CS Paper Radar

Design optimization of tendon-driven robots considering tendon wrapping and shortcut

Yuta Sahara, Kento Kawaharazuka, Kei Okada

cs.RO ·submitted 2026-10-07 08:21 UTC · v1
published

Abstract

This study proposes a multi-objective optimization method for tendon-driven arm design, addressing the inherent trade-off between joint torque and arm thickness through tendon wrapping and shortcut effects. We formulate the problem to simultaneously maximize torque and minimize thickness, solved using NSGA-II. The algorithm optimizes tendon routing, pulley configurations, and attachment points. Results reveal Pareto-optimal designs with effective moment arm expansion via strategic shortcuts, providing practical guidelines for compact high-torque arms. The optimized configurations demonstrate non-trivial patterns beyond conventional design intuition, offering new insights for engineering efficient robotic systems.

Comment
Accepted to Advanced Robotics, website: https://haraduka.github.io/opt-wrap-shortcut
DOI
10.1080/01691864.2026.2723650

Closest papers

Nearest neighbours by meaning across the whole index.

PACT: Pose-Robust Actuation Co-Design for Tendon-Driven Robotic Hands

cs.RO ·2026-11-03 ·Prashant Kumar, Rachael Granberry, Taylor Niehues, Andrew A. Stanley, Gabe Pirie
similarity 0.62
Abstract

Humanoid robotic hands must provide sufficient force, speed, and backdrivability within a human-scale envelope. Tendon-driven transmissions address this challenge by relocating actuators to the palm and forearm, but routing paths, moment arms, and capstan dimensions jointly determine both force capability and joint speed, so selecting them sequentially satisfies one requirement at the expense of the other. This paper presents a pose-robust actuation co-design for tendon-driven robot hands (PACT) framework that optimizes tendon routing, moment arms, and capstan dimensions under pose-dependent force requirements and drivetrain-bandwidth constraints. A feasible-force formulation enforces actuator bounds and equilibrium at all joints, while a max-min objective maximizes task-force coverage at the weakest pose. Applied to a four-degree-of-freedom finger, the framework produces an asymmetric N + 1 tendon topology using quasi-direct-drive actuators. Across eight poses, the design achieves task-force coverage of 0.88-1.00 and a predicted 5 Hz minimum isolated-joint flexion/extension bandwidth within a 70th-percentile human-size envelope. Prototype measurements deviate from predictions by up to 24.5%, primarily due to unmodeled transmission losses. These results indicate that co-designing routing with the drivetrain can meet pose-dependent force requirements without relaxing the bandwidth constraint, paving the way for human-sized robotic hands with human-level performance.

0.08

MuJoCable: Reduced-Order Surface-Routed Cable Transmission for Tendon-Driven Robots

cs.RO cs.CE ·2026-09-09 ·Yi Zhang, Qi Shao, Yicong Lin, Muyuan Ma, Tao Sun +1 more
similarity 0.56
Abstract · 14 pages, 6 figures, 3 tables

Tendon transmissions reduce distal inertia and add compliance, yet routing, slack, and friction govern motion and force transfer. Mainstream rigid-body robotics simulators such as MuJoCo do not jointly resolve moving noncircular contact, unilateral tension, and segment friction. We present MuJoCable, which adds a reduced-order, configuration-dependent cable transmission to MuJoCo. Its routing algorithm jointly optimizes an ordered path across moving analytic and mesh surfaces. A unilateral axial law, directional Capstan propagation, and nodal virtual work map this path to segment tensions and body forces. The warm-started engine plugin applies these forces during simulation and exposes route and load states for design. Pulley benchmarks recover analytical transmission relations with a Capstan-ratio error below 0.5%. On the underactuated 18-joint SpiRobs, MuJoCable reveals friction-driven load growth and proximal redistribution of joint rotation that the native tendon does not represent. Hardware tests on SpiRobs and a tendon-route-coupled finger reproduce observed motion sequences. By making physical threading executable, MuJoCable brings transmission sources of the simulation-to-reality gap into route, cable, and actuator design before fabrication.

