CS Paper Radar

A Simple Gripper Interface for Simulator-Agnostic Cloth Manipulation

Abhilash Nayak, Franco Coltraro, Maria Alberich-Carramiñana, Carme Torras

cs.RO ·submitted 2026-09-24 10:14 UTC · v2
publishedhot direction

Abstract

This paper presents a grasping model for cloth manipulation specifically tailored to ease the deployment of robotic control methods. The model is robust, fast and easy to implement avoiding at the same time contact and friction considerations between the gripper and the cloth in favor of simple positional constraints. The gripper is described by its pose, jaw state, and an attached grasping volume. Two kinds of grasping volumes are considered: an axis-aligned box to simulate a pinch grasping and a square pyramidal volume to simulate point grasping. When the gripper closes, the discrete cloth positions lying inside this volume are selected, stored in the local gripper frame, and then transported with the gripper motion. A simple squeezing step is also included to progressively move the selected cloth positions toward the center of the grasping region, avoiding an instantaneous displacement at closure. The model can be used in any simulator as it only requires access to discrete cloth positions and a mechanism for imposing target positions as constraints. We implement our grasping model in conjunction with a constraint-based inextensible cloth simulator, where grasping is implemented as moving positional equality constraints coupled with stretch, shear, collision, and table contact projection steps. The same gripper trajectory is applied on a robot arm to fold a real piece of cloth, serving as a simple bridge between simulation and physical cloth manipulation and showcasing the realism and practicality of our idealized grasping model.

Comment
Accepted for a special session on Hybrid Intelligence at the 23rd International Conference on Informatics in Control, Automation and Robotics, 26-28 October, 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Active Surface-Driven Reconfigurable Gripper: Robust Grasping and Sequential Manipulation of Thin Objects

cs.RO ·2026-08-27 ·Ziyi Zheng, Keqi Zhu, Hao Wu, Yanzhe Wang, Huixu Dong
published similarity 0.71
Abstract · Accepted by RSS2026

Robotic grippers face substantial challenges in grasping and manipulating thin objects. Most existing grippers rely on highly precise approach and grasp motions, which limits robustness and reduces applicability. This paper explores thin-object grasping using books as a representative example. Here, we propose a novel solution that integrates an active surface with underactuated compliance to achieve stable grasping of thin objects without complex control. First, an underactuated gripper with an active surface is designed. The active-surface thumb performs in-hand repositioning of the target book without requiring adjustments of the robot arm or the other fingers, while the underactuated fingers establish compliant contact conditions with the environment, and the reconfigurable structure enables reliable grasping of books under different configurations. Second, we establish a kinematic model of the gripper, and determine the initial grasp postures for two representative scenarios (books lying flat on a desktop and books vertically packed in a shelf). Third, by analyzing the physical model of a book lying on a table and its interaction with the gripper and the environment, we systematically optimize the structural parameters and grasping strategy. Finally, extensive experiments validate the effectiveness of the proposed gripper and strategy. The results demonstrate strong robustness and adaptability when grasping thin objects placed flat (including books, paper, fabric, plastic film, and mouse pad), as well as a high success rate when grasping vertically packed books. Moreover, the proposed gripper can reliably complete long sequential "grasp-place" tasks.

0.21

Relative Contact Velocity-Controlled Hand-Object Mechanism for Dexterous Tool Manipulation

cs.RO ·2026-09-22 ·Sunyu Wang, Jean Oh, Nancy S. Pollard
hot direction similarity 0.68
Abstract

