CS Paper Radar

MUSBRIC: LEGO-Compatible Pneumatic Muscle Bricks for Reconfigurable Musculoskeletal Robots

Qiyao Wang, Yinglei Zhu, Liang Zhou, Wenzhe Gong, Xin-Jun Liu, Huichan Zhao

cs.RO ·submitted 2026-10-29 15:36 UTC · v2

Abstract

Musculoskeletal robots combine compliant actuators with articulated skeletons, but exploring alternative configurations often requires repeated fabrication. We present MUSBRIC, a modular hardware platform and accompanying MuJoCo-based simulator for reconfigurable musculoskeletal robots. LEGO-compatible endcaps turn fiber-reinforced extensile pneumatic artificial muscles into reusable, plug-and-play muscle bricks that connect directly to standard LEGO components. Experimentally identified actuator behavior supports corresponding musculoskeletal simulations. An elbow-joint prototype validates load-dependent flexion and extension, showing that pulley-guided routing enables reversible motion and a mechanical stop stabilizes the straight posture. A robotic hand demonstrates compliant grasping and multi-joint construction. Matched hardware and simulation sweeps across 15 leg configurations demonstrate systematic exploration of attachment geometry, while a quadruped assembled from four legs demonstrates walking. Together, these demonstrations span mechanism analysis, configuration exploration, and functional robot construction within a single reconfigurable system. The hardware designs and simulation code will be released as open source soon to facilitate reproduction and further development.

Comment
6 figures. Qiyao Wang and Yinglei Zhu contributed equally to this work. Improved HTML rendering of Figure 1; scientific content unchanged

Closest papers

Nearest neighbours by meaning across the whole index.

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.65
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14

An Open MuJoCo Simulation Framework for a Quadrotor Carrying a Tendon-Driven Soft Continuum Arm

cs.RO eess.SY ·2026-10-11 ·Haitham El-Hussieny
code/data similarity 0.62
Abstract

Combining aerial robots with soft continuum manipulators promises safe, compliant interaction with the environment, but the coupled dynamics of a free-flying base and a highly deformable, underactuated arm are difficult to study without a suitable simulator. This paper describes an open-source simulation framework, built on the MuJoCo physics engine, for a quadrotor that carries a tendon-driven soft continuum arm underneath its body. The arm is modelled as a pseudo-rigid-body chain of twelve segments joined by pairs of orthogonal compliant hinges. Three tendons, spaced \SI{120}{\degree} apart and routed through every segment, bend it in any direction. A geometric tracking controller on $SE(3)$ flies the vehicle; its rotor allocation matrix is generated directly from the model description. A closed-form tendon-tension allocation keeps every tension within its limits and gives the same bending moment in every direction. We report the full set of modelling choices and parameters, and we evaluate the framework in four simulated scenarios: a \SI{36}{\second} mission with a figure-eight and a tendon-driven tip sweep, an attitude-gain study, a quasi-static characterization of the bending workspace, and an impulsive disturbance applied to the arm tip. With the nominal gains the vehicle tracks the mission with \SI{3.1}{\centi\meter} RMS position error while the arm tip swings up to \SI{37}{\centi\meter} from the body axis. The gain study shows that a low-bandwidth attitude loop lets the arm excite sustained oscillations. The simulation runs about $15\times$ faster than real time on a laptop CPU. All models, controllers and scripts that reproduce the figures are released.

0.25

A Task-Agnostic Control Strategy for Dynamic Assistance with Pneumatically Actuated Soft Exosuits

cs.RO cs.HC ·2026-08-18 ·Anoush Sepehri, Zachary Huang, Raymond de Callafon, Michael T. Tolley, Tania K. Morimoto
similarity 0.60
Abstract

Pneumatic artificial muscles have provided new opportunities to develop upper-extremity soft exosuits for reha- bilitation, augmentation, and assisted daily living. However, the complex dynamics and limited bandwidth of these actuators has made providing responsive assistance based on user intention a longstanding challenge. In this work, we present an inverse-plant control strategy for pneumatically actuated soft exosuits that only relies on kinematic sensing for task-agnostic and dynamic assistance during daily living. We model the human-robot system using a Hammerstein dynamic model, consisting of a Preisach hysteresis model and a linear time-invariant filter, to capture the static and dynamic behavior of the system. We personalize our model to each user using 140 s of data and approximate an inverse to integrate into our control loop. When evaluated on a test rig that emulated a soft assistive exosuit for the wrist, our controller reduced the interaction torque by up to 73% and the activation of key flexor and extensor muscles by up to 47% relative to the condition with no assistance for speeds ranging from 8°/s to 120°/s. Overall, this work presents a control strategy that can provide task-agnostic, dynamic assistance with pneumatically actuated soft exosuits without the need for physiological or force sensors to interpret user intention.

