforcement-learning-based reaching controller in a randomized simulation and deploy it on the physical system, demonstrating how positioning control and contact level mechanical adaptation can complement each other in a modular grasp-and-release task. By introducing an adaptive structure that relaxes the need for highly accurate modeling and positioning control, this work explores a design paradigm that integrates physical and embodied intelligence.

0.55

SimTO-Robust: Automated Design of Soft Grippers Robust to Grasp Pose and Object Geometry

cs.RO ·2026-10-29 ·Kurt Enkera, Joshua Pinskier, Marcus Gallagher, David Howard
similarity 0.68
Abstract

Robotic grippers operating in unstructured environments must robustly grasp objects of different shapes and sizes despite perception and positioning errors. Soft grippers that can achieve this robustness through intelligent mechanical design rather than sophisticated control software offer a promising solution. However, no existing computational design framework explicitly optimises soft gripper morphology for robustness across object geometries and grasp poses. We introduce SimTO-Robust, a generalisation of simulation-driven topology optimisation (SimTO) that simulates grasps across multiple objects and poses and aggregates their contact forces to guide gripper morphology optimisation. We generate 6,646 designs and physically evaluate 24 of them alongside 10 specialised SimTO designs, two rigid baseline grippers, and a baseline generalist soft gripper produced using conventional topology optimisation. All 37 grippers are tested in a pick-and-place task involving five feature-rich objects and six grasp poses, with external disturbances of increasing magnitude applied during the task. On average, SimTO-Robust designs complete pick-and-place more reliably than specialised SimTO designs and the rigid baselines. The best SimTO-Robust designs also withstood more of the applied disturbances than any other tested gripper. These results show that incorporating diverse grasp conditions into simulation-driven topology optimisation is a simple and effective approach to improving real-world soft gripper robustness. More broadly, they show that robust robotic grasping can be achieved through intelligent mechanical design rather than sophisticated sensing and control.

0.24

Koala Gripper: Co-designing Robotic Grippers and Data-Capture Devices for Scaling Dexterous Manipulation Learning

cs.RO ·2026-08-20 ·Amar Hajj-Ahmad, Zubin Kremer Guha, Tim Fofonoff, Zhi Ern Teoh, Ciarán T. O'Neill +6 more
similarity 0.67
Abstract · Paper website: http://koalagripper.rai-inst.com Paper video: http://www.youtube.com/watch?v=ZoygFCWAVhg

As the demand for larger manipulation datasets grows, handheld robotic gripper data collection and the associated gripper designs become more vital. Current data collection device designs trend towards matching the morphologies of existing robotic grippers, sacrificing ergonomics and manipulation performance. In this paper, we propose a co-design framework that guides the simultaneous development of both data collection and robotic execution devices by weaving both platform constraints into the design process. Through this workflow, we present the Koala Gripper system, a data capture device and robotic gripper platform that improves dexterity and grasp capability compared to parallel jaw grippers while preserving scalability and ease-of-use. The design introduces a novel force-optimized finger/trigger linkage mechanism with directional reflected mass characteristics, a unique monolithic dual-thumb, and user-centered ergonomic design. The design's actuated robotic fingers are backdrivable, with effective mass on the order of tens of grams. We show that these grippers are capable of secure grasps over a wide range of objects, forceful tool use, and precise singulation. We further validate the platform by deploying it with an end-to-end data collection and policy execution pipeline that highlights its capabilities through learning from demonstration. More information available at http://koalagripper.rai-inst.com

0.47

Gripper-Aware Automatic Dense Packing of Irregular Objects

cs.RO ·2026-09-18 ·Tianhao Qin, Connor McCann, Berk Calli, Jing Xiao
publishedbenchmark similarity 0.66
Abstract · Accepted at ISRR 2026

Automatic dense packing is widely desired in warehouse operations but remains a fundamental challenge in robotic manipulation. Existing work on irregular-object packing largely targets simulation with idealized contact, treating the object as an isolated rigid body. The gripper often enters as a discrete, post-hoc feasibility check, if considered at all, and the perception and contact drift accumulated during execution are not addressed. We present a closed-loop pipeline that integrates perception, gripper-aware placement optimization, and force-guided execution on a real manipulator. The optimizer represents the object together with the gripper as a single composite body of hierarchical sphere trees. It searches over five degrees of freedom on a GPU within a CMA-ES framework, with the vertical coordinate grounded analytically against the current heightmap. During execution, a force-monitored vertical descent stops on first contact. A post-release consolidation push then closes the residual lateral clearance that gripper-aware planning leaves behind. The container is re-perceived between placements so that drift does not accumulate. We validate the system on a Franka Emika Panda robot packing a 3D-printed set of flat, curved, and concave objects, and a YCB object subset. An ablation study isolates the contribution of gripper-aware optimization, the consolidation push, and mesh-derived geometry to end-to-end success, achieved density, and computational cost. We further benchmark against the heightmap-minimization method as a baseline representative of prior irregular-object packing work.

