CS Paper Radar

SaddleSense: Saddle-Shaped Modules for 3D Shape Sensing with Single-Axis Off-the-Shelf Bend Sensors

Dong Heon Han, Runze Zuo, Chankyo Kim, Saima Jamal, Daniel Bruder

cs.RO ·submitted 2026-10-31 03:22 UTC · v1

Abstract

Accurate posture feedback is essential for precise control of continuum robots. Off-the-shelf bend sensors measure curvature about only one axis; without a suitable mounting arrangement, they can restrict robot motion and provide incomplete posture information. SaddleSense introduces a 3D-printed thermoplastic polyurethane (TPU) saddle-shaped lattice that holds one commercial bend sensor along each curved edge. Because each sensor flexes within its own channel rather than spanning the segment axially, the lattice converts multi-axis body deformation into sensor curvature without tying segment length to sensor length. Each four-sensor module accommodates two-axis bending, contraction, and extension while quantifying all three deformation modes across its four readings. A hybrid calibration maps the sensor readings to piecewise constant curvature (PCC) parameters using a learned model paired with a physics-based fallback for out-of-distribution inputs. We demonstrate a six-module prototype with 24 off-the-shelf bend sensors on a 430~mm continuum body. Using only each module's four local readings, the physics-based model alone achieves a tip position root mean square error (RMSE) of 29.9~mm (7.0\% of body length). The data-driven model reduces the tip RMSE to 13.2~mm (3.1\%) on held-out samples of motions similar to the training set and 15.8~mm (3.7\%) on separately recorded trials. Reducing each module from four sensors to one nearly triples the tip error.

Closest papers

Nearest neighbours by meaning across the whole index.

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.69
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Controlling Continuum Robot Shape in Enclosed Space with Embedded Sensing using IMU and Actuator Feedback

cs.RO ·2026-10-28 ·Jiahe Wang, Sultan Haidar Ali, Eric Weissman, Jiefeng Sun
similarity 0.67
Abstract · 8 pages, 7 figures

Controlling continuum robots' shape to operate in confined, enclosed environments is challenging, since it cannot rely on external observation. Existing embedded shape sensing methods, although they can provide shape reconstruction, are insufficient to enable real-time shape control due to limitations in reconstruction accuracy, computational speed, and compatibility with shape-state representation. In this work, we present an embedded shape-sensing framework that uses readily available IMU and actuator feedback to reconstruct the continuum-robot shape with a neural network, providing accurate shape feedback at $400~\mathrm{Hz}$ for physical closed-loop control. We systematically investigate four key reconstruction design choices: shape-state representation, network architecture, training objective, and sensing inputs, through more than $5{,}000$ trained models on one- and three-segment continuum robots. The selected framework achieves global shape errors of $0.9\%L$ and $1.7\%L$ (of the robot length) for the one- and three-segment systems, respectively. In closed-loop control, one-segment tip tracking achieves a $6.1\%L$ error and three-segment shape control achieves a $2.3\%L$ global shape error, whereas IMU--PCC reconstruction using the same uncompensated measurements fails. Enclosed-space experiments further demonstrate operation without external observation. These results provide a practical framework for translating readily available embedded sensing into high-rate feedback for continuum robot closed-loop control.

0.34

Capstan-driven Continuum Surgical Robot: Design, Modeling, and Perception

cs.RO ·2026-08-13 ·Gang Zhang, Yufu Qiu, Junyan Yan, Wenhui Zeng, Wenlong Lu +1 more
similarity 0.66
Abstract

