CS Paper Radar

Flexible-body Modeling, Kinematic Identification, and Assembly Accuracy of Overconstrained Spatial Linkages

Daniel Huczala, Michael Pieber, Johannes Gerstmayr, Andreas Mair, Frederik Schulte, Silvia Glas, Tomas Postulka, Ales Vysocky, Martin Pfurner

cs.RO math.AG ·submitted 2026-09-15 07:52 UTC · v1

Abstract

Overconstrained rational single-loop linkages are efficient, compact, and low-cost custom mechanisms, yet their deployment in industrial settings is limited. In simulations, rigid body formulations fail due to redundant constraints. This study presents a flexible multibody modeling framework based on the floating frame of reference formulation, and delivers an overall accuracy analysis of assembled linkages prototypes. The approach is validated against 3D-printed PLA prototypes of a Bennett four-bar mechanism, including variants with intentional joint-axis misalignment, which theoretically, from the rigid body point of view, cannot be assembled. A supplementary contribution is delivered in the form of a kinematic parameter identification methodology suited for this type of mechanism with ill-conditioned Jacobian. The experimental and simulation results are compared and reveal that these overconstrained mechanisms exhibit a self-assembling tendency -- structural compliance drives the assembly toward the ideal geometric configuration, distributing constraint stress throughout the structure. Additional qualitative demonstrations using cardboard tubes and bamboo sticks as link building blocks confirm that functional mechanisms can be realized from low-cost, unconventional materials with limited manufacturing accuracy. The proposed modeling pipeline is fully algorithmic and enables design optimization in the future.

Closest papers

Nearest neighbours by meaning across the whole index.

Lego-Like Stiffness Configuration of Planar Compliant Modules for Task-Specific Flexible Interfaces

cs.RO ·2026-10-05 ·Siyue Yao, Xiaochi Xie, Shixuan Zhao, Yutong Li, Hao Li +2 more
similarity 0.66
Abstract · 8 pages, 8 figures

Compliant mechanisms provide compact and intrinsic structural compliance for regulating physical interactions between mechanisms and environments. However, different tasks demand distinct stiffness characteristics, often requiring task-specific optimization and redesign due to limited geometric design space and inherent coupling among multiple stiffness components. This paper presents a Lego-like stiffness configuration approach using stackable planar compliant modules. Three complementary module geometries are introduced, with their stiffness characteristics further regulated through beam width, plate thickness, and module orientation. A unified stiffness model is established for quantitative analysis of individual and composed modules. Further, a two-stage optimization method is presented to achieve desired stiffness profiles, combining a genetic algorithm for configuration and sequential quadratic programming for parameter refinement. Experimental verification shows deviations below 6.5% for simulated stiffness. A flexible wrist is further developed as a representative implementation, exhibiting distinct compliant and dynamic responses under different stiffness characteristics. An optimized modular composition realizes prescribed stiffness values and maintains compliant obstacle interaction during high-speed motion at 1 m/s, with a maximum tested angular compliance of approximately $15^\circ$. The proposed framework provides a systematic approach for constructing flexible interfaces with task-specific stiffness characteristics.

0.23

SNAP3D: Physically Grounded 3D Parts for Assembly from a Single Image

cs.GR cs.CV ·2026-09-11 ·Yu-Rou Tuan, Hao-Tang Tsui, Nicolas Ugrinovic, Kris Kitani, Xiaoxuan Ma
code/data similarity 0.61
Abstract · Project page: https://lucytuan.github.io/SNAP3D/

Part-aware 3D asset generation enables applications such as editing, articulation, simulation, and fabrication, yet existing methods can generate visually complete individual parts without ensuring that they form a valid physical assembly. Consequently, generated neighboring parts may interpenetrate, lack valid connections, or collapse under gravity. We propose a physics-guided framework for improving single-image part-aware 3D generation with physically compatible geometry and stable connections. Our method resolves inter-part penetration, recovers a contact graph between neighboring parts, and introduces parameterized connectors at their contact surfaces. Using feedback from physical simulation, we refine connector placement, orientation, and dimensions to improve assembly stability while preserving the generated geometry. We further introduce a physics-based evaluation protocol that complements conventional geometric metrics by directly testing assembly validity and stability under gravity. Experiments comparing against multiple part-aware 3D generators show substantial improvements in physical realizability and stability while maintaining geometric quality. We additionally validate the resulting parts through 3D printing and real-world assembly.

