CS Paper Radar

Compositional Aeroelastic Operators for Morphing Flexible Multibody Aircraft: A Geometric Framework with Structural Verification

Gelin Chen, Chen Song, Chao Yang

cs.CE math.NAphysics.flu-dyn ·submitted 2026-08-15 06:26 UTC · v1

Abstract

Morphing flexible multibody aircraft require structural strain, aerodynamic geometry, surface velocity, and generalized loading to remain compatible as joints and flexible components change configuration. A compositional formulation is developed around an assumed material attachment between each lifting surface and a geometrically exact beam. Separating the component root pose from the section field shows that the body strain and elastic potential of a component depend on its own elastic coordinates, while upstream motion enters kinetic terms and external-load pullbacks. At element level, an exact relative logarithm $d$ supplies strain and potential energy, whereas a reference-anchored section coordinate $σ$ supplies deformed section geometry. Finite-order expansions retain the finite reference geometry exactly and truncate only endpoint perturbations. The attachment map then generates surface points, tangents, normals, velocities, and force Jacobians from common section kinematics. Euler--Poincare beam balance, moving-surface potential-flow relations, graph cotangent assembly, and the associated semidiscrete power identity are stated in a common twist--wrench convention. Collocation, pressure, equivalent-load, and structural-station sites are distinguished to expose their approximation errors. Verification gives the expected $N_d+1$ convergence order for degree-$N_d$ relative-log expansions. In a geometrically nonlinear cantilever comparison, a cubic static-manifold correction reduces mean full-record displacement error from $0.479$ to $0.255$ over four completed load cases. These results provide structural and interface-level evidence rather than validation of a complete aircraft aeroelastic prediction.

Comment
30 pages, 2 figures, 2 tables

Closest papers

Nearest neighbours by meaning across the whole index.

Flexible-body Modeling, Kinematic Identification, and Assembly Accuracy of Overconstrained Spatial Linkages

cs.RO math.AG ·2026-09-15 ·Daniel Huczala, Michael Pieber, Johannes Gerstmayr, Andreas Mair, Frederik Schulte +4 more
similarity 0.60
Abstract

Overconstrained rational single-loop linkages are efficient, compact, and low-cost custom mechanisms, yet their deployment in industrial settings is limited. In simulations, rigid body formulations fail due to redundant constraints. This study presents a flexible multibody modeling framework based on the floating frame of reference formulation, and delivers an overall accuracy analysis of assembled linkages prototypes. The approach is validated against 3D-printed PLA prototypes of a Bennett four-bar mechanism, including variants with intentional joint-axis misalignment, which theoretically, from the rigid body point of view, cannot be assembled. A supplementary contribution is delivered in the form of a kinematic parameter identification methodology suited for this type of mechanism with ill-conditioned Jacobian. The experimental and simulation results are compared and reveal that these overconstrained mechanisms exhibit a self-assembling tendency -- structural compliance drives the assembly toward the ideal geometric configuration, distributing constraint stress throughout the structure. Additional qualitative demonstrations using cardboard tubes and bamboo sticks as link building blocks confirm that functional mechanisms can be realized from low-cost, unconventional materials with limited manufacturing accuracy. The proposed modeling pipeline is fully algorithmic and enables design optimization in the future.

0.18

Consistent Mapping for Fluid Structure Interaction with Geometrically Nonlinear Isogeometric Beams

cs.CE physics.comp-ph ·2026-11-09 ·Juan Ignacio Camarotti, Ricky Aristio, Roland Wüchner
benchmark similarity 0.59
Abstract

Isogeometric beam formulations provide an efficient reduced-dimensional representation of slender structures, combining accurate geometry and high-order continuity with few structural degrees of freedom. Their application to fluid--structure interaction (FSI) requires transferring motion and loads between the one-dimensional beam centerline and the surrounding fluid interface. While mapping strategies exist for conventional finite element beams, geometrically nonlinear isogeometric formulations require operators consistent with their spline-based kinematics and distinct descriptions of cross-sectional rotation. This work develops consistent beam-to-surface mappings for geometrically nonlinear isogeometric Bernoulli and Timoshenko beams in partitioned FSI. Fluid-interface points are attached to the beam in the reference configuration and reconstructed using the nonlinear kinematics of each formulation. Consistent linearization yields a configuration-dependent mapping operator whose transpose ensures work-conjugate load transfer. The formulations are verified through analytical deformation tests, convergence studies, and virtual-work checks, and evaluated in beam-based adaptations of the Mok and Turek--Hron benchmarks and the Goland wing flutter benchmark. The results confirm accurate interface reconstruction and work-conjugate load transfer under large deformations, while demonstrating the applicability of both beam formulations to coupled FSI problems.

