CS Paper Radar

MuJoCable: Reduced-Order Surface-Routed Cable Transmission for Tendon-Driven Robots

Yi Zhang, Qi Shao, Yicong Lin, Muyuan Ma, Tao Sun, Yue Xie

cs.RO cs.CE ·submitted 2026-09-09 02:11 UTC · v2

Abstract

Tendon transmissions reduce distal inertia and add compliance, yet routing, slack, and friction govern motion and force transfer. Mainstream rigid-body robotics simulators such as MuJoCo do not jointly resolve moving noncircular contact, unilateral tension, and segment friction. We present MuJoCable, which adds a reduced-order, configuration-dependent cable transmission to MuJoCo. Its routing algorithm jointly optimizes an ordered path across moving analytic and mesh surfaces. A unilateral axial law, directional Capstan propagation, and nodal virtual work map this path to segment tensions and body forces. The warm-started engine plugin applies these forces during simulation and exposes route and load states for design. Pulley benchmarks recover analytical transmission relations with a Capstan-ratio error below 0.5%. On the underactuated 18-joint SpiRobs, MuJoCable reveals friction-driven load growth and proximal redistribution of joint rotation that the native tendon does not represent. Hardware tests on SpiRobs and a tendon-route-coupled finger reproduce observed motion sequences. By making physical threading executable, MuJoCable brings transmission sources of the simulation-to-reality gap into route, cable, and actuator design before fabrication.

Comment
14 pages, 6 figures, 3 tables

Closest papers

Nearest neighbours by meaning across the whole index.

SHAFT: A Slack-Compensating, Helical-Buckling-Attenuating Flexible-Shaft Transmission for Lightweight Multi-DoF Manipulation

cs.RO ·2026-09-19 ·Tomoya Takahashi, Moses Gladson Selvamuthu, Richiro Tadakuma, Kazutoshi Tanaka
published similarity 0.62
Abstract · 9 pages, 14 figures, submitted as proceedings of IROS2026

Lightweight and slim manipulators enable safe operation in human living environments. Proximal actuation using remote transmission mechanisms, such as wire-driven or Bowden cables, effectively reduces inertia and arm size by relocating motors near the base and transmitting torque to distal joints. Existing approaches either increase mass through additional components, such as pulleys for direction changes, or suffer from reduced transmission efficiency due to friction losses. Flexible shaft transmission avoids both mass increase and excessive friction losses, but faces increasing angular transmission error due to helical buckling caused by slack generated at joint bending. To address this problem, we propose SHAFT: a Slack-compensating, Helical-buckling-Attenuating Flexible- shaft Transmission mechanism. This mechanism compensates for slack through a proximal tensioner, improving the angular transmission error and efficiency of flexible shaft transmission without increasing the moving mass of the arm section. In a transmission path containing four 90-degree bends, the proposed mechanism demonstrated approximately 30% higher efficiency and approximately 65% lower angular transmission error compared to a flexible shaft transmission without a tensioner. Using this mechanism, we fabricated a 6-Degree-of-Freedom (DoF) arm with a 1-DoF gripper manipulator consisting of a rotary module housing motors with a tensioner, and a 280 g weight for the arm module. The proposed manipulator represents a novel remote actuation system for achieving lightweight construction with high efficiency, contributing to the acceleration of safe robot deployment in human environments.

0.42

An Open MuJoCo Simulation Framework for a Quadrotor Carrying a Tendon-Driven Soft Continuum Arm

cs.RO eess.SY ·2026-10-11 ·Haitham El-Hussieny
code/data similarity 0.61
Abstract

Combining aerial robots with soft continuum manipulators promises safe, compliant interaction with the environment, but the coupled dynamics of a free-flying base and a highly deformable, underactuated arm are difficult to study without a suitable simulator. This paper describes an open-source simulation framework, built on the MuJoCo physics engine, for a quadrotor that carries a tendon-driven soft continuum arm underneath its body. The arm is modelled as a pseudo-rigid-body chain of twelve segments joined by pairs of orthogonal compliant hinges. Three tendons, spaced \SI{120}{\degree} apart and routed through every segment, bend it in any direction. A geometric tracking controller on $SE(3)$ flies the vehicle; its rotor allocation matrix is generated directly from the model description. A closed-form tendon-tension allocation keeps every tension within its limits and gives the same bending moment in every direction. We report the full set of modelling choices and parameters, and we evaluate the framework in four simulated scenarios: a \SI{36}{\second} mission with a figure-eight and a tendon-driven tip sweep, an attitude-gain study, a quasi-static characterization of the bending workspace, and an impulsive disturbance applied to the arm tip. With the nominal gains the vehicle tracks the mission with \SI{3.1}{\centi\meter} RMS position error while the arm tip swings up to \SI{37}{\centi\meter} from the body axis. The gain study shows that a low-bandwidth attitude loop lets the arm excite sustained oscillations. The simulation runs about $15\times$ faster than real time on a laptop CPU. All models, controllers and scripts that reproduce the figures are released.