Shape and force sensing have long been critical bottlenecks in the development of compact capstan-driven continuum surgical robots, primarily due to the difficulty of obtaining cable tension information within the confined capstan assembly. To overcome these challenges, this paper presents an integrated design-modeling-sensing approach based on the concept of actuation-perception co-design. A compliant element is introduced into the motor mounting bracket of the drive system, enabling micro-deformation under the cable reaction force and thereby allowing real-time cable tension measurement without occupying the compact capstan space. To address the modeling complexity arising from unconventional joint configurations introduced by the spatial cable routing strategy, a parallel computation framework based on a multibody short-thick-beam model is proposed, which captures shear effects in short beam segments and synergistic multi-cable interactions while achieving real-time performance. Building on this framework, stable shape and force sensing is achieved by incorporating a proximal multi-axis force/torque sensor as an additional measurement anchor. Following this design-modeling-sensing framework, capstan-driven continuum surgical robots with single- and dual-segment configurations are developed. Experimental results validate the proposed framework in both single- and dual-segment continuum robots, demonstrating real-time tip pose estimation together with contact force and location perception. By enabling cable tension feedback without compromising the compact capstan architecture, the proposed framework makes integrated perception feasible for capstan-driven continuum surgical robots.

0.04

Tendon-Driven Continuum Robot with Modular Stiffness and In-Situ Self Pose Estimation

cs.RO eess.SY ·2026-09-14 ·Guo Ning Sue, Zheng Cao, Junzhe Hu, Xiangyun Bu, David Quinn +3 more
similarity 0.66
Abstract

Continuum robots enable smooth shape morphing and safe interaction in confined environments. However, most existing systems are task-specific and depend on external sensing infrastructure, limiting their adaptability and real-world deployment. This paper presents a self-contained modular continuum robotic platform that combines mechanical reconfigurability with onboard pose estimation. The robot is constructed from interchangeable continuum joints with analytically precomputed stiffness, allowing rapid assembly and direct programming of the robot shape. Proprioceptive sensing is achieved using magnetic sensors and a modular learning-based framework, where a single model is trained per joint and reused across configurations. The system is experimentally validated in real world, demonstrating self-sensing capabilities and adaptation without external tracking.

0.33

Reliable Piezoresistive Strain Sensing Through Physical Limits and Uncertainty Monitoring

cs.RO ·2026-08-16 ·Carmen Ballester, Víctor Muñoz, Dorin Copaci, Dolores Blanco
similarity 0.62
Abstract

Soft piezoresistive strain sensors are one of the most common sensing solutions for wearable and soft robotic applications due to their flexibility and compliance. However, their resistance response is nonlinear and hysteretic, and a sensor can be pushed past its calibrated workspace or misbehave inside it, carrying that error into a decision or control loop. Probabilistic regressors track confidence but ignore those limits. A predictive mean can look unremarkable even when the reading comes from a sensor outside its admissible range or already failing internally, so a confident-looking estimate is not the same as a trustworthy one. This paper proposes a reliability framework pairing a physics-informed probabilistic inverse model, built on physics-guided input features, with a risk factor fusing uncertainty with strain and strain-rate limits into a three-state monitor. Tests on a Nitinol wire and a silver-coated polyamide thread with a Gaussian Process raised fit scores to 0.90-0.95 (RMSE 0.26%-0.15%) and a 96% empirical coverage against the 95% target. The monitor caught 95% of out-of-range and 100% of abnormal conditions while staying reliable under nominal operation. A sensor that reports confidence alongside its estimate lets a system withhold action instead, since it needs no labeled failure examples, which are hard to collect for soft materials.

0.04

OpenTac: An Open Ecosystem for Customizable, Scalable, and Transferable 3D Tactile Sensing

cs.RO eess.SPeess.SY ·2026-10-22 ·Ariel Slepyan, Geeta Chandra Raju Bethala, Jiafeng Gu, Anagha Rajendra Dangle, Yinzhe Zhou +10 more
code/data similarity 0.61
Abstract · 15 pages, 15 figures. Project website, open-source hardware and software, and demonstration videos: https://opentac.github.io

