CS Paper Radar

Freeform Programmable Liquid Crystal Elastomers via Monolithic Integration of Co-Optimization and 4D-Printing

Yibo Wang, Asad Farooq Ahmed, Weichen Li, Weiyun Xu, Xiaojia Shelly Zhang

cs.CE math.OC ·submitted 2026-10-23 05:32 UTC · v1

Abstract

Liquid crystal elastomers (LCEs) are active materials capable of large, reversible thermally induced actuation, offering significant potential for applications such as artificial muscles and soft robotics. However, their broader deployment is hindered by the lack of a unified design-to-fabrication framework, the strong coupling among geometry, director fields, and manufacturing constraints, and the difficulty of reliably translating complex designs into physically realizable architectures. Here, we present an autonomous and monolithic integration of co-optimization and 4D printing that enables the end-to-end design-to-realization of versatile programmable LCE architectures with superior precision, complexity, and versatility. The proposed framework establishes a unified design strategy that co-optimizes the freeform multilayer geometry and fully continuous layer-specific director distributions, and subsequently translates the optimized fields into fabrication-ready DIW toolpaths through an automated manufacturing-aware pipeline. To bridge computation and realization, we develop an optimization-centered 4D printing approach with automated, fabrication-aware toolpath generation tailored for direct ink writing of LCEs. With the proposed design-to-fabrication paradigm, we experimentally realize architectures that exhibit complex, non-intuitive thermo-mechanical behaviors. Experiments achieve highly challenging prescribed functionalities beyond the reach of intuition-based approaches and show excellent agreement with numerical simulations across all samples. This work establishes a generalizable inverse design and physical realization of freeform programmable LCE systems, enabling function-oriented and optimization-driven intelligent LCE applications for next-generation soft robotic and responsive material engineering.

Closest papers

Nearest neighbours by meaning across the whole index.

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.63
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14

Print-Aware Synthesis and Physical Design Methodologies for 3D-Printed Microfluidic Biochips

cs.ET ·2026-08-17 ·Yushen Zhang, Tsun-Ming Tseng, Ulf Schlichtmann
published similarity 0.60
Abstract · Accepted for publication in the 2026 IEEE Computer Society Annual Symposium on VLSI (ISVLSI)

Microfluidic devices are widely used in diagnostics, chemical synthesis, and biological analysis, but their development often depends on complex fabrication and design processes. Resin-based three-dimensional (3D) printing has emerged as a promising alternative to conventional microfabrication because it enables low-cost, rapid prototyping of complex multi-layer structures. However, the practical realization of 3D-printed microfluidic biochips remains challenging due to manual and expertise-intensive design workflows, the rigid nature of commonly used printing materials, and fabrication inaccuracies such as over-curing that distort internal features and may block narrow channels. In this paper, we present a cohesive design automation framework for 3D-printed microfluidics that addresses these challenges across both device design and fabrication. The framework combines interactive design tools, automated synthesis methods for functional 3D microfluidic devices, techniques for developing low-cost 3D-printed mixers, and design-for-manufacturing strategies to improve print fidelity on low-cost resin printers.

0.32

3D-VASE: Volumetric-Aware Scalable and Efficient Multi-Layer Design Synthesis for 3D-Printed Microfluidics

cs.ET ·2026-11-17 ·Yushen Zhang, Jiashuo Chen, Tsun-Ming Tseng, Ulf Schlichtmann
published similarity 0.59
Abstract · Accepted for publication in the 32nd Asia and South Pacific Design Automation Conference (ASP-DAC 2027)

Additive manufacturing (3D printing) enables complex multi-layer microfluidic devices, but the physical synthesis of passive-flow designs remains a key bottleneck. In such systems, designers must encode timing synchronization and target dosing directly into channel geometry, even though the available routing space across multiple 3D layers is often highly congested, which makes scaling to complex designs difficult. Existing approaches formulate placement, routing, and fluidic constraints as a single monolithic optimization, leading to combinatorial explosion and poor performance on complex designs. This paper presents a volumetric-aware two-stage synthesis framework that decouples global structure from routing detail. A Mixed-Integer Programming (MIP) model first computes a compact multi-layer placement, followed by a dynamic 3D routing engine that enforces timing and volumetric constraints during path construction. To further improve routability in dense layouts, we introduce a hierarchical conflict resolution strategy combining local rip-up-and-reroute with controlled global expansion. Experimental results show that, under timing and volumetric constraints, 3D-VASE consistently improves synthesis speed and, in most test cases, also improves layout quality. Notably, for difficult large-scale cases where prior methods often failed to return any solution within the time limit, 3D-VASE produces feasible high-quality layouts within practical runtimes. These advances enable fast, iterative design-space exploration for complex 3D-printed microfluidic systems.

