CS Paper Radar

Detachable Wire Drive : Reconfigurable Robot Architecture with Shared Actuators

Takahiro Hattori, Kento Kawaharazuka, Kei Okada

cs.RO ·submitted 2026-08-16 00:49 UTC · v1
published

Abstract

Reconfigurable robots offer significant potential for adapting to diverse tasks; however, conventional centralized architectures often require dedicated actuators for each module, leading to substantial increases in overall system weight, volume, and cost. To address these challenges, this paper presents the "Detachable Wire Drive," a reconfigurable robotic system that enables the sharing of heavy and expensive actuators across various morphologies. The core of this system is the "Wire Detach Unit," a mechanism designed to physically split and reconnect wire drive paths, allowing motors to be consolidated into a common base unit. We demonstrate the versatility of this approach by developing a 2-DOF rigid arm, a continuum arm, and two distinct grippers, all of which are interchangeably attached to, and driven by, a single shared actuator set. Experimental results validate the mechanical reliability of the detachment process and the control framework's ability to seamlessly manage transitions between configurations, highlighting a path toward more efficient and multi-functional robotic systems.

Comment
Accepted at IROS2026, website - https://hatofly.github.io/detachable-wire-drive/

Closest papers

Nearest neighbours by meaning across the whole index.

Tensegrity Continuum Robots Enable Task-Adaptive Morphologies for Cooperative Behaviors

cs.RO ·2026-08-27 ·Mahmud Hasan Saikot, Sydney Spiegel, Sudheera Akalanka Kariyawasam, Andrew Stefka, Josh Chrisler +1 more
top venue similarity 0.70
Abstract · 22 pages, 6 figures, Accepted to Nature Machine Intelligence

Robots that can change their morphologies and behaviors for different tasks and environments hold great promise for adaptable, multifunctional systems. Modular reconfigurable robots (MRRs) can achieve such functionalities by docking and rearranging individual units, but most rely on rigid modules that lack structural compliance, resulting in limited capabilities. Continuum robots offer compliance through flexible backbones, yet they cannot self-reconfigure into task-adaptive multi-robot configurations. Here, we introduce an MRR that unifies the advantages of both architectures by combining a tensegrity-based compliant body with claw-based connection mechanisms. Each robot can manipulate and locomote independently, and multiple robots can self-reconfigure into different morphologies (e.g., chains, loops, branches) for cooperative manipulation and locomotion. We demonstrate the robots' capability across diverse tasks and environments, including coordinated object manipulation and transport, multimodal locomotion, and loco-manipulation in real-world scenarios. These results lay a foundation for adaptable and multifunctional robotic collectives, with broad potential applications in manufacturing, space exploration, and search-and-rescue operations.

0.33

Recompositional Robotics: Cross-Domain, Open-set, and Lifelong Modularity Beyond Morphology

cs.RO ·2026-09-29 ·Steven Swanbeck, Jonathan Salfity, Corrie Van Sice, Robert Blake Anderson, Mitch Pryor
published similarity 0.63
Abstract · 2026 IEEE/RSJ IROS Workshop on Reconfigurable Modular Robots

Research in modular robotics has produced capable approaches allowing a robot's morphology to change online, with recent efforts also developing approaches to decide which morphology to assume and automatically propagate that decision into the robot's motion planning and control. These approaches are powerful and increase adaptability in the field. However, an alternative objective is not to build robots whose structures can change, but robots whose fundamental capabilities can change, where capability is a joint function across several domains, including kino-dynamics, perception, compute, and high-level coordinating behaviors. A robot designed to be reconfigured across these domains has a greater capacity to alter its capability than one that can be reconfigured in a single domain. We refer to this cross-domain reconfigurability as integration span, and recognize a complementary measure of the resistance to reconfiguration, which we refer to as integration inertia. Current modular robots have reduced integration inertia in the structural domain while it remains high in the other domains that contribute to integration span. We assert that the systems that can provide the most utility through reconfiguration in practice are those maximizing span and minimizing inertia and call this general problem recompositional robotics: adaptation over a heterogeneous set of modules including hardware, software, compute, and behavior that abstracts each component by the interfaces it requires and provides such that they can be reasoned over holistically. We define the problem, ground it in two deployed systems and active research efforts, and pose open questions about the future of recompositional robotics.