0.26

Actuation and Control of Passive Tendon-Driven Soft Extensions Through Rigid Manipulator Motion

cs.RO ·2026-11-11 ·Ignacio Cuiral-Zueco, Gonzalo López-Nicolás, Youcef Mezouar
theorycode/data similarity 0.56
Abstract · 16 pages, 12 figures. Soon to be submitted to the IEEE Transactions on Robotics. Code: https://github.com/nachocz/passive_soft_extension_con…

Industrial manipulators offer reach and precision but can damage nearby structures in confined spaces. Soft robots provide compliant contact but typically have limited reach. Rigid-soft systems combine their advantages, although they often require dedicated actuation and control hardware. We propose actuating a passive tendon-driven soft extension through manipulator joint motion. As the robot moves, the exterior spans of tendons anchored to upstream links change, altering tendon tension and deforming the extension. Inspection through narrow apertures, for example, constrains the motion of the end effector (EE). We develop a controller that regulates the soft tip while preserving such EE constraints. A differential model separates rigid transport from soft deformation, combining analytic arm and tendon kinematics with a locally identified span-to-deformation map. We also derive a local upper bound on the number of independent deformation directions transmitted by the tendons under the EE constraint, and conditions for the exponential convergence of the tip error. A quadratic program with control barrier functions imposes obstacle clearance, fulcrum limits, and model-validity conditions. Simulations and real experiments show tip and shape regulation under free, position-constrained, and fulcrum-constrained EE motion.

0.54

Task-Oriented Co-Design and Optimization of Geared Actuators for Robotic Applications

cs.RO ·2026-09-19 ·Xuanyu Huang, Jianqiang Dong, Hang Zhao
hot direction similarity 0.56
Abstract

Different tasks performed by legged robots impose distinct torque and speed requirements on actuators. Existing robotic actuators are generally optimized at the component level for metrics such as torque or power density, without explicit task guidance. System-level optimization across components such as motors, gearboxes, and sensors is challenging because of the high computational cost and coupling among mechanical, electrical, and electromagnetic behaviors. Consequently, improvements in individual components may not translate into better robot performance in a specific task. To this end, we present a systematic optimization framework for task-oriented co-design of actuator hardware and control. First, surrogate models are employed to accelerate motor evaluation and support global exploration of the coupled design space. Then, a hierarchical mixed-variable optimization strategy is adopted, combining discrete enumeration with continuous search over dimensions and real-valued indices. These indices are rounded to select admissible values for the remaining discrete choices before each evaluation. Within this search, rated output torque density and task performance are jointly optimized, with Bezier-parameterized joint torque profiles determined for each hardware candidate. Finally, the effectiveness of the proposed framework is validated through actuator fabrication and experiments on a two-degree-of-freedom jumping leg. Based on its measured mass, the fabricated prototype achieves a nominal rated output torque density of 35.7 N m/kg, approximately 60% higher than that of a widely used commercial geared joint actuator, while being 18.6% lighter. Under matched bench conditions, it achieves 12.0% greater jump height at twice-rated torque. Together, these results demonstrate a systematic route from task requirements to actuator design and control.

0.36

PHD-Hand: A Printable Humanoid Dexterous Hand with Linkage-Driven 3-DOA Digits

cs.RO cs.AI ·2026-10-21 ·Neel Adwani, Muhaiminul Islam Akash, Saffia Ouali, Ethan Liu, Cong Wang
published similarity 0.56
Abstract · Submitted and Accepted at IEEE-RAS International Conference on Humanoid Robots (Humanoids 2026). 8 pages. Supplementary video: https://lnkd.…

Currently, dexterous humanoid robot hands are widely considered the final hardware bottleneck that hampers generalist robots from physically assisting people at home and work. As conventional tendon-driven designs suffer from high cost, demanding maintenance, poor reliability, and short durability, alternative linkage-driven designs have increasingly gained attention. Despite their potential to avoid the weaknesses of tendon-driven hands, integrating multiple degrees of actuation (DOA) in a single digit with linkage drivetrains is a challenge for design and fabrication. Only a few studies have managed to present functional humanoid hands that are completely linkage-driven and have at least three DOAs per digit without compromising actuator placement and other design preferences. Our work introduces a new linkage-driven hand featuring a unique flexure hinge. Together with elastic drive rods made of spring steel, the linkage drivetrains are significantly simplified. Unlike other linkage-driven designs of similar dexterity, our design does not require many miniature moving parts. As a result, the hand can be fabricated easily with a budget 3D printer. This not only significantly lowers the barrier to entry for using and developing dexterous humanoid robot hand functions, but also allows the hands to be sized much closer to regular human hands. The design offers desirable kinematic advantages as well. A prototype is evaluated for grasping and object manipulation. In addition, this paper presents our latest findings on kinematics and control of the hand.

