CS Paper Radar

Controlling Continuum Robot Shape in Enclosed Space with Embedded Sensing using IMU and Actuator Feedback

Jiahe Wang, Sultan Haidar Ali, Eric Weissman, Jiefeng Sun

cs.RO ·submitted 2026-10-28 23:32 UTC · v1

Abstract

Controlling continuum robots' shape to operate in confined, enclosed environments is challenging, since it cannot rely on external observation. Existing embedded shape sensing methods, although they can provide shape reconstruction, are insufficient to enable real-time shape control due to limitations in reconstruction accuracy, computational speed, and compatibility with shape-state representation. In this work, we present an embedded shape-sensing framework that uses readily available IMU and actuator feedback to reconstruct the continuum-robot shape with a neural network, providing accurate shape feedback at $400~\mathrm{Hz}$ for physical closed-loop control. We systematically investigate four key reconstruction design choices: shape-state representation, network architecture, training objective, and sensing inputs, through more than $5{,}000$ trained models on one- and three-segment continuum robots. The selected framework achieves global shape errors of $0.9\%L$ and $1.7\%L$ (of the robot length) for the one- and three-segment systems, respectively. In closed-loop control, one-segment tip tracking achieves a $6.1\%L$ error and three-segment shape control achieves a $2.3\%L$ global shape error, whereas IMU--PCC reconstruction using the same uncompensated measurements fails. Enclosed-space experiments further demonstrate operation without external observation. These results provide a practical framework for translating readily available embedded sensing into high-rate feedback for continuum robot closed-loop control.

Comment
8 pages, 7 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Tendon-Driven Continuum Robot with Modular Stiffness and In-Situ Self Pose Estimation

cs.RO eess.SY ·2026-09-14 ·Guo Ning Sue, Zheng Cao, Junzhe Hu, Xiangyun Bu, David Quinn +3 more
similarity 0.69
Abstract

Continuum robots enable smooth shape morphing and safe interaction in confined environments. However, most existing systems are task-specific and depend on external sensing infrastructure, limiting their adaptability and real-world deployment. This paper presents a self-contained modular continuum robotic platform that combines mechanical reconfigurability with onboard pose estimation. The robot is constructed from interchangeable continuum joints with analytically precomputed stiffness, allowing rapid assembly and direct programming of the robot shape. Proprioceptive sensing is achieved using magnetic sensors and a modular learning-based framework, where a single model is trained per joint and reused across configurations. The system is experimentally validated in real world, demonstrating self-sensing capabilities and adaptation without external tracking.

0.34

SaddleSense: Saddle-Shaped Modules for 3D Shape Sensing with Single-Axis Off-the-Shelf Bend Sensors

cs.RO ·2026-10-31 ·Dong Heon Han, Runze Zuo, Chankyo Kim, Saima Jamal, Daniel Bruder
similarity 0.67
Abstract

Accurate posture feedback is essential for precise control of continuum robots. Off-the-shelf bend sensors measure curvature about only one axis; without a suitable mounting arrangement, they can restrict robot motion and provide incomplete posture information. SaddleSense introduces a 3D-printed thermoplastic polyurethane (TPU) saddle-shaped lattice that holds one commercial bend sensor along each curved edge. Because each sensor flexes within its own channel rather than spanning the segment axially, the lattice converts multi-axis body deformation into sensor curvature without tying segment length to sensor length. Each four-sensor module accommodates two-axis bending, contraction, and extension while quantifying all three deformation modes across its four readings. A hybrid calibration maps the sensor readings to piecewise constant curvature (PCC) parameters using a learned model paired with a physics-based fallback for out-of-distribution inputs. We demonstrate a six-module prototype with 24 off-the-shelf bend sensors on a 430~mm continuum body. Using only each module's four local readings, the physics-based model alone achieves a tip position root mean square error (RMSE) of 29.9~mm (7.0\% of body length). The data-driven model reduces the tip RMSE to 13.2~mm (3.1\%) on held-out samples of motions similar to the training set and 15.8~mm (3.7\%) on separately recorded trials. Reducing each module from four sensors to one nearly triples the tip error.