0.25

Design of a Fully Actuated 4-DOF Robotic Finger With Joint-Specific Hybrid Remote Actuation

cs.RO ·2026-10-07 ·Hyojae Kang, Hyun-mok Jung, Joonho Lee, Dongil Park, Hyunmin Do +2 more
similarity 0.60
Abstract · 10 pages, 10 figures. This manuscript has been submitted for possible publication

This paper presents a fully actuated 4-DOF robotic finger using a joint-specific hybrid remote-actuation architecture. The metacarpophalangeal (MCP) joint is driven by two coordinated rigid-link transmission sets, whereas the proximal interphalangeal (PIP) and distal interphalangeal (DIP) joints are independently actuated by closed-loop wire transmissions incorporating circular rolling-contact joints (RCJs). A larger transmission radius is used at the PIP joint than at the DIP joint. The RCJ wire geometry maintains the total wire-loop length during joint rotation, and the DIP wire routing is designed so that PIP motion does not affect its differential actuation for a fixed MCP configuration. The distal wire transmission, MCP linkage, and fingertip kinematics are analytically modeled. In experiments, the transmission behavior was quantitatively evaluated from the ball-screw displacements measured using ArUco-marker tracking. MCP actuation produced measurable displacements of the PIP and DIP transmission units, whereas isolated PIP and DIP actuation with the MCP fixed supported the intended mechanical decoupling between the distal transmissions. The mean peak fingertip forces under isolated MCP, PIP, and DIP actuation were 21.28 N, 9.22 N, and 5.75 N, respectively. The resulting finger postures were also examined using objects of different geometries and sizes.

0.37

PACT: Pose-Robust Actuation Co-Design for Tendon-Driven Robotic Hands

cs.RO ·2026-11-03 ·Prashant Kumar, Rachael Granberry, Taylor Niehues, Andrew A. Stanley, Gabe Pirie
similarity 0.59
Abstract

Humanoid robotic hands must provide sufficient force, speed, and backdrivability within a human-scale envelope. Tendon-driven transmissions address this challenge by relocating actuators to the palm and forearm, but routing paths, moment arms, and capstan dimensions jointly determine both force capability and joint speed, so selecting them sequentially satisfies one requirement at the expense of the other. This paper presents a pose-robust actuation co-design for tendon-driven robot hands (PACT) framework that optimizes tendon routing, moment arms, and capstan dimensions under pose-dependent force requirements and drivetrain-bandwidth constraints. A feasible-force formulation enforces actuator bounds and equilibrium at all joints, while a max-min objective maximizes task-force coverage at the weakest pose. Applied to a four-degree-of-freedom finger, the framework produces an asymmetric N + 1 tendon topology using quasi-direct-drive actuators. Across eight poses, the design achieves task-force coverage of 0.88-1.00 and a predicted 5 Hz minimum isolated-joint flexion/extension bandwidth within a 70th-percentile human-size envelope. Prototype measurements deviate from predictions by up to 24.5%, primarily due to unmodeled transmission losses. These results indicate that co-designing routing with the drivetrain can meet pose-dependent force requirements without relaxing the bandwidth constraint, paving the way for human-sized robotic hands with human-level performance.

0.08

Design of a hybrid tendon-linkage finger with coupled and adaptive motion

cs.RO ·2026-11-09 ·Hyojae Kang, Giup Seo, Jae-Young Lee, Yeong Jae Park, Jongwoo Park +4 more
similarity 0.59
Abstract · This manuscript has been submitted for possible publication

Dexterous robotic fingers require coordinated joint motion and adaptability to object contact, while independently actuating multiple joints increases the complexity of the transmission mechanism. This paper presents a hybrid tendon--linkage robotic finger with four mechanical degrees of freedom driven by three actuators. The MCP abduction/adduction joint is driven through a bevel gear, while MCP and PIP flexion/extension are driven by separate bidirectional tendon transmissions. The DIP joint is not independently actuated but is coupled to the PIP joint through a four-bar linkage with a torsional spring and mechanical stopper. The tendon routing also introduces mechanical coupling between the MCP and PIP joints. Kinematic analysis was conducted to describe the coupled and adaptive motions, and experiments were performed to evaluate the joint motion characteristics. ArUco-based measurements showed that the coupled motion closely matched the theoretical prediction, whereas the adaptive motion was partially limited by interference between linkage components. The fabricated finger demonstrated different contact postures with cylindrical, cuboid, and irregularly shaped objects, and the mean peak fingertip force was 4.56 N. The proposed mechanism provides both coupled motion and contact-dependent adaptation without requiring an additional actuator for the DIP joint.