0.25

Design Optimization for Large High-Force Soft Robot Manipulators Under Gravitational Loads

cs.RO ·2026-08-17 ·Isara Cholaseuk, Penelope Llibre, Alexa Kyriacou, Audrey Wang, Akua K. Dickson +3 more
top venue similarity 0.55
Abstract · 8 pages, 8 figures

Designing large soft robots capable of generating high forces for physical human-robot interaction remains a significant challenge in soft robotics. Prior work in large soft robots has focused on proof-of-concept prototypes, and no systematic framework exists for determining the suitability of a design paradigm for a desired task. This manuscript introduces a method for optimizing the geometry of a soft robot limb, maximizing its blocking force subject to an anti-bucking constraint under its own gravitational loading. We demonstrate that an explicit solution exists to the proposed optimization problem under certain assumptions. Experiments with three geometries of a large, soft, pneumatically-actuated manipulator demonstrate that the method correctly predicts which designs meet constraints and which produces the largest end-effector forces. This method, with its closed-form solution, can allow designers to determine a-priori if an intended class of soft manipulators is an appropriate choice for physical interaction at large size scales.

0.54

Design and Validation of an Antagonistic Tendon-Driven Dexterous Robotic Hand with Bidirectional Operation

cs.RO ·2026-09-28 ·Chunghyeon Lee, Hyukjun Kwon, Sungeon Kim, Saehyun Moon, Seokhwan Jeong
similarity 0.55
Abstract

Dexterous robotic hands typically reproduce human hand morphology but inherit its one-sided grasping workspace, requiring wrist or arm reorientation to grasp from the opposite side. Existing reversible hands generally rely on non-anthropomorphic, soft, or task-specific finger arrangements, whereas conventional five-digit anthropomorphic hands remain designed primarily for palmar-side grasping. This paper presents an anthropomorphic, human-scale (200 mm length), lightweight (220 g), 3D-printed, 17-DoF robotic hand built on a bidirectional antagonistic tendon-routing mechanism, in which flexion/extension (except the coupled joint) and abduction/adduction at joints are actively driven without passive return springs. The proposed routing mechanism allows all degrees of freedom to cross their neutral configuration and form grasp closures on either the palmar or dorsal side. Experimental evaluation demonstrates an average motor-to-joint transmission error of 3.0%, an average joint transmission bandwidth of 13.2 Hz, a maximum fingertip force of 29 N, and a positioning repeatability up to 0.15 mm. The hand further achieves a Kapandji score of 8, successfully performs all 33 GRASP Taxonomy grasp types, and performs palmar- and dorsal-side grasping tasks, validating bidirectional operation in a compact, human-scale platform.

0.35

Optimization Design and Simulation Validation of a Variable Stiffness Actuator Based on a Crossed Four-Bar Mechanism

eess.SY ·2026-09-16 ·Yuanlong Ji, Ruizhe Jiang, Xiangyu Xie, Junheng Lin, Dongrun Jin +1 more
published similarity 0.54
Abstract · 7 pages, 5 figures

This paper presents a bio-inspired antagonistic variable stiffness actuator (VSA) based on two crossed four-bar compliant transmission elastic units (CFB-CTEs). The design addresses the difficulty of combining nonlinear elastic shaping with low structural inertia in antagonistic VSA mechanisms. Inspired by the crossed constraint behavior of the anterior and posterior cruciate ligaments during knee flexion, the proposed actuator uses geometric transmission, elastic energy storage, and bilateral antagonistic arrangement to shape the output torque and equivalent stiffness. A multi-objective optimization model is established to balance torque tracking accuracy, equivalent inertia, and mass. The selected compromise design achieved a torque root-mean-square error (RMSE) of $0.883~\mathrm{N\,mm}$ and a total mass of $50.2~\mathrm{g}$. Its average equivalent inertia was reduced by about 78% compared with an independent torque-only optimized design. An ADAMS multibody model was further built to verify the structural response under single-input, opposite-input, and same-input conditions. The results support the feasibility of the proposed crossed four-bar elastic unit as a lightweight nonlinear elastic branch for antagonistic VSAs.

0.68