0.31

Active Surface-Driven Reconfigurable Gripper: Robust Grasping and Sequential Manipulation of Thin Objects

cs.RO ·2026-08-27 ·Ziyi Zheng, Keqi Zhu, Hao Wu, Yanzhe Wang, Huixu Dong
published similarity 0.66
Abstract · Accepted by RSS2026

Robotic grippers face substantial challenges in grasping and manipulating thin objects. Most existing grippers rely on highly precise approach and grasp motions, which limits robustness and reduces applicability. This paper explores thin-object grasping using books as a representative example. Here, we propose a novel solution that integrates an active surface with underactuated compliance to achieve stable grasping of thin objects without complex control. First, an underactuated gripper with an active surface is designed. The active-surface thumb performs in-hand repositioning of the target book without requiring adjustments of the robot arm or the other fingers, while the underactuated fingers establish compliant contact conditions with the environment, and the reconfigurable structure enables reliable grasping of books under different configurations. Second, we establish a kinematic model of the gripper, and determine the initial grasp postures for two representative scenarios (books lying flat on a desktop and books vertically packed in a shelf). Third, by analyzing the physical model of a book lying on a table and its interaction with the gripper and the environment, we systematically optimize the structural parameters and grasping strategy. Finally, extensive experiments validate the effectiveness of the proposed gripper and strategy. The results demonstrate strong robustness and adaptability when grasping thin objects placed flat (including books, paper, fabric, plastic film, and mouse pad), as well as a high success rate when grasping vertically packed books. Moreover, the proposed gripper can reliably complete long sequential "grasp-place" tasks.

0.21

ARTiS: An Adaptive Robotic Gripper for Enhanced Tool Manipulation in Disassembly Applications

cs.RO ·2026-09-03 ·Roman Mykhailyshyn, Yukiyasu Domae, Kensuke Harada
top venue similarity 0.65
Abstract

Grasping and holding tools while using them presents a considerable challenge not only for robots but also for humans. Such a challenge is particularly noticeable in processes involving assembly and disassembly, where efficiency and consistency depend on performing rapidly adaptive tasks. Nonetheless, contemporary robotic grasping technologies that can securely manipulate tools during operation frequently have significant constraints. In this paper, introduce ARTiS (Adaptive Robotic Tool Gripper in Disassembly Systems), a novel gripper that combines the adaptability of soft grippers, the dexterity of anthropomorphic hands, and the robustness of rigid mechanisms with a soft palm and fingertips. This unique combination makes it possible to hold tools securely in a variety of situations through using active jamming in the palm and fin-ray adaptation in fingertips. Furthermore, high finger dexterity is achieved through the seven degrees of freedom design, which enables the fingertips to orient to any surface, both for automated solutions and collaborative tasks. A comprehensive evaluation was conducted using a range of conventional disassembly tools to assess the gripper's compliance, durability, and functional versatility. More information, hardware instructions, and videos at https://romanmykhailyshyn.github.io/artis/

0.30

Control Architecture for Safe Grasping of Fragile Objects Using a Coarse Position-Controlled Gripper

cs.RO ·2026-09-11 ·Marko Pavlic, Moritz Geier, Timo Markert, Darius Burschka
published similarity 0.65
Abstract · Accepted for IEEE IROS 2026 publication

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

0.28

Grasping by interconnection: robust closing motions from coarse object templates

cs.RO ·2026-09-16 ·Julien Vanderheyden, Guillaume Drion, Fulvio Forni, Pierre Sacré
similarity 0.63
Abstract

Dexterous robot hands must often grasp objects whose shape, size, and pose are known only approximately. Grasp planners typically require accurate object models or correct errors with feedback, but how much inaccuracy a closing motion can tolerate on its own remains unclear. To address this question, we designed a motion planner based on four principles: a coarse template of the object, human grasp types, an object-centric interaction, and compliant, sliding contacts instead of prescribed contact points. This paper presents the planner, implemented through virtual model control, and its evaluation on a Shadow Dexterous Hand. Without feedback, the planned closing motions tolerated size errors of about 1cm and pose errors of several centimeters and tens of degrees, a wider range than a state-of-the-art data-driven planner in 25 of 27 tested conditions. They also grasped 82.5% of 80 everyday objects and succeeded within an autonomous pipeline. Robustness can thus be designed into the closing motion itself, rather than left only to feedback. This planner opens a path toward reliable manipulation in uncertain settings, which we will pursue by combining it with adaptive feedback control on the physical hand.

0.24