CS Paper Radar

CuBot-STT: Simultaneously Transport and Tighten for Lattice-type Modular Reconfiguration Robot

Chongxi Meng, Da Zhao, Yanmin Zhou, Runjie Shen, Zhipeng Wang, Bin He

cs.RO ·submitted 2026-10-29 03:30 UTC · v1
theory

Abstract

Lattice-type modular reconfigurable robots rearrange standardized modules across tasks. Dedicated transport robots reduce module weight and cost by eliminating module level reconfiguration actuators. But existing systems use low capacity connections or internal fastening robots that occupy space for functional components. This paper presents CuBot-STT, which integrates module transport, interface locking, and release in one external robot. Cubic modules provide structural support and $24\,\mathrm{V}$ power distribution. On each face, a gear transmission converts one external input into motion of four helical locking points, preserving internal space. The robot uses alternating foot support, a gripper for module handling, and a tightening head for interface actuation. The controller coordinates two-foot support and module locking through continuous constraint transfers. The planner decomposes relocation costs into an analytical lower bound and a residual learned through expert-guided, goal conditioned Q-learning. Contact face $A^*$ search expands relocation sequences into robot primitives satisfying connectivity, asymmetric manipulation, and foot stance constraints. Experiments demonstrate normal and tangential interface capacities of $300\,\mathrm{N}$ and $490\,\mathrm{N}$, electrical continuity across six modules, and autonomous reconfiguration of an 11-module lattice. Planning benchmarks show superior search efficiency over analytical guidance and bidirectional heuristic search, with generalization beyond training lattice sizes without fine-tuning.

Comment
11 pages. Submitted to IEEE/ASME Transactions on Mechatronics

Closest papers

Nearest neighbours by meaning across the whole index.

Tensegrity Continuum Robots Enable Task-Adaptive Morphologies for Cooperative Behaviors

cs.RO ·2026-08-27 ·Mahmud Hasan Saikot, Sydney Spiegel, Sudheera Akalanka Kariyawasam, Andrew Stefka, Josh Chrisler +1 more
top venue similarity 0.60
Abstract · 22 pages, 6 figures, Accepted to Nature Machine Intelligence

Robots that can change their morphologies and behaviors for different tasks and environments hold great promise for adaptable, multifunctional systems. Modular reconfigurable robots (MRRs) can achieve such functionalities by docking and rearranging individual units, but most rely on rigid modules that lack structural compliance, resulting in limited capabilities. Continuum robots offer compliance through flexible backbones, yet they cannot self-reconfigure into task-adaptive multi-robot configurations. Here, we introduce an MRR that unifies the advantages of both architectures by combining a tensegrity-based compliant body with claw-based connection mechanisms. Each robot can manipulate and locomote independently, and multiple robots can self-reconfigure into different morphologies (e.g., chains, loops, branches) for cooperative manipulation and locomotion. We demonstrate the robots' capability across diverse tasks and environments, including coordinated object manipulation and transport, multimodal locomotion, and loco-manipulation in real-world scenarios. These results lay a foundation for adaptable and multifunctional robotic collectives, with broad potential applications in manufacturing, space exploration, and search-and-rescue operations.

0.33

Detachable Wire Drive : Reconfigurable Robot Architecture with Shared Actuators

cs.RO ·2026-08-16 ·Takahiro Hattori, Kento Kawaharazuka, Kei Okada
published similarity 0.60
Abstract · Accepted at IROS2026, website - https://hatofly.github.io/detachable-wire-drive/

Reconfigurable robots offer significant potential for adapting to diverse tasks; however, conventional centralized architectures often require dedicated actuators for each module, leading to substantial increases in overall system weight, volume, and cost. To address these challenges, this paper presents the "Detachable Wire Drive," a reconfigurable robotic system that enables the sharing of heavy and expensive actuators across various morphologies. The core of this system is the "Wire Detach Unit," a mechanism designed to physically split and reconnect wire drive paths, allowing motors to be consolidated into a common base unit. We demonstrate the versatility of this approach by developing a 2-DOF rigid arm, a continuum arm, and two distinct grippers, all of which are interchangeably attached to, and driven by, a single shared actuator set. Experimental results validate the mechanical reliability of the detachment process and the control framework's ability to seamlessly manage transitions between configurations, highlighting a path toward more efficient and multi-functional robotic systems.

0.39

GeoTrussRover: Morphological Computation with Contact-Semantic Control Primitives

cs.RO cs.GRcs.NEeess.SY ·2026-09-10 ·Muyuan Ma, Yi Zhang, Yang Yang, Xuanyan Zheng, Ruiqi Hu +10 more
similarity 0.58
Abstract

Reconfigurable robots can change their contact geometry when a fixed body cannot negotiate an obstacle. A variable-geometry truss (VGT) distributes this shape change through a load-bearing structure, but coupling it to a mobile base creates a high-dimensional coordination problem. GeoTrussRover combines an electrically actuated VGT, a wheeled base, and contact-semantic morphology planning and control. We solve one source traversal and extract four contact-semantic primitives that describe coordination among 21 members. Physics-constrained projection adapts them to unseen step heights with the same contact topology. When every phase remains feasible, adaptation does not recompute the complete motion. If one phase violates the new physical constraints, only that phase is recomputed. A full-space QP then tracks the adapted motion and corrects member and wheel errors. For transfer from 0.10m to 0.075m, the method reduces objective-function evaluations by 63.7% relative to full recomputation. Contact-phase feasibility analysis covers step heights from 0.10 to 0.46m, or 1.08 to 4.97 wheel radii, with the upper value near the theoretical feasible boundary. The electric prototype traverses 2.11 wheel radii. The resulting low-dimensional representation stores task coordination in a hyper-redundant, load-bearing morphology and reuses it during locomotion.

0.30

Recompositional Robotics: Cross-Domain, Open-set, and Lifelong Modularity Beyond Morphology

cs.RO ·2026-09-29 ·Steven Swanbeck, Jonathan Salfity, Corrie Van Sice, Robert Blake Anderson, Mitch Pryor
published similarity 0.58
Abstract · 2026 IEEE/RSJ IROS Workshop on Reconfigurable Modular Robots

Research in modular robotics has produced capable approaches allowing a robot's morphology to change online, with recent efforts also developing approaches to decide which morphology to assume and automatically propagate that decision into the robot's motