CS Paper Radar

Aeroelastically Constrained Optimal Path Planning of a Fixed-Wing Airborne Wind Energy System

Omid Heydarnia, Jolan Wauters, Tom Lefebvre, Joris Degroote, Guillaume Crevecoeur

eess.SY ·submitted 2026-11-10 07:28 UTC · v1
published

Abstract

Multi-megawatt fixed-wing airborne wind energy systems (AWES) use an aircraft with large, slender wings that deform over the pumping cycle. To harvest maximum energy, the cycle is usually designed by means of dedicated reference trajectory optimization routines. It is well known that such routines rely heavily on the system model and that close alignment between the model and the physical system is required for the results to hold in practice. Nevertheless, the wing is usually treated as rigid and structural limits are respected indirectly through upper bounding of states and inputs. In this work, we directly enforce bounds on the elastic deflection and twist of the wing in the power-maximizing periodic optimal control problem. To that end, we model the wing by root-clamped modes, loaded by strip-theory aerodynamics and by the gravitational and inertial loads of the manoeuvring aircraft. To keep the problem tractable, the modal dynamics are replaced by their quasi-static equilibrium, which enters every discretization interval as algebraic constraints. For a multi-megawatt reference aircraft, the elastic twist near the wing tips reaches $1.03^\circ$ along the optimal rigid-wing trajectory. With a twist limit of $0.6^\circ$, the optimal trajectory delivers $31\,\%$ less mean power than the rigid-wing one, mainly through a lower tether tension during reel-out. Rigid-wing trajectory optimization can thus overestimate the power that the wing limits permit. Forward simulations that retain the modal dynamics demonstrate that the quasi-static deflection and twist deviate from the dynamic ones by less than $2\,\%$ of their limits. This work shows that elastic deformation can be accounted for in the trajectory optimization and that, depending on the wing limits, it can strongly reduce the achievable power.

DOI
10.13140/RG.2.2.31520.34567

Closest papers

Nearest neighbours by meaning across the whole index.

Extensions to the Dubins Airplane Method - Flight Performance Constraints in Uniform Wind

eess.SY ·2026-11-05 ·Simon Schopferer
top venue similarity 0.57
Abstract

This paper extends the Dubins Airplane Method to generate trajectories for fixed-wing aircraft that remain within flight performance limits in the presence of uniform wind. Within the field of runtime-efficient trajectory generation for fixed-wing aircraft, the Dubins Airplane Method represents a well-received and widely adopted compromise between algorithmic complexity, runtime efficiency, and solution quality. However, its simplistic kinematic model restricts its ability to generate safe and feasible trajectories, especially in the presence of wind. As a mathematical foundation to overcome these limitations, a set of closed-form equations are derived that relate flight performance constraints to kinematic constraints. Building upon existing methods that use trochoids for planning of 2D trajectories in uniform wind, this paper presents a set of iterative algorithms for planning versatile 3D trajectories composed of trochoidal or circular turns and straight flight segments, with constant vertical speed, constant thrust or smooth longitudinal transitions. The presented methods comprise a flexible and modular framework for runtime-efficient generation of performance-aware trajectories based on parametric curves without the need for numerical trajectory representations.

0.43

Safe Receding-Horizon Control of Fixed-Wing Aircraft Using Constrained Approximate Dynamic Programming

eess.SY ·2026-10-05 ·Felipe Arenas-Uribe, Ricardo Gutierrez, Jesse B. Hoagg
similarity 0.55
Abstract

We present a receding-horizon optimal control for fixed-wing aircraft subject to state constraints. These constraints include operational constraints such as altitude, geofencing, and obstacle avoidance, as well as bounds on flight-path angle, roll angle, and airspeed. The state constraints are composed into a single soft-minimum control barrier function (CBF). We use this composite CBF in a constrained-approximate dynamic program to obtain a sequence of analytic closed-form control functions that approximately minimize a quadratic finite-horizon integral cost subject to the CBF constraint. The resulting receding-horizon control is non-myopic in the sense that it approximately optimizes the integral cost while satisfying the state constraint at all times along the entire prediction horizon. We demonstrate constraint satisfaction and performance in simulations of a fixed-wing aircraft navigating an obstacle-filled airspace under wind uncertainty. We also compare this receding-horizon control with 2 other methods.