0.32

Design and Characterization of a Unified Continuum Robot Actuation Platform

cs.RO ·2026-10-14 ·Yunti Xu, Aedan Mangan, Miheer Potdar, Alex Lu, Tania K. Morimoto
similarity 0.66
Abstract

Continuum robots enable dexterous access to confined spaces in applications such as minimally invasive surgery and industrial inspection. However, their actuation systems are often custom-designed for specific robot architectures and tasks, limiting reuse across publications, institutions, and applications. This paper presents a unified actuation platform that decouples actuation hardware and software from continuum robot design. The platform provides modular actuation across continuum robot classes, scales to a large number of degrees of freedom (DOFs), and integrates with conventional serial manipulators for hybrid architectures. We validate the platform on an open-sourced surgical robotic system and experimentally characterize the actuation modules, achieving sub-millimeter translational accuracy and less than $5^\circ$ rotational error over ranges of $30$~mm and $180^\circ$, respectively. We further demonstrate the platform in two surgical use cases: teleoperation of a continuum camera in a constrained environment and bimanual manipulation using $2.53$~mm concentric-tube-robot-based forceps alongside a conventional wristed instrument. All hardware designs and ROS-based software are open-sourced to facilitate reuse and further research in continuum and surgical robotics.

0.31

Riemannian Optimization-based Whole-body Obstacle Avoidance for Mobile Continuum Robots in Cluttered Environments

cs.RO ·2026-11-04 ·Duo Tang, Ping Deng, Sophie Armanini, Yajing Shen, Toshio Fukuda +2 more
similarity 0.66
Abstract

Inspired by the coordination of global motion and local shape adaptation in snakes, elephant trunks, and octopus arms, we propose a unified planning and control framework for mobile continuum robots in cluttered and confined environments. Existing approaches often address high-level path planning and local motion control separately, limiting coordinated base-arm motion, kinematic consistency, and collision avoidance. Our framework integrates long-horizon trajectory planning with real-time geometric refinement under kinematic and environmental constraints. The global layer combines A* search with minimum-jerk planning to generate smooth reference trajectories. The local layer uses a geometry-consistent inverse kinematics solver and Riemannian optimization to coordinate mobile-base motion and continuum deformation while avoiding obstacles. We evaluate the framework through simulated pipe-traversal tasks with multiple baseline planners and real-world experiments involving navigation among dense obstacles and manipulation in confined spaces. Results demonstrate improved motion consistency, feasibility, and adaptability, supporting coordinated whole-body motion of mobile continuum robots in constrained environments.

0.27

Real-Time Shape Control of Multi-Segment Soft Robotic Arms Using Koopman Operators with Global and Local Observables

cs.RO eess.SY ·2026-09-02 ·Jiahe Wang, Eron Ristich, Sultan Haidar Ali, Eric weissman, Lei Zhang +3 more
similarity 0.66
Abstract · 18 pages, 14 figures, submitted to TRO

Multi-segment soft robotic arms can continuously reconfigure their body shapes for safe interaction, but tip control alone is insufficient for constrained-space tasks. Therefore, shape control is a more important task for multi-segment soft arms than tip control, but remains challenging due to the high dimensionality and nonlinear dynamics of continuum deformation. In existing work, shape control accuracy is defined by the error in the global frame (global shape error). For multi-segment soft arms, using only global shape error as the control objective is insufficient, as segment coupling, gravity-induced loading, and inertial effects become more significant. This difficulty increases with the number of segments. In this paper, we present a Koopman-based model predictive control framework that combines global and local observables, enabling real-time shape control on multi-segment soft robotic arms. The framework is evaluated through numerical and physical experiments. Numerical experiments demonstrate the scalability of the proposed controller by achieving shape control on robots with up to 10 independently actuated segments. The physical experiments demonstrate that the controller is capable of (1) real-time shape control of 3- and 5-segment robotic arms with tip speeds up to 0.6 m/s, (2) robust tracking without retraining, including distal payloads up to 400~g and recovery from a 7~N lateral disturbance, and (3) the potential for future inspection applications through a confined-space demonstration. These results demonstrate that the proposed framework enables dynamic, scalable, and accurate real-time shape control on multi-segment soft robotic arms.