We present OpenTac, a novel sensor and a full-stack ecosystem for tactile skins that are highly customizable, scalable, and readily deployed in downstream robot control and learning applications. Our core contribution is twofold. First, we develop a scalable resistive tactile skin with a structured deformable overlay that converts tangential loading into spatially varying pressure. Differential responses across neighboring "taxels" support decoding of local shear vectors, and the common-mode response encodes normal force. Second, we provide a highly customizable sensor design tool that is able to automatically generate fabrication files for these tactile skins from 2D outlines and developable 3D surfaces, including from abstract descriptions such as text. We develop an ecosystem around the OpenTac sensor, including the CAD design tool, a sensor simulator, cross-sensor transfer, and fast/adaptive data acquisition. We demonstrate the broad applicability of the OpenTac-CAD sensor design tool by designing and fabricating more than 30 sensors across a variety of robot embodiments. We characterize the three-dimensional tactile fields produced by OpenTac with a commercial, high-precision force/torque sensor. We demonstrate the broad applicability of 3D tactile sensing across contact-rich feedback control and manipulation policy learning on four real-world robot embodiments. Additionally, adaptive acquisition enables kilohertz-rate partial readouts, and our readout circuitry enables high dynamic range (HDR) acquisition, measuring, for example, a 3.7 kg weight stack and a 20 g weight on the same sensor in the same frame. We provide all hardware, software, and result videos at opentac.github.io

0.21

Constraint-Aware Physics-Informed Neural Networks for Static Shape Estimation of Co-Manipulative Continuum Robots

cs.RO cs.LG ·2026-08-26 ·Rana Danesh, Pari Qarehdaghi, Farrokh Janabi-Sharifi
similarity 0.61
Abstract

Static shape estimation of co-manipulative continuum robots (CCRs) is challenging because the continuum arms and manipulated flexible object form a closed chain that must satisfy both static equilibrium and geometric loop-closure constraints. This paper presents a constraint-aware physics-informed neural network (PINN) for static shape estimation of a tendon-driven CCR modeled using the geometric variable strain formulation. The proposed method incorporates a projected static equilibrium residual and a configuration-level geometric residual to enforce the governing mechanics and closed-chain geometry. In simulation, the PINN is compared with a purely data-driven artificial neural network (ANN) under limited and noisy training data. With 140 samples and 50% label noise, the PINN reduces the relative configuration error, equilibrium residual, and closed-chain residual by 67.88%, 67.35%, and 88.06%, respectively. Using the full dataset, the PINN achieves 0.1597% relative configuration error with an inference time of 0.1773 ms, compared with 17.97 s for an iterative nonlinear solver. Experimental fine-tuning reduces the marker RMSE from 2.657 mm to 0.497 mm and increases R2 from -0.788 to 0.937. These results demonstrate accurate, physically consistent, and computationally efficient static shape estimation of closed-chain CCRs.

0.17

Flexibility-Aware Robotic Manipulation: Deformation Estimation, Kinematics, and Control via Distributed Inertial Measurement

cs.RO ·2026-10-30 ·Amir Hossein Barjini, Sadeq Yaqubi, Pauli Mustalahti, Jouni Mattila
similarity 0.60
Abstract

Flexible robot links challenge the rigid-body assumption, making joint measurements alone insufficient for accurate manipulation. This paper introduces a flexibility-aware manipulation framework that connects structural dynamics directly to sensing, kinematics, and control. Instead of prescribing a dense inertial measurement unit (IMU) network, the dominant vibration modes of each flexible link are first identified from response-convergence and excitation-bandwidth criteria. Under a full-rank modal observability condition, $m$ retained modes require only $m$ independent slope measurements and one reference IMU, defining the minimum observable IMU configuration. The resulting measurements are used to reconstruct the continuous link deformation, which is then incorporated into flexibility-aware forward kinematics and a deformation-informed partial differential equation-based controller. Experiments on hydraulic single- and double-link manipulators evaluate the framework. On the long-reach double-link platform, the proposed kinematics achieves end-effector root mean square errors of $0.0107$~m, $0.0194$~m, and $0.0102$~rad while using fewer sensors than the piecewise-rigid method. Closed-loop reaching experiments further demonstrate real-time integration of IMU-estimated joint states and reconstructed deformation into the proposed controller. The results show that dominant modal information can determine sensing requirements and enable real-time flexibility-aware robotic manipulation.

0.34