CS Paper Radar

Development of a Voice-Controlled Tendon-Driven Bionic Hand

Urja Kohli, Shagata Chanda, Kritika Gandhi, Charu Nigam, Aditi Surya Kamal, Pooja Bhati

cs.RO cs.HCeess.SY ·submitted 2026-08-25 23:22 UTC · v1

Abstract

The impairment of the hands can seriously affect the abilities of every individual to perform the every-day activity, so the design of stable and controllable support devices is a significant field of study. This paper is about the design and implementation of an automated bionic hand which is dedicated to the coordinated finger movement through the simplified and efficient actuation mechanism. The method that the proposed system was designed on is the tendon-based method whereby the servo motors generate the movement of the fingers, with assistance of the angular control which is calibrated. An actuation is controlled by a microcontroller that will be programmed by use of an Arduino-based microcontroller to carry out programmed gestures that include open hand, fist, pinch and half flexion. It has an interface that is voice command enabled to make it easy to interact with a Bluetooth based sender receiver architecture which offers an option of executing trained commands which are immediately converted to finger actions. To explore the motions behavior, finger coordination and control response to the input, the behavior of the experiment system is tested. The actuation of the fingers was found to take a total of about 7-8 seconds to achieve full flexion of all fingers in a sequence. The system showed repetitive and constant motion throughout several actuation cycles without loss of any apparent tension or precision of control. There was a stable grasp of objects of different shapes and sizes, which implied consistent coordination between the fingers. These findings indicate that the proposed system offers predictable and steady control behavior and has a simple and efficient mechanical and control architecture.

Comment
20 pages, 11 figures, 6 tables. Open-access preprint intended for journal or conference submission

Closest papers

Nearest neighbours by meaning across the whole index.

Design of a hybrid tendon-linkage finger with coupled and adaptive motion

cs.RO ·2026-11-09 ·Hyojae Kang, Giup Seo, Jae-Young Lee, Yeong Jae Park, Jongwoo Park +4 more
similarity 0.63
Abstract · This manuscript has been submitted for possible publication

Dexterous robotic fingers require coordinated joint motion and adaptability to object contact, while independently actuating multiple joints increases the complexity of the transmission mechanism. This paper presents a hybrid tendon--linkage robotic finger with four mechanical degrees of freedom driven by three actuators. The MCP abduction/adduction joint is driven through a bevel gear, while MCP and PIP flexion/extension are driven by separate bidirectional tendon transmissions. The DIP joint is not independently actuated but is coupled to the PIP joint through a four-bar linkage with a torsional spring and mechanical stopper. The tendon routing also introduces mechanical coupling between the MCP and PIP joints. Kinematic analysis was conducted to describe the coupled and adaptive motions, and experiments were performed to evaluate the joint motion characteristics. ArUco-based measurements showed that the coupled motion closely matched the theoretical prediction, whereas the adaptive motion was partially limited by interference between linkage components. The fabricated finger demonstrated different contact postures with cylindrical, cuboid, and irregularly shaped objects, and the mean peak fingertip force was 4.56 N. The proposed mechanism provides both coupled motion and contact-dependent adaptation without requiring an additional actuator for the DIP joint.

0.13

A Reconfigurable Dual-Opposition Architecture for Single-Hand Assembly and Manipulation

cs.RO ·2026-09-19 ·William Su, Yunosuke Nakamura, Yixiao Wang, Yitong Li, Mingrui Yu +4 more
similarity 0.62
Abstract · 9 pages, 7 figures, 2 tables

In-hand assembly is constrained by the need to maintain grasps on two separate parts while controlling their relative motion within a single hand. To enable both in-hand assembly and manipulation, we present a reconfigurable dual-opposition architecture. Specifically, to support simultaneous grasping of two parts and coordinated in-hand manipulation, four independently actuated fingers are organized into two virtual finger (VF) oppositions, with their relative configuration controlled by a reconfigurable palm. To describe hand motion and simultaneous two-object grasping configurations, a kinematic model of the fingers and palm and an object-size-conditioned workspace formulation are built. To further evaluate motion performance and assembly capability, finger-joint motion and palm tracking are characterized, and in-hand assembly is demonstrated through tasks involving grasping, alignment, fastening, and pressing. Ablation experiments further demonstrate the importance of finger abduction/adduction and palm reconfiguration for successful in-hand assembly. In simulation, the proposed hand achieves a mean continuous sphere rotation success rate of 98.6% over diameters of 40-230 mm, compared with 73.8% for the LEAP Hand. After policy fine-tuning with external disturbances, the proposed hand achieves 92.8% success under disturbances from multiple directions, compared with 45.2% for the LEAP Hand. Hardware demonstrations further show in-hand rotation of objects of different sizes using policies trained in simulation. Together, these results show that the proposed architecture supports both assembly of two separately held parts and coordinated manipulation of a single object within one hand.