0.13

MUSBRIC: LEGO-Compatible Pneumatic Muscle Bricks for Reconfigurable Musculoskeletal Robots

cs.RO ·2026-10-29 ·Qiyao Wang, Yinglei Zhu, Liang Zhou, Wenzhe Gong, Xin-Jun Liu +1 more
similarity 0.58
Abstract · 6 figures. Qiyao Wang and Yinglei Zhu contributed equally to this work. Improved HTML rendering of Figure 1; scientific content unchanged

Musculoskeletal robots combine compliant actuators with articulated skeletons, but exploring alternative configurations often requires repeated fabrication. We present MUSBRIC, a modular hardware platform and accompanying MuJoCo-based simulator for reconfigurable musculoskeletal robots. LEGO-compatible endcaps turn fiber-reinforced extensile pneumatic artificial muscles into reusable, plug-and-play muscle bricks that connect directly to standard LEGO components. Experimentally identified actuator behavior supports corresponding musculoskeletal simulations. An elbow-joint prototype validates load-dependent flexion and extension, showing that pulley-guided routing enables reversible motion and a mechanical stop stabilizes the straight posture. A robotic hand demonstrates compliant grasping and multi-joint construction. Matched hardware and simulation sweeps across 15 leg configurations demonstrate systematic exploration of attachment geometry, while a quadruped assembled from four legs demonstrates walking. Together, these demonstrations span mechanism analysis, configuration exploration, and functional robot construction within a single reconfigurable system. The hardware designs and simulation code will be released as open source soon to facilitate reproduction and further development.

0.35

Aero Hand Open: A Simulation-Ready Tendon-Driven Hand for Dexterous Manipulation Learning

cs.RO cs.AIcs.LG ·2026-08-28 ·Nan Wang, Mohit Yadav, Jonathan Wulff, Aidan Rosenbaum, Kezhou Chen +3 more
code/data similarity 0.58
Abstract · 20 pages, 9 figures. Project page: https://chestnut-robotics.github.io/aero-hand-open/

Tendon-driven hands are anthropomorphic, and moving the actuators off the joints is what makes a hand of this capability affordable to build. Two effects produce that saving. Routing force through a cable removes the requirement that a motor fit inside the joint it drives, so smaller and cheaper motors suffice, and one motor can drive several joints through a single cable, so fewer motors are needed. They are also harder to learn on than a direct-drive hand. The underactuated transmission that produces the saving is itself difficult to represent in a simulator, and the joints one cable drives are not independently commandable. We present Aero Hand Open, a tendon-driven anthropomorphic hand that is released simulation-ready. Three things ship with it. A simulation model reproduces the cable transmission itself. An identified actuation map connects that model to the motor commands in both directions, including the three-way coupling of the thumb. A reinforcement learning package trains policies for the hand. Together they let a policy be trained entirely in simulation and run on the hand with no fine-tuning and no state estimation. We release the mechanical design, the simulation model, the identified mapping, the training environment and the deployment stack.

0.47

Passive Stiffness Shaping in Cable-Suspended Aerial Manipulation via Movable Compliant Anchors

cs.RO cs.MAeess.SY ·2026-09-30 ·Antonio Franchi, Amr Afifi
similarity 0.56
Abstract

Cable-suspended aerial manipulation offers a lightweight architecture for cooperative transportation and physical interaction, yet the passive mechanical response perceived at the load remains insufficiently understood and systematically exploited. This work interprets aerial vehicles as movable compliant anchors and develops a gravity-aware quasi-static theory for predicting and shaping the passive Cartesian stiffness of a suspended load. The formulation applies to an arbitrary number of aerial vehicles connected to a point load by taut, straight, inextensible cables. At a selected gravity-loaded equilibrium, aerial-anchor compliance and transverse cable geometric compliance combine in series within each leg, while the leg stiffnesses act in parallel on the load. For isotropic aerial-anchor behavior, each leg is exactly equivalent to a virtual unilateral elastic cable, revealing an axial--transverse stiffness decomposition governed by the equilibrium tension. These results define a nonlinear map from commanded-anchor configuration to passive load stiffness, whose differential enables local constraint-preserving shaping through anchor repositioning. A dynamic rigid-body validation framework with nonlinear vehicle control, elastic-damped tendons, and environmental contact is defined to assess when and to what extent the derived stiffness remains predictive beyond the assumptions of the analytical model.

0.14