0.14

Time-Optimal Control of One-Mode Flexible Structures: Analytical Solution and the Cost of Flexibility

eess.SY math.OC ·2026-08-11 ·Manuel Keppler
similarity 0.55
Abstract

The time-optimal solution for a double integrator is a foundational result: its time-displacement law $T_r = 2\sqrt{L}$ for a normalized step $L$ is structure that numerical methods cannot provide. We solve the time-optimal control for rest-to-rest maneuvers of a double integrator coupled to a harmonic oscillator, deriving the first analytical solution and closed-form time-displacement law. Synthesis reduces to a single scalar inversion. This is the model to which the two-mass-spring system, the one-bending-mode flexible structure, and the linearized overhead crane reduce. A Pythagorean identity $T^2 = T_r^2 + 2T_s^2$ decomposes the optimal maneuver time into the rigid-body minimum and a synchronization time $T_s \leq π$, the cost of flexibility, giving the sharp envelope $2\sqrt{L} \leq T \leq 2\sqrt{L + π^2/2}$. The penalty is scale-dependent. For small maneuvers $T \propto L^{1/4}$: one oscillator mode costs as much as two additional integrators. For large ones, flexibility is asymptotically free. It vanishes at the natural motions, where the oscillator completes whole cycles. A closed-form sensitivity formula proves the maneuver time non-monotone in stiffness. Adding flexibility to a rigid body never shortens a maneuver, yet softening an already flexible structure can: stiffer is not always faster. The natural motions are robust design targets since first-order sensitivity to stiffness vanishes there.

0.04

COAST: Safe Flight Corridor Planner for Fast and Robust Snap Minimized Trajectories

cs.RO eess.SY ·2026-11-17 ·Alejandro Pelaez, Randal W. Beard
code/data similarity 0.54
Abstract · 14 pages, 4 figures, 2 tables. Submitted to the 2027 American Control Conference (ACC 2027)

Current B-Spline trajectory planners face a critical trade-off: they either sacrifice computational speed to maintain strict Safe Flight Corridor (SFC) guarantees, or they abandon hard safety bounds in favor of soft-constraint penalties to achieve real-time performance. We present COAST (Corridor-Optimized Aerially-Safe Trajectories), a B-Spline based, online trajectory planner capable of formulating snap minimized trajectories with SFC guarantees. COAST divides the problem into two stages: an A* based front-end that generates geometrically simple SFCs (represented as a chain of rectangular prisms), and a quadratic programming back-end for control point optimization. To handle the non-convexity of SFC intersections, we leverage the finite support property of B-Splines, to ensure the spline never exits SFC boundaries. The control point optimization incorporates MINVO transforms for kinodynamic bounding, allowing COAST to design non-conservative, dynamically feasible trajectories, while a snap minimization matrix calculation provides flight smoothness. This formulation provides a formal geometric containment guarantee, while ensuring mean trajectory computation times under 5 ms for real-time deployment. We validate our results through high-fidelity simulation experiments. The source code can be found at: https://github.com/byu-magicc/Minimum-Snap-Trajectories

0.46

Control Allocation with Adaptive Augmentation for Aerodynamic Optimization of Trailing Edge Morphing Aircraft

eess.SY math.OC ·2026-10-01 ·Mark Spiller, Lennart Kracke, Johannes Autenrieb
similarity 0.54
Abstract · Submitted to American Control Conference (ACC) 2027

This paper presents a control allocation framework with adaptive augmentation for a trailing edge morphing aircraft, providing stability guarantees under uncertainty while exploiting the available morphing degrees of freedom to optimize aerodynamic efficiency. A baseline controller is designed using the nominal aircraft model to establish the desired closed-loop reference dynamics. For the aerodynamics, the wing shape is optimized dependent on the flight state to achieve a target elliptical lift distribution corresponding to minimum induced drag. The adaptive augmentation is tailored to the control allocation problem to account for the uncertain system dynamics and stabilize the aircraft around the reference dynamics. The resulting stabilization condition is formulated as hard constraint in the allocation problem while minimizing deviations from the corresponding state-dependent aerodynamically optimal wing shape. Numerical results demonstrate that the adaptive augmentation compensates for matched uncertainties while the control allocation optimizes the wing shape with respect to the reference elliptical lift distribution.

0.18

Model Predictive Control of Wind Turbines: A Model-Oriented Review of Prediction Models, Control Objectives, and Nonlinear Aerodynamic Formulations

eess.SY math.DSmath.OC ·2026-10-22 ·Roya Khalili-Amirabadi, Mohsen Jalaeian-Farimani, Mahdi Ghane
published similarity 0.53
Abstract · Khalili-Amirabadi, R., Jalaeian-Farimani, M., & Ghane, M. (2026). Model Predictive Control of Wind Turbines: A Model-Oriented Review of Pred…