0.50

GIFT: Glove-Inferred Force Transfer: Force-Aware Human-to-Robot Skill Transfer from a Wearable Sensing Glove to a Robot Hand Without Tactile Sensors

cs.RO ·2026-09-12 ·Tzach Sarusi
code/data similarity 0.59
Abstract · 7 pages, 5 figures, 1 table. Project page: https://tzahsarusi.github.io

Human-to-robot skill transfer from sensing gloves has so far relied on shared hardware: the same tactile glove worn by the demonstrator and the robot, or a learned alignment between two tactile sensors. We present GIFT (Glove-Inferred Force Transfer), a pipeline in which the interface between human and robot is a physical unit rather than a shared sensor: fingertip force is measured in newtons on the human side and estimated in newtons on the robot side. A wearable glove records finger flexion, calibrated fingertip force, and wrist orientation, while a head-mounted camera records the demonstration; no robot is present. At deployment, the robot estimates force from actuator-current residuals relative to a free-space baseline, through a calibrated mapping to newtons, so any position-controlled hand that reports motor current can serve as the deployment platform. The policy uses a glove-space state and predicts finger-position targets; the robot enters only through two calibrated adapters, a retargeting decoder and a force estimator. We evaluate GIFT on a cup grasp-and-hold task with two action-chunking policies trained on the same demonstrations, with fingertip-force inputs retained in one and zeroed in the other. In a 50-rollout evaluation with sample size and metrics fixed before scoring, both policies succeeded in all 25 rollouts. The median of the per-rollout hold-phase grip-force estimates was 53% lower with force inputs: 1.20 N versus 2.55 N (one-sided Mann-Whitney U, p<0.0001). In an observation ablation, a vision-only policy achieved 0/15 grasps, policies given hand-command state acquired the grasp, and the force inputs determined how hard the policy held. A force channel measured on the human hand thus transfers to a robot hand with no tactile hardware, through a retargeting map from five glove channels to seven robot actuators, with no sensor shared between the two.

0.32

H-PAC Hand: Control-Oriented Modeling and Tendon-Elasticity Compensation for an Underactuated Robotic Hand

cs.RO ·2026-08-17 ·Teng Yan, Jiongxu Chen, Teng Wang, Yue Yu, Qixiang Hua +3 more
similarity 0.59
Abstract · 7 pages, 6 figures. Extended preprint

Underactuated tendon-driven hands offer compact actuation and passive compliance, but tendon elongation under restoring-spring loading introduces configuration-dependent joint deviations. This paper presents H-PAC, a modular 6-actuator, 15-DoF robotic hand with a control-oriented modeling and implementation framework. A sparse analytical actuator-joint model is derived from the tendon-routing geometry, and a mechanics-based compensation model is developed to account for tendon-elasticity-induced joint errors. The proposed method is implemented in a hierarchical architecture: a host computer performs workspace-constrained posture mapping and compensation, while an ESP32 generates synchronized commands for six position-controlled servos. The same control parameters and execution strategy are used across all tasks without task-specific retuning. Monotonic servo-sweep experiments show that the compensation substantially improves joint-angle prediction. The MAE of the index DIP joint decreases from 1.15 degrees to 0.18 degrees, and all nine evaluated joints achieve an MAE below 0.23 degrees. Representative postures and grasping configurations are further executed using the same control pipeline without external joint or force sensing in the control loop. The results demonstrate a practical approach to improving posture reproducibility in compact underactuated robotic end-effectors.

0.34

A fully articulated humanoid dexterous hand with human-level joint structure enabled by linkage-based actuation

cs.RO ·2026-10-27 ·Jihao Li, Jianguo Wang, Haotian Guo, Yanzhe Wang, Guodong Lu +1 more
similarity 0.59
Abstract

Humanoid dexterous hands are a core component of embodied intelligence, enabling robots to translate high-level intent into rich and adaptive physical interaction. However, existing designs remain constrained by a persistent trade-off among anthropomorphic kinematic complexity, mechanical robustness, load capacity and control simplicity, limiting dexterous manipulation in unstructured environments. Here we present Torch-Hand, a fully articulated humanoid dexterous hand that replicates the joint structure and motion hierarchy of the human hand with 21 degrees of freedom (DOF), comprising a highly articulated five-DOF thumb and four DOF in each of the remaining fingers. The differentiated thumb integrates multi-axis CMC motion to provide broad opposition and flexible contact orientation relative to the four fingers. Unlike tendon-driven or hybrid actuation approaches, Torch-Hand adopts an entirely linkage-based transmission architecture. By integrating screw-linkage actuation, the hand achieves high grasping force and substantial payload capacity while maintaining a compact anthropomorphic form. Its actuation architecture is optimized for control tractability, with all actuators integrated within the palm and arranged in a serial-robot-like configuration that establishes a direct correspondence between motor motion and joint kinematics. This architecture mechanically decouples functional DOF to reduce unintended inter-joint motion propagation, while allowing independently addressable DOF to be actively coordinated into coupled multi-joint motion patterns during complex manipulation. Comprehensive experiments assess reachable workspace, coordinated fingertip trajectories, thumb opposition, 33-grasp taxonomy coverage, grasping force, payload capacity and task-level manipulation. These results establish Torch-Hand as a robust hardware foundation for dexterous embodied manipulation.