This work investigates how to enable general multi-finger robotic hands to perform the complete tool manipulation process, which entails picking up a tool, loading it into a suitable pose, and then wielding it. Inspired by human tool manipulation and mechanical design principles, we model the hand and the tool as a unified hand-object mechanism (HOM) composed of sub-assemblies. Specifically, we define a HOM as consisting of the hand, the object, and the generalized contact frames, allowing the HOM's motions to be expressed with the same set of Cartesian-space relative contact velocities, irrespective of the hand's kinematics and geometry. Then, we define a HOM's sub-assemblies as relative contact velocity and contact force constraints between fingers. Building on these definitions, we developed a lightweight and physically interpretable motion planning and contact estimation framework using least squares and a complementary filter. We evaluated our framework in simulation by teleoperating five different robotic hands. The results show that our framework enabled all five hands to execute the complete tool manipulation process, achieving dexterous behaviors even from identical, simple reference trajectories. Furthermore, the results showcase our framework's adaptability to different hands, tools, and tasks, enabled by its kinematic and geometric foundation. Please visit website for videos: \href{https://sunyuw.github.io/hom-sim/}{https://sunyuw.github.io/hom-sim/}

0.33

Grasping by interconnection: robust closing motions from coarse object templates

cs.RO ·2026-09-16 ·Julien Vanderheyden, Guillaume Drion, Fulvio Forni, Pierre Sacré
similarity 0.68
Abstract

Dexterous robot hands must often grasp objects whose shape, size, and pose are known only approximately. Grasp planners typically require accurate object models or correct errors with feedback, but how much inaccuracy a closing motion can tolerate on its own remains unclear. To address this question, we designed a motion planner based on four principles: a coarse template of the object, human grasp types, an object-centric interaction, and compliant, sliding contacts instead of prescribed contact points. This paper presents the planner, implemented through virtual model control, and its evaluation on a Shadow Dexterous Hand. Without feedback, the planned closing motions tolerated size errors of about 1cm and pose errors of several centimeters and tens of degrees, a wider range than a state-of-the-art data-driven planner in 25 of 27 tested conditions. They also grasped 82.5% of 80 everyday objects and succeeded within an autonomous pipeline. Robustness can thus be designed into the closing motion itself, rather than left only to feedback. This planner opens a path toward reliable manipulation in uncertain settings, which we will pursue by combining it with adaptive feedback control on the physical hand.

0.45

TCAM for Autonomous Deformable Manipulation: The RMC2 Champion System for WBCD 2026 Track 4

cs.RO ·2026-08-11 ·Guangrui Shen, Zhili He, Shigang Wang, Yuanjun Sun, Qing Yu
similarity 0.67
Abstract

This technical report describes the RMC2 Team's champion solution for the WBCD 2026 Track 4: Deformable Manipulation Challenge. The task requires a robot to pick a single T-shirt from a stack, load it onto a printing pallet, align the collar with a target area, and smooth the printing region, a sequence that involves single-layer separation, deformable transport, precise placement, and contact-rich surface adjustment. The competition strongly incentivizes fully autonomous execution, motivating the development of an autonomous solution. We built a fully autonomous system around the TCAM (TermiBrain Causal Action Model) framework, with the design principle that hardware, perception, data, and learning should jointly reduce the physical interaction complexity the policy must handle. A custom 3D-printed gripper designed for single-layer fabric separation improves picking reliability on a dual-arm ARX X5 platform. A wrist-centric four-camera setup pairs upper fisheye cameras for task-level context with lower RGB cameras for close-range gripper-cloth contact observation. We combine portable UMI-style demonstrations with real-robot demonstrations collected on the deployable platform to provide both broad manipulation priors and deployment-specific dynamics. TCAM ties these components into a closed loop: each trajectory is analyzed to identify the physical factors contributing to its outcome, driving targeted data recollection and policy fine-tuning. The policy outputs 30-step end-effector delta-pose action chunks from a multi-view VLA backbone. In the final competition, our system loaded 25 T-shirts at an average of approximately 23 seconds per attempt, with 22 achieving the required surface smoothness, securing first place in Track 4.