0.28

Modular Inverse Dynamics and Wrench Recovery for Closed-Chain Mechanisms Using Path Assembly

cs.RO ·2026-10-15 ·Mohammad Dastranj, Jouni Mattila
similarity 0.55
Abstract

Rigid closed chains can admit indeterminate internal reactions even when their motion is fully specified. This paper develops a modular inverse-dynamics workflow that combines path-based motion reconstruction with recovery of uniquely determined actuator and joint-wrench outputs. Analytical second-order differentiation of assembled transformation paths supplies passive velocities and accelerations on a regular closure branch. Spatial Newton--Euler balances are then assembled over the physical body-and-joint graph. Established nullspace and dual criteria identify and recover unique outputs, while balance, ideal-joint admissibility and affine-family diagnostics assess nonunique reference reactions. Evaluation against Simscape Multibody uses prescribed motion of a seven-degree-of-freedom heavy-duty hybrid serial--parallel manipulator under common rigid-body, ideal-joint assumptions. The results show close agreement with the reference for passive positions, actuator efforts and uniquely recoverable constraint-wrench components. Reaction diagnostics support compatibility with the admissible numerical load family.

0.16

Aeroelastically Constrained Optimal Path Planning of a Fixed-Wing Airborne Wind Energy System

eess.SY ·2026-11-10 ·Omid Heydarnia, Jolan Wauters, Tom Lefebvre, Joris Degroote, Guillaume Crevecoeur
published similarity 0.53
Abstract

Multi-megawatt fixed-wing airborne wind energy systems (AWES) use an aircraft with large, slender wings that deform over the pumping cycle. To harvest maximum energy, the cycle is usually designed by means of dedicated reference trajectory optimization routines. It is well known that such routines rely heavily on the system model and that close alignment between the model and the physical system is required for the results to hold in practice. Nevertheless, the wing is usually treated as rigid and structural limits are respected indirectly through upper bounding of states and inputs. In this work, we directly enforce bounds on the elastic deflection and twist of the wing in the power-maximizing periodic optimal control problem. To that end, we model the wing by root-clamped modes, loaded by strip-theory aerodynamics and by the gravitational and inertial loads of the manoeuvring aircraft. To keep the problem tractable, the modal dynamics are replaced by their quasi-static equilibrium, which enters every discretization interval as algebraic constraints. For a multi-megawatt reference aircraft, the elastic twist near the wing tips reaches $1.03^\circ$ along the optimal rigid-wing trajectory. With a twist limit of $0.6^\circ$, the optimal trajectory delivers $31\,\%$ less mean power than the rigid-wing one, mainly through a lower tether tension during reel-out. Rigid-wing trajectory optimization can thus overestimate the power that the wing limits permit. Forward simulations that retain the modal dynamics demonstrate that the quasi-static deflection and twist deviate from the dynamic ones by less than $2\,\%$ of their limits. This work shows that elastic deformation can be accounted for in the trajectory optimization and that, depending on the wing limits, it can strongly reduce the achievable power.

0.32

Structural Affinity: An Algorithm for Coherent Cage-Based Shape Design

cs.LG cs.GRcs.RO ·2026-10-16 ·Aviraj Newatia, Shengan Yang, Hantao Zhong, Rika Antonova
similarity 0.52
Abstract · 27 pages, 16 figures

Cage-based deformation (CBD) parametrises 3D geometry through a small set of control handles, effectively enabling a variety of tasks from animation and interactive modelling to tool-based co-design, neural deformation transfer, and aerodynamic shape optimization. Many optimization approaches relying on CBD employ regularisation strategies to reduce the distortion of the deformed mesh by encouraging smooth, regular cage deformations. These techniques offer soft guidance to an optimization algorithm towards desirable deformations, but compete with the task objective rather than changing the deformation parameterization itself. In this work we introduce Structural Affinity for CBD, an explicit regularisation method which enables smooth deformations through control cages by exploiting a two-cage structure to couple cage-handle motion directly. Structural Affinity precomputes an affinity matrix using mean-value coordinates, binding the inner control-cage to a coarser outer-cage. This matrix defines how much a cage handle displacement propagates to neighbouring handles which substantially decreases and often eliminates cage self-intersections, reduces mesh distortion, and adds linear overhead at deformation time. Across robotic control--morphology co-design, source-to-target neural deformation transfer, and aerodynamic wing shape optimization, Structural Affinity produces more regular deformations and substantially reduces reliance on hand-designed structural loss terms. We report consistent gains on three complementary diagnostics: the cotangent Laplacian, a proxy for surface smoothness; cage distortion, capturing whether control handles move coherently; and surface roughness, which measures undesirable oscillation in wing geometry.