0.38

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.61
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Compositional Aeroelastic Operators for Morphing Flexible Multibody Aircraft: A Geometric Framework with Structural Verification

cs.CE math.NAphysics.flu-dyn ·2026-08-15 ·Gelin Chen, Chen Song, Chao Yang
similarity 0.60
Abstract · 30 pages, 2 figures, 2 tables

Morphing flexible multibody aircraft require structural strain, aerodynamic geometry, surface velocity, and generalized loading to remain compatible as joints and flexible components change configuration. A compositional formulation is developed around an assumed material attachment between each lifting surface and a geometrically exact beam. Separating the component root pose from the section field shows that the body strain and elastic potential of a component depend on its own elastic coordinates, while upstream motion enters kinetic terms and external-load pullbacks. At element level, an exact relative logarithm $d$ supplies strain and potential energy, whereas a reference-anchored section coordinate $σ$ supplies deformed section geometry. Finite-order expansions retain the finite reference geometry exactly and truncate only endpoint perturbations. The attachment map then generates surface points, tangents, normals, velocities, and force Jacobians from common section kinematics. Euler--Poincare beam balance, moving-surface potential-flow relations, graph cotangent assembly, and the associated semidiscrete power identity are stated in a common twist--wrench convention. Collocation, pressure, equivalent-load, and structural-station sites are distinguished to expose their approximation errors. Verification gives the expected $N_d+1$ convergence order for degree-$N_d$ relative-log expansions. In a geometrically nonlinear cantilever comparison, a cubic static-manifold correction reduces mean full-record displacement error from $0.479$ to $0.255$ over four completed load cases. These results provide structural and interface-level evidence rather than validation of a complete aircraft aeroelastic prediction.

0.10

Manipulation with Stability Guarantees: Linear Deformable Objects with Non-negligible Physical Response Grasped at Multiple Location

cs.RO ·2026-09-22 ·Daniel Feliu-Talegon, Cosimo Della Santina
similarity 0.60
Abstract · 19 pages, 13 figures

Most research on the manipulation of deformable objects focuses on lightweight systems with negligible mechanical response, effectively restricting attention to quasi-static regimes. This assumption excludes a broad class of practically relevant objects, such as hoses, pipes, and wiring harnesses, whose dynamics cannot be ignored during manipulation. In this work, we address this limitation by introducing a closed-loop control architecture that explicitly accounts for object dynamics and recasts manipulation as a shape-regulation problem. Control is achieved by modulating forces and torques applied at multiple fixed points along the object. This approach builds on three methodological contributions: a fully dynamic model of linear deformable objects based on discrete strain parameterizations; an extension of the notion of actuation coordinates to SE(3), yielding a structured and inherently underactuated control architecture; and nonlinear feedback strategies providing explicit conditions for steady-state convergence to desired configurations. Extensive simulations on representative manipulation tasks demonstrate the performance gains enabled by the proposed modelbased formulation. We finally validate the approach experimentally through a real-time closed-loop implementation with online shape estimation, confirming its practical feasibility and effectiveness

0.33

MUSBRIC: LEGO-Compatible Pneumatic Muscle Bricks for Reconfigurable Musculoskeletal Robots

cs.RO ·2026-10-29 ·Qiyao Wang, Yinglei Zhu, Liang Zhou, Wenzhe Gong, Xin-Jun Liu +1 more
similarity 0.58
Abstract · 6 figures. Qiyao Wang and Yinglei Zhu contributed equally to this work. Improved HTML rendering of Figure 1; scientific content unchanged

Musculoskeletal robots combine compliant actuators with articulated skeletons, but exploring alternative configurations often requires repeated fabrication. We present MUSBRIC, a modular hardware platform and accompanying MuJoCo-based simulator for reconfigurable musculoskeletal robots. LEGO-compatible endcaps turn fiber-reinforced extensile pneumatic artificial muscles into reusable, plug-and-play muscle bricks that connect directly to standard LEGO components. Experimentally identified actuator behavior supports corresponding musculoskeletal simulations. An elbow-joint prototype validates load-dependent flexion and extension, showing that pulley-guided routing enables reversible motion and a mechanical stop stabilizes the straight posture. A robotic hand demonstrates compliant grasping and multi-joint construction. Matched hardware and simulation sweeps across 15 leg configurations demonstrate systematic exploration of attachment geometry, while a quadruped assembled from four legs demonstrates walking. Together, these demonstrations span mechanism analysis, configuration exploration, and functional robot construction within a single reconfigurable system. The hardware designs and simulation code will be released as open source soon to facilitate reproduction and further development.

0.35

Suspended-Fabric Robotic Manipulation Surfaces: Modelling, Design Space, and Multimodular Extensio

cs.RO ·2026-10-30 ·Pratik Ingle, Jørn Lambertsen, Kasper Støy, Andres Faiña
similarity 0.58
Abstract

Robotic Manipulation Surfaces (RMS) reposition objects by deforming the surface on which they rest. A recent class of RMS suspends a continuous fabric sheet from a sparse grid of vertical linear actuators lowering the actuator density of such surfaces but how to design such surfaces so that objects can be controlled everywhere on it, and how to extend it beyond a single module so that objects can pass between modules and achieve parallel, remain open. This paper presents a separable catenary model of the suspended sheet that is fast to compute and provides both the surface shape for given actuator heights and the actuator heights for a desired local slope. The closed form inverse lets a simple PID controller position objects on the sheet, and the model relates fabric length, module span and actuator stroke to the reachable workspace, yielding a minimum fabric length bound and design charts for these surfaces. The approach is then extended to a multimodular platform in which neighbouring modules share actuators. On a $2 \times 2$ prototype, we demonstrate that centimetre-scale objects are transferred between modules and positioned within 0.03 m over a $1 m^2$ workspace with only nine actuators, enabling multi-object manipulation and opening the way to parallel manipulation.

0.21

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.57
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14