0.22

PACT: Pose-Robust Actuation Co-Design for Tendon-Driven Robotic Hands

cs.RO ·2026-11-03 ·Prashant Kumar, Rachael Granberry, Taylor Niehues, Andrew A. Stanley, Gabe Pirie
similarity 0.59
Abstract

Humanoid robotic hands must provide sufficient force, speed, and backdrivability within a human-scale envelope. Tendon-driven transmissions address this challenge by relocating actuators to the palm and forearm, but routing paths, moment arms, and capstan dimensions jointly determine both force capability and joint speed, so selecting them sequentially satisfies one requirement at the expense of the other. This paper presents a pose-robust actuation co-design for tendon-driven robot hands (PACT) framework that optimizes tendon routing, moment arms, and capstan dimensions under pose-dependent force requirements and drivetrain-bandwidth constraints. A feasible-force formulation enforces actuator bounds and equilibrium at all joints, while a max-min objective maximizes task-force coverage at the weakest pose. Applied to a four-degree-of-freedom finger, the framework produces an asymmetric N + 1 tendon topology using quasi-direct-drive actuators. Across eight poses, the design achieves task-force coverage of 0.88-1.00 and a predicted 5 Hz minimum isolated-joint flexion/extension bandwidth within a 70th-percentile human-size envelope. Prototype measurements deviate from predictions by up to 24.5%, primarily due to unmodeled transmission losses. These results indicate that co-designing routing with the drivetrain can meet pose-dependent force requirements without relaxing the bandwidth constraint, paving the way for human-sized robotic hands with human-level performance.

0.08

ORBIT: A Modular Multi-finger Robotic Hand Platform with Rotational Finger Reconfiguration

cs.RO ·2026-10-23 ·Benito Ribadeneira, Siqi Shang, Lillian Chin
similarity 0.57
Abstract · NA

Despite the popularity of multi-fingered robotic hands for dexterous manipulation, there is no systematic platform to compare different hand morphologies against one another. We present ORBIT (Orbital Reconfigurable Base-actuated Integrated Theta-motion Hand), a modular platform designed to enable principled exploration of multi-fingered hand morphology. The core contribution of ORBIT is a rotating knuckle mechanism, where independent fingers travel around a cylindrical palm via a belt drive. This enables ORBIT to perform quick recon- figuration (< 1 s) of finger layout without hand disassembly. ORBITs a robust system, with finger average angular velocity of 1.57 rad / s1 and a root finger force resistance of 50 N. Using a three fingers instantiation of ORBIT, we demonstrate an initial pilot grasping study, comparing anthropomorphic, isometric, and Barrett-style finger layouts across eleven objects of varied size, shape, and texture. We further demonstrate how ORBITs nonanthropomorphic orbital DOF enables the achievement of tasks that would be difficult to perform with fixed-knuckle designs, such as cube face reorientation, lid threading, and precision pinching of sub-centimeter objects. These results establish ORBIT as a viable platform for direct apples to apples comparison of multi-fingered hand morphologies for specific manipulation tasks

0.21

Design of a Fully Actuated 4-DOF Robotic Finger With Joint-Specific Hybrid Remote Actuation

cs.RO ·2026-10-07 ·Hyojae Kang, Hyun-mok Jung, Joonho Lee, Dongil Park, Hyunmin Do +2 more
similarity 0.57
Abstract · 10 pages, 10 figures. This manuscript has been submitted for possible publication

This paper presents a fully actuated 4-DOF robotic finger using a joint-specific hybrid remote-actuation architecture. The metacarpophalangeal (MCP) joint is driven by two coordinated rigid-link transmission sets, whereas the proximal interphalangeal (PIP) and distal interphalangeal (DIP) joints are independently actuated by closed-loop wire transmissions incorporating circular rolling-contact joints (RCJs). A larger transmission radius is used at the PIP joint than at the DIP joint. The RCJ wire geometry maintains the total wire-loop length during joint rotation, and the DIP wire routing is designed so that PIP motion does not affect its differential actuation for a fixed MCP configuration. The distal wire transmission, MCP linkage, and fingertip kinematics are analytically modeled. In experiments, the transmission behavior was quantitatively evaluated from the ball-screw displacements measured using ArUco-marker tracking. MCP actuation produced measurable displacements of the PIP and DIP transmission units, whereas isolated PIP and DIP actuation with the MCP fixed supported the intended mechanical decoupling between the distal transmissions. The mean peak fingertip forces under isolated MCP, PIP, and DIP actuation were 21.28 N, 9.22 N, and 5.75 N, respectively. The resulting finger postures were also examined using objects of different geometries and sizes.

0.37