0.24

A Morphing Aerial Robot With Thruster-Integrated Flexible Continuum Links for Shape Adaptive Aerial Manipulation

cs.RO ·2026-09-16 ·Eri Sawada, Kazuki Sugihara, Ayano Miyamichi, Kunio Kojima, Kei Okada
published similarity 0.51
Abstract · Accepted to 2026 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS)

In recent years, aerial manipulation has attracted increasing attention as a key to expand the application of aerial robots. In this work, we focus on two major research directions for achieving versatile aerial manipulation: (i) acquiring high environmental adaptability using soft manipulators, and (ii) expanding the feasible wrench space by distributing thrusters along the manipulator. However, no aerial robot has simultaneously satisfied these two requirements. Therefore, in this paper, we propose a morphing rotor-distributed aerial robot with flexible continuum links that achieves both high shape adaptability and an expanded wrench space. The flexible continuum links function as soft manipulators, passively conforming to the shape of the environment, while the thrusters distributed along the continuum links expand the feasible thrust wrench space and enable the end-effector to exert large interaction forces. To realize the proposed robot, it is essential to suppress vibrations of the lightweight continuum links. Thus, we develop a composite leaf-spring structure that provides both high torsional and vertical stiffness, and vibration-suppressing control methods. Using these implementations, we demonstrate stable flight and a variety of aerial manipulation tasks. To the best of our knowledge, this is the first work to realize aerial manipulations using flexible links with an integrated thruster.

0.29

Manipulation with Stability Guarantees: Linear Deformable Objects with Non-negligible Physical Response Grasped at Multiple Location

cs.RO ·2026-09-22 ·Daniel Feliu-Talegon, Cosimo Della Santina
similarity 0.51
Abstract · 19 pages, 13 figures

Most research on the manipulation of deformable objects focuses on lightweight systems with negligible mechanical response, effectively restricting attention to quasi-static regimes. This assumption excludes a broad class of practically relevant objects, such as hoses, pipes, and wiring harnesses, whose dynamics cannot be ignored during manipulation. In this work, we address this limitation by introducing a closed-loop control architecture that explicitly accounts for object dynamics and recasts manipulation as a shape-regulation problem. Control is achieved by modulating forces and torques applied at multiple fixed points along the object. This approach builds on three methodological contributions: a fully dynamic model of linear deformable objects based on discrete strain parameterizations; an extension of the notion of actuation coordinates to SE(3), yielding a structured and inherently underactuated control architecture; and nonlinear feedback strategies providing explicit conditions for steady-state convergence to desired configurations. Extensive simulations on representative manipulation tasks demonstrate the performance gains enabled by the proposed modelbased formulation. We finally validate the approach experimentally through a real-time closed-loop implementation with online shape estimation, confirming its practical feasibility and effectiveness

0.33

A space-time finite element formulation for geometrically exact shear-deformable beams

cs.CE math.NA ·2026-10-02 ·Ivo Steinbrecher, Alexander Humer
similarity 0.51
Abstract

We present a space-time finite element formulation for the transient analysis of geometrically exact shear-deformable beams. The formulation treats space and time within a unified finite element framework and employs a mixed approach in which translational and angular velocities are introduced as independent fields. The rotation field is parametrized using nodal rotation (pseudo-)vectors and a suitable objective interpolation of the triad field is employed. The resulting formulation supports generally curved beam structures, including geometric kinks and rigid joints. Furthermore, time-dependent material domains can be represented directly through the geometry of the space-time surface, enabling the treatment of non-material boundaries without modifying the underlying beam formulation. Numerical examples demonstrate convergence to solutions obtained with classical time-stepping schemes, objectivity of the formulation, and the influence of the space-time stabilization. Finally, the sliding spaghetti problem illustrates the applicability of the proposed approach to axially moving continua.

0.19