0.35

Constraint-Aware Physics-Informed Neural Networks for Static Shape Estimation of Co-Manipulative Continuum Robots

cs.RO cs.LG ·2026-08-26 ·Rana Danesh, Pari Qarehdaghi, Farrokh Janabi-Sharifi
similarity 0.65
Abstract

Static shape estimation of co-manipulative continuum robots (CCRs) is challenging because the continuum arms and manipulated flexible object form a closed chain that must satisfy both static equilibrium and geometric loop-closure constraints. This paper presents a constraint-aware physics-informed neural network (PINN) for static shape estimation of a tendon-driven CCR modeled using the geometric variable strain formulation. The proposed method incorporates a projected static equilibrium residual and a configuration-level geometric residual to enforce the governing mechanics and closed-chain geometry. In simulation, the PINN is compared with a purely data-driven artificial neural network (ANN) under limited and noisy training data. With 140 samples and 50% label noise, the PINN reduces the relative configuration error, equilibrium residual, and closed-chain residual by 67.88%, 67.35%, and 88.06%, respectively. Using the full dataset, the PINN achieves 0.1597% relative configuration error with an inference time of 0.1773 ms, compared with 17.97 s for an iterative nonlinear solver. Experimental fine-tuning reduces the marker RMSE from 2.657 mm to 0.497 mm and increases R2 from -0.788 to 0.937. These results demonstrate accurate, physically consistent, and computationally efficient static shape estimation of closed-chain CCRs.

0.17

Collocated Shape Regulation for Soft Robots

cs.RO eess.SY ·2026-09-23 ·Pietro Pustina, Ebrahim Shahabi, Daniel Feliu-Talegon, Alessandro De Luca, Cosimo Della Santina
hot direction similarity 0.65
Abstract · 33 pages, 22 figures

Controlling the shape of a continuum soft robot typically requires an accurate dynamic model and actuation of all degrees of freedom. We show that regulating only the actuated coordinates, through collocated shape control, achieves provably stable convergence of those coordinates and, under an explicit compatibility condition, of the entire robot shape. While collocated control is a cornerstone of high-performance motion control in rigid robotics, extending this formulation to continuum soft robots has remained challenging due to the complexity of their dynamics. We present the first general framework for collocated control of continuum soft robots and derive a unified family of controllers, including PD, PID, PsatID, and their counterparts with compensation and cancellation components. The framework unifies existing approaches while introducing new controller designs. In particular, we develop three classes of PD and PID like regulators with local, semi-global, and global stability guarantees, and provide rigorous convergence analyses for each. Extensive experimental validation demonstrates the effectiveness of the proposed methods across different model discretizations and controller parameters. The resulting framework provides practical design guidelines for selecting and implementing controllers with known stability guarantees, without requiring a complete dynamic model of the robot

0.33

Magnetic based In-situ Self 3D Pose Estimation for a Modular Soft Tendon-Driven Continuum Robot via IMU-Fusion

cs.RO eess.SPeess.SY ·2026-09-30 ·Zheng Cao, Guo Ning Sue, Xiangyun Bu, David Quinn, Junzhe Hu +1 more
similarity 0.64
Abstract

Continuum robots are well suited for gentle manipulation because of their inherent compliance and ability to adapt to complex environments. However, their continuously deformable structure makes accurate configuration estimation challenging, particularly when external vision systems are unavailable or obstructed. In this work, we present an embedded pose sensing framework that combines inertial measurement units (IMUs) and active magnetic fields to estimate the robot configuration without relying on external cameras. The angular measurements from the IMU and magnetic-field references are fused to improve local orientation estimation and reduce accumulated orientation error during operation. This pose sensing scheme achieves an update rate of 16.7~Hz, allowing real-time feedback. The proposed system is experimentally validated through closed-loop control, where the estimated robot configuration is used to maintain the end-effector at a desired position while interacting with an object. These results demonstrate the potential of distributed magnetic--inertial sensing for real-time pose estimation and closed-loop control of continuum robots.

0.11