0.28

Design and Characterization of a Unified Continuum Robot Actuation Platform

cs.RO ·2026-10-14 ·Yunti Xu, Aedan Mangan, Miheer Potdar, Alex Lu, Tania K. Morimoto
similarity 0.61
Abstract

Continuum robots enable dexterous access to confined spaces in applications such as minimally invasive surgery and industrial inspection. However, their actuation systems are often custom-designed for specific robot architectures and tasks, limiting reuse across publications, institutions, and applications. This paper presents a unified actuation platform that decouples actuation hardware and software from continuum robot design. The platform provides modular actuation across continuum robot classes, scales to a large number of degrees of freedom (DOFs), and integrates with conventional serial manipulators for hybrid architectures. We validate the platform on an open-sourced surgical robotic system and experimentally characterize the actuation modules, achieving sub-millimeter translational accuracy and less than $5^\circ$ rotational error over ranges of $30$~mm and $180^\circ$, respectively. We further demonstrate the platform in two surgical use cases: teleoperation of a continuum camera in a constrained environment and bimanual manipulation using $2.53$~mm concentric-tube-robot-based forceps alongside a conventional wristed instrument. All hardware designs and ROS-based software are open-sourced to facilitate reuse and further research in continuum and surgical robotics.

0.31

A Conveyor Belt Mechanism for Repositionable Magnetic Coupling Between Continuum Robots

cs.RO ·2026-10-29 ·Ella Walsh, Eric Diller, Jessica Burgner-Kahrs
similarity 0.61
Abstract · 7 pages, 10 figures

This work proposes a novel conveyor belt mechanism enabling continuous, active repositioning of functional elements along the body of a tendon-driven continuum robot. Up to three conveyor belt mechanisms are integrated within a 9 mm diameter continuum robot. We demonstrate equivalent or reduced conveyor belt actuation forces compared to robot tendon actuation forces. As a case study, we mount permanent magnets along two conveyor belts, and demonstrate actively reconfigurable inter-robot coupling. Coupling point location and quantity can be adjusted during robot operation to actively tune the effective stiffness of the coupled multi-robot system. We show that effective stiffness follows a predictable inverse-cubic relationship with coupling location, and increases with the number of coupling points. These findings demonstrate that the conveyor belt mechanism enables active functional element repositioning for changing tasks requirements, with magnetic inter-robot coupling as one proof-of-concept.

0.28

Enabling Tidying Tasks in Robotic Vacuum Cleaners via a Geometry-Induced Self-Locking Deployable Linkage

cs.RO eess.SY ·2026-10-14 ·Eunseok Song, Jinwoong Kim, Sohee Lim, Taehyeong Kim, Yongkook Kim +3 more
similarity 0.61
Abstract · 8 pages, 6 figures, 1 table. v2: corrected author name, added minor revisions

Robotic vacuum cleaners must extend their functionality within tight limits on size, cost, and durability. Deployable linkages with few actuators meet these limits, but their backdrivability makes it difficult to hold a load-bearing posture without continuous motor torque. We introduce a two-stage deployable linkage that locks through its own geometry. At full deployment, an internal three-link subchain approaches a collinear, near-singular configuration in which the input-output transmission ratio tends to zero; plate loads therefore leave only a small residual back-driving torque, which drive-train friction and a lightweight magnetic detent absorb. A single actuator performs deployment and locking, a passive chassis-mounted trigger releases the lock for retraction, and a second actuator adjusts only the deployment height. We integrate the mechanism into a commercial robotic vacuum cleaner and validate it through a 100-cycle repeatability test, a quasi-static load test in which the locked plate held 50 N with the motor de-energized, and 140 pushing-type tidying trials on seven household objects against a commercial arm-equipped vacuum robot. We derive the analytical holding condition and discuss its limits as an intermediate design point between passive compliance and articulated manipulation.