Model predictive control (MPC) has been applied to wind-turbine regulation with markedly different internal prediction models, ranging from linearized low-order turbine models to nonlinear, aeroelastic, floating, and data-driven predictors. This review organizes the literature primarily by the model propagated by the controller and treats model order, predictor representation, MPC formulation, control objective, and validation plant as separate descriptors. Primary studies show that low-order linear or piecewise-affine predictors are attractive for constrained power and speed regulation, whereas flexible drivetrain, structural, and floating models are needed when drivetrain twist, tower motion, blade loads, or platform dynamics are explicit control quantities. Nonlinear and economic MPC studies further demonstrate coordinated pitch/torque control across broad operating regions, while preview, repetitive, and data-driven formulations address wind prediction, periodic loads, and model mismatch. Particular attention is given to aerodynamic pitch dependence: variable-pitch turbine dynamics can be non-affine with respect to applied pitch, and the term NMPC alone does not prove that the original nonlinear pitch map is retained inside the optimizer. The review therefore adopts a conservative, equation-based classification for direct nonlinear applied-pitch propagation. Here, direct nonlinear applied-pitch propagation means that the applied pitch at each prediction step is evaluated inside the original nonlinear aerodynamic map, rather than replacing that dependence by a linearized, scheduled, piecewise-affine, or learned surrogate. The literature supports a remaining integration challenge at the intersection of flexible drivetrain prediction, nonlinear aerodynamic pitch treatment, explicit constraints and load objectives, and validated adaptive or learned model correction.

0.35

Compositional Aeroelastic Operators for Morphing Flexible Multibody Aircraft: A Geometric Framework with Structural Verification

cs.CE math.NAphysics.flu-dyn ·2026-08-15 ·Gelin Chen, Chen Song, Chao Yang
similarity 0.53
Abstract · 30 pages, 2 figures, 2 tables

Morphing flexible multibody aircraft require structural strain, aerodynamic geometry, surface velocity, and generalized loading to remain compatible as joints and flexible components change configuration. A compositional formulation is developed around an assumed material attachment between each lifting surface and a geometrically exact beam. Separating the component root pose from the section field shows that the body strain and elastic potential of a component depend on its own elastic coordinates, while upstream motion enters kinetic terms and external-load pullbacks. At element level, an exact relative logarithm $d$ supplies strain and potential energy, whereas a reference-anchored section coordinate $σ$ supplies deformed section geometry. Finite-order expansions retain the finite reference geometry exactly and truncate only endpoint perturbations. The attachment map then generates surface points, tangents, normals, velocities, and force Jacobians from common section kinematics. Euler--Poincare beam balance, moving-surface potential-flow relations, graph cotangent assembly, and the associated semidiscrete power identity are stated in a common twist--wrench convention. Collocation, pressure, equivalent-load, and structural-station sites are distinguished to expose their approximation errors. Verification gives the expected $N_d+1$ convergence order for degree-$N_d$ relative-log expansions. In a geometrically nonlinear cantilever comparison, a cubic static-manifold correction reduces mean full-record displacement error from $0.479$ to $0.255$ over four completed load cases. These results provide structural and interface-level evidence rather than validation of a complete aircraft aeroelastic prediction.

0.10

Real-Time Bounded Catenary Solver for UAV Tether Modeling

cs.RO ·2026-09-16 ·Max Beffert, Andreas Zell
similarity 0.53
Abstract

For non-stationary tethered multirotor UAVs in real-world conditions, simulating the forces imposed on the drone by the aerodynamic drag of the tether becomes crucial, with online use cases placing a hard bound on the maximum solve time. In previous work, a quasi-analytical catenary tether model reached a mean solve time of 0.51 ms using a general-purpose root finder, but without any worst-case guarantees or proven convergence. In this work, we reformulate the inner solver by reducing the catenary boundary-value problem to a single transcendental equation in one well-conditioned unknown. We derive a closed-form bracket and prove monotonicity and convexity as well as existence and uniqueness of the root, which together guarantee convergence of the solver. We further propose a two-regime initial guess which approximates the true root within 3.4 % and reduces the mean iteration count by 69.2 % to 2.24 compared to the textbook initialization. Building on the hybrid root-finding method rtsafe (Newton-Raphson with bisection fallback giving bounded iteration counts), we implement a specialized variant that exploits the problem structure to omit unnecessary checks while retaining correctness, which gives up to 1.37 times speedup. With the proposed solver the full tether model achieves a nearly constant solve time of 4.0 us on average and 4.6 us at worst, a 68 times speedup over an optimized re-implementation of the previous method, while agreeing with it to a relative deviation of 8.7e-9. Because the reformulation leaves the underlying physical model untouched, the experimental validation of the previous work carries over unchanged. We further demonstrate its suitability for embedded, resource-constrained platforms with a Lua implementation running directly in ArduPilot on a drone's flight controller, where it stays well inside the scheduling budget with a mean solve time of 0.74 ms.

0.22