0.19

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.60
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

QLAUN: A Research-Oriented, Robust, Agile, Modular, and Affordable Torque-Controlled Quadruped Robot

cs.RO ·2026-09-03 ·Mohamad S. Moudallal, Noel J. Maalouf
published similarity 0.60
Abstract · Extended abstract presented at IEEE ICRA@40, Rotterdam, Netherlands, September 2024. 2 pages, 1 figure

QLAUN Bot (Quad-Legged Adaptive Unmanned Navigator Robot) is a torque-controlled quadruped robot that is research-oriented, cost-effective, and aimed at achieving simultaneous robustness and agility while being completely 3D-printed. It is a quadruped robot that is aimed at empowering robotics research at universities and research institutes in Lebanon and the MENA region. Using a novel electronics-free leg design strategy, we present a modular robot with interchangeable and easily replaceable legs. The 15 kg robot possesses 12 DoF (Degrees-of-Freedom) with three per leg, each paired with a completely 3D-printed Quasi-Direct Drive (QDD) actuator that consists of a brushless DC motor and a low-ratio gearbox transmission that is connected to a belt transmission system for significantly increasing the torque outputs at the joints. We present legs that have decoupled hip and knee actuators to improve the overall modularity of the robot. QLAUN is almost completely 3D-printed using polylactic acid (PLA) and assembled using off-the-shelf parts to create a robust, agile, and affordable robot for legged robot locomotion research. The legs possess joints with wide ranges of motion, including a continuous hip flexion-extension joint. A compliant foot, printed using TPU-95A is also implemented for alleviating hard impacts and handling terrain uncertainties. This extended abstract aims to introduce QLAUN, a novel platform for robotics research, emphasizing the design concepts and principles that underpin its development to the academic and research communities in the field of robotics.

0.34

Tensegrity Continuum Robots Enable Task-Adaptive Morphologies for Cooperative Behaviors

cs.RO ·2026-08-27 ·Mahmud Hasan Saikot, Sydney Spiegel, Sudheera Akalanka Kariyawasam, Andrew Stefka, Josh Chrisler +1 more
top venue similarity 0.59
Abstract · 22 pages, 6 figures, Accepted to Nature Machine Intelligence

Robots that can change their morphologies and behaviors for different tasks and environments hold great promise for adaptable, multifunctional systems. Modular reconfigurable robots (MRRs) can achieve such functionalities by docking and rearranging individual units, but most rely on rigid modules that lack structural compliance, resulting in limited capabilities. Continuum robots offer compliance through flexible backbones, yet they cannot self-reconfigure into task-adaptive multi-robot configurations. Here, we introduce an MRR that unifies the advantages of both architectures by combining a tensegrity-based compliant body with claw-based connection mechanisms. Each robot can manipulate and locomote independently, and multiple robots can self-reconfigure into different morphologies (e.g., chains, loops, branches) for cooperative manipulation and locomotion. We demonstrate the robots' capability across diverse tasks and environments, including coordinated object manipulation and transport, multimodal locomotion, and loco-manipulation in real-world scenarios. These results lay a foundation for adaptable and multifunctional robotic collectives, with broad potential applications in manufacturing, space exploration, and search-and-rescue operations.

0.33

Detachable Wire Drive : Reconfigurable Robot Architecture with Shared Actuators

cs.RO ·2026-08-16 ·Takahiro Hattori, Kento Kawaharazuka, Kei Okada
published similarity 0.58
Abstract · Accepted at IROS2026, website - https://hatofly.github.io/detachable-wire-drive/

Reconfigurable robots offer significant potential for adapting to diverse tasks; however, conventional centralized architectures often require dedicated actuators for each module, leading to substantial increases in overall system weight, volume, and cost. To address these challenges, this paper presents the "Detachable Wire Drive," a reconfigurable robotic system that enables the sharing of heavy and expensive actuators across various morphologies. The core of this system is the "Wire Detach Unit," a mechanism designed to physically split and reconnect wire drive paths, allowing motors to be consolidated into a common base unit. We demonstrate the versatility of this approach by developing a 2-DOF rigid arm, a continuum arm, and two distinct grippers, all of which are interchangeably attached to, and driven by, a single shared actuator set. Experimental results validate the mechanical reliability of the detachment process and the control framework's ability to seamlessly manage transitions between configurations, highlighting a path toward more efficient and multi-functional robotic systems.

0.39

Flexible-body Modeling, Kinematic Identification, and Assembly Accuracy of Overconstrained Spatial Linkages

cs.RO math.AG ·2026-09-15 ·Daniel Huczala, Michael Pieber, Johannes Gerstmayr, Andreas Mair, Frederik Schulte +4 more
similarity 0.58
Abstract

Overconstrained rational single-loop linkages are efficient, compact, and low-cost custom mechanisms, yet their deployment in industrial settings is limited. In simulations, rigid body formulations fail due to redundant constraints. This study presents a flexible multibody modeling framework based on the floating frame of reference formulation, and delivers an overall accuracy analysis of assembled linkages prototypes. The approach is validated against 3D-printed PLA prototypes of a Bennett four-bar mechanism, including variants with intentional joint-axis misalignment, which theoretically, from the rigid body point of view, cannot be assembled. A supplementary contribution is delivered in the form of a kinematic parameter identification methodology suited for this type of mechanism with ill-conditioned Jacobian. The experimental and simulation results are compared and reveal that these overconstrained mechanisms exhibit a self-assembling tendency -- structural compliance drives the assembly toward the ideal geometric configuration, distributing constraint stress throughout the structure. Additional qualitative demonstrations using cardboard tubes and bamboo sticks as link building blocks confirm that functional mechanisms can be realized from low-cost, unconventional materials with limited manufacturing accuracy. The proposed modeling pipeline is fully algorithmic and enables design optimization in the future.

0.18