0.04

IORA: Irregular Object Immobilization under Restricted Actuation

cs.RO ·2026-10-22 ·Sang-Hun Han, Changyeon Won, JunGyu Lee, Min-Gyu Park, Hae-Gon Jeon
similarity 0.67
Abstract · Preprint

Stable grasping under task-specific disturbances is important for robotic manipulation. However, most dexterous grasp synthesis methods are developed for highly actuated hands in free space, and low-DoF hands may not be able to realize the contact topologies required by these grasps. Meanwhile, support surfaces can provide useful contact forces, but are often treated only as geometric constraints. We present a support-aware grasp synthesis framework for object immobilization with low-DoF coupled hands. Given irregular object geometry, our method represents both hand and object local surface regions as graphs and searches for kinematically feasible matchings between them. We then refine the wrist pose and motor state for geometric contact feasibility and validates the refined grasps through physical rollouts. Starting from the validated grasp pose, an optional task-guided local search explores nearby grasp configurations by varying the wrist pose and motor state, and selects one according to the specified task condition. Experiments on diverse objects show that our method generates various grasp configurations that achieve high grasp success and strong disturbance resistance. Real-world experiments further demonstrate physically executable grasps which enable object immobilization in cooking scenario.

0.09

Control Architecture for Safe Grasping of Fragile Objects Using a Coarse Position-Controlled Gripper

cs.RO ·2026-09-11 ·Marko Pavlic, Moritz Geier, Timo Markert, Darius Burschka
published similarity 0.66
Abstract · Accepted for IEEE IROS 2026 publication

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

0.28

GOTT: Object-centric Dexterous Manipulation with a Reusable Cross-Embodiment Primitive

cs.RO cs.AIcs.CV ·2026-10-02 ·Yulin Liu, Lai Wei, Yen-Jen Wang, Akash Sharma, Pieter Abbeel +2 more
code/data similarity 0.66
Abstract · Project page: https://dex-gott.github.io/

Foundation models and large-scale human data provide rich sources of manipulation intent, but translating this intent into multi-fingered robot behavior remains difficult. Dexterous hands still lack a reusable low-level primitive that reliably establishes contact across tasks and embodiments. We propose GOTT, a reach-acquire-move framework built around a single cross-embodiment contact-acquisition primitive. Given a robot-agnostic object trajectory and a reach specification, GOTT first brings the hand near a task-relevant contact region. The shared closed-loop primitive then establishes stable contact from this approximate initialization, and a pose-conditioned controller tracks the desired object motion. Reach specifications may come from future-aware planning, external models, or human demonstrations, while the primitive and tracking backend remain unchanged. Simulation and real-world experiments show that GOTT is able to establish robust contact across diverse objects, arm-hand platforms, and seen and unseen hand morphologies. It also consistently improves end-to-end task success over open-loop grasp execution.

0.45

SimTO-Robust: Automated Design of Soft Grippers Robust to Grasp Pose and Object Geometry

cs.RO ·2026-10-29 ·Kurt Enkera, Joshua Pinskier, Marcus Gallagher, David Howard
similarity 0.66
Abstract

Robotic grippers operating in unstructured environments must robustly grasp objects of different shapes and sizes despite perception and positioning errors. Soft grippers that can achieve this robustness through intelligent mechanical design rather than sophisticated control software offer a promising solution. However, no existing computational design framework explicitly optimises soft gripper morphology for robustness across object geometries and grasp poses. We introduce SimTO-Robust, a generalisation of simulation-driven topology optimisation (SimTO) that simulates grasps across multiple objects and poses and aggregates their contact forces to guide gripper morphology optimisation. We generate 6,646 designs and physically evaluate 24 of them alongside 10 specialised SimTO designs, two rigid baseline grippers, and a baseline generalist soft gripper produced using conventional topology optimisation. All 37 grippers are tested in a pick-and-place task involving five feature-rich objects and six grasp poses, with external disturbances of increasing magnitude applied during the task. On average, SimTO-Robust designs complete pick-and-place more reliably than specialised SimTO designs and the rigid baselines. The best SimTO-Robust designs also withstood more of the applied disturbances than any other tested gripper. These results show that incorporating diverse grasp conditions into simulation-driven topology optimisation is a simple and effective approach to improving real-world soft gripper robustness. More broadly, they show that robust robotic grasping can be achieved through intelligent mechanical design rather than sophisticated sensing and control.

0.24