0.33

Manufacturing Complex Airtight Soft Pneumatic Actuators for Soft Robotics: Process Evaluation and Optimization

cs.RO ·2026-08-13 ·Mohammed Abboodi
published similarity 0.59
Abstract

Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications

0.20

Optimization-Based Path Planning for Industrial Manipulators: Experimental Validation in Additive Manufacturing

cs.RO math.OC ·2026-11-10 ·Shiva Ganesh Murali, Valentin Bhend, Deepak Ingole, Gabriele Fadini, Alisa Rupenyan
similarity 0.57
Abstract · Submitted for the review in ECC 2027

Robotic additive manufacturing requires joint paths that reconcile robot feasibility with process-specific geometry. We develop an offline optimization-based path planner that combines joint-path regularity and self-collision penalties with process costs and constraints, so that a new process enters through its own reference, residuals, and tolerances. Full-path and boundary-coupled chunked optimization handle references of different lengths. Iterative Weight Tuning (IWT) determines the cost weights from the gaps between Key Performance Indicators (KPIs) and their targets. In carbon-fiber winding and robotic 3D printing, the planned paths meet the geometric tolerances and all KPI targets, and both paths are executed on a UR10e, without extrusion for printing, with joint-level tracking recorded during execution.

0.28

X-Hinges: 3D Printing Self-Sensing Compliant Mechanisms for Continuous and Multi-DOF Motion Sensing

cs.HC ·2026-09-10 ·Xiang Chang, Haiyang Yan, Stefanie Mueller, Jiaji Li
top venue similarity 0.54
Abstract · Accepted at ACM UIST 2026. 15 pages, 24 figures. Author's accepted manuscript

We present X-Hinges, a design and fabrication method for self-sensing compliant mechanisms based on multi-material FDM 3D printing. By co-printing two conductive filaments of different conductivities within a compliant body, we embed resistive sensing elements directly during fabrication without post-assembly, enabling continuous motion sensing across multiple degrees of freedom in a single print. The structure supports three degrees of freedom, each equipped with a dedicated sensing element configuration for multi-DOF motion estimation. We develop a precision data acquisition system and data-driven regression models that enable continuous, real-time motion sensing. We also introduce an interactive design tool for customizing the geometry, mechanical properties, degrees of freedom, and sensing configurations of X-Hinges. The tool also supports augmenting existing 3D models with self-sensing structures, endowing ordinary objects with continuous multi-DOF sensing capabilities. Finally, we present a set of application examples demonstrating the capability of X-Hinges for fabricating personalized interactive interfaces.

0.47

A Physics-Based Closed-Loop Robotic Bioprinting Framework Towards Volumetric Muscle Loss Treatment

cs.RO ·2026-09-10 ·Omid Rezayof, Jerin T. Andrews, Ehsan Zobeidi, Ali Ghasemkhani, Meenakshi Kamaraj +3 more
published similarity 0.54
Abstract · This paper has been accepted for publication and presentation in 2026 IEEE/RSJ International Conference on Intelligent Robots and Systems (I…

Robotic bioprinting and Direct Ink Writing (DIW) are being explored towards the treatment of Volumetric Muscle Loss (VML). While previous studies have shown the importance of proper parameter selection on the print outcome, existing approaches often rely on time- and material-intensive design of experiments methods, or require large, well-curated datasets for training machine learning models. In this paper, we propose a physics-based closed-loop robotic bioprinting system capable of near real-time parameter adaptation. The system integrates a 3D point cloud camera and fully autonomous vision-based algorithms to provide quantitative evaluation of printed constructs. This evaluation is fed into a controller that adjusts printing parameters to achieve a desired bead thickness. To assess the framework's performance, four experimental configurations were tested, each repeated three times. In these tests, printing began from an arbitrary initial parameter value, and the controller was tasked with adjusting the parameters to reach the desired thickness. The system converged in all trials, achieving a tracking error below 0.5 mm within an average of 5.2 seconds from the start of printing. The low standard deviation of the converged pressure over different tests (0.04 bar on average) demonstrates robustness and repeatability. Additional experiments were conducted with the controller turned off, enabling direct comparison with open-loop DIW bioprinting, further confirming the effectiveness of the proposed closed-loop framework in achieving the desired bead geometry.

0.42

Piecewise CMC Segmentation for Fluidic Shaping

cs.GR ·2026-10-30 ·Abhinit Sati, Jacob Garrett, Valeri Frumkin, Edward Chien, Emily Whiting
similarity 0.53
Abstract

We present a novel mesh segmentation approach for the fabrication of 3D geometries using fluidic shaping. The physics of fluidic shaping gives rise to Constant Mean Curvature (CMC) surfaces due to interfacial tension between the polymer fluid used to shape the 3D structure and an immersion fluid of equal density. Our mesh segmentation algorithm partitions the mesh into a piecewise CMC surface, such that every segment is a CMC approximation to the target within a user specified tolerance. We run a CMC evolution procedure in the loop during segmentation to find physically stable CMC surfaces that can be reliably fabricated. We extract a wireframe scaffold from the seams of this segmentation and inject polymer fluid into the frame for curing. The structure cures as a single, continuous, isotropic volume, yielding nanometer scale roughness on the interior surface of each segment without the costly post-processing or smoothing that conventional state-of-the-art approaches require for comparable surface quality.

0.27