0.24

SwapBot: Tool-Centric Robot Manipulation via Interchangeable End-Effectors and Tactile Sensing

cs.RO ·2026-10-29 ·Yunchu Zhang, Ray Song, Junhan Jiao, Liyiming Ke, Yuchen Yang +4 more
similarity 0.61
Abstract

Robot manipulation in everyday environments inherently involves substantial tool usage. Seemingly simple household tasks, such as cooking pan-fried tofu, require forceful cutting, delicate brushing, and precise placement using different tools under contact-rich interaction. Thus, the ability to autonomously swap and use task-appropriate tools is important for tool-centric manipulation. We introduce SwapBot, a modular, tool-centric end effector system featuring low-cost adapters that quickly convert common household tools into robot end effectors. Rather than pursuing a single universal gripper, SwapBot adopts a unified design principle that combines a fixed robot-side coupling interface with low-cost, tool-side adapters, enabling compatibility with diverse tools, including articulated ones, and multiple robot platforms. Each adapter integrates compact tactile sensors, supports fast autonomous swapping, and interfaces with an intuitive teleoperation system for efficient demonstration collection. User studies show that, during teleoperation, SwapBot reduces task completion time and operator workload. Using collected demonstrations on the robot, we train imitation learning policies to successfully perform tool-centric tasks like cooking tofu, stirring salad, flipping meat. Our ablation study shows that using tactile-augmented demonstrations improves policy performance across contact-rich skills, increasing success rates by 15 to 25 percentage points over RGB-only policies. These results highlight modular, tactile-equipped tools as a practical and extensible pathway toward robust and capable robot manipulation. Project website https://personalrobotics.github.io/SwapBot.

0.29

CuBot-STT: Simultaneously Transport and Tighten for Lattice-type Modular Reconfiguration Robot

cs.RO ·2026-10-29 ·Chongxi Meng, Da Zhao, Yanmin Zhou, Runjie Shen, Zhipeng Wang +1 more
theory similarity 0.60
Abstract · 11 pages. Submitted to IEEE/ASME Transactions on Mechatronics

Lattice-type modular reconfigurable robots rearrange standardized modules across tasks. Dedicated transport robots reduce module weight and cost by eliminating module level reconfiguration actuators. But existing systems use low capacity connections or internal fastening robots that occupy space for functional components. This paper presents CuBot-STT, which integrates module transport, interface locking, and release in one external robot. Cubic modules provide structural support and $24\,\mathrm{V}$ power distribution. On each face, a gear transmission converts one external input into motion of four helical locking points, preserving internal space. The robot uses alternating foot support, a gripper for module handling, and a tightening head for interface actuation. The controller coordinates two-foot support and module locking through continuous constraint transfers. The planner decomposes relocation costs into an analytical lower bound and a residual learned through expert-guided, goal conditioned Q-learning. Contact face $A^*$ search expands relocation sequences into robot primitives satisfying connectivity, asymmetric manipulation, and foot stance constraints. Experiments demonstrate normal and tangential interface capacities of $300\,\mathrm{N}$ and $490\,\mathrm{N}$, electrical continuity across six modules, and autonomous reconfiguration of an 11-module lattice. Planning benchmarks show superior search efficiency over analytical guidance and bidirectional heuristic search, with generalization beyond training lattice sizes without fine-tuning.

0.32

Extending Wire-Driven Parallel Robots to Multi-Floating-Link Systems with an Inter-Body Wire

cs.RO ·2026-10-12 ·Shintaro Inoue, Kento Kawaharazuka, Temma Suzuki, Sota Yuzaki, Keita Yoneda +1 more
top venue similarity 0.60
Abstract · Accepted to IEEE Robotics and Automation Letters, website: https://shin0805.github.io/twinx_multi_floating_link/

Parallel wire-driven systems are a framework in which multiple wires are connected to an end effector, and the end effector is driven by the tensions of those wires. Because they can transmit large forces, up to the breaking strength of the wires, over lengths on the order of several tens of meters, they can realize powerful actuation in large workspaces. In recent years, studies have also investigated connecting wires to external environments such as trees and columns and forming parallel wire actuation on site. However, conventional parallel wire-driven systems often assume a single end effector, and because of interference between wires and links in a shared workspace, it has been difficult to handle multiple floating links simultaneously. In this study, we realize multi-floating-link parallel wire actuation by introducing an inter-body wire. In real-robot experiments, the two bodies supported and lifted a mannequin and transferred it onto a stretcher as a rescue motion. This shows that parallel wire actuation can be extended from a single end effector to a multi-floating-link system, and indicates its potential for broader tasks such as the manipulation of large objects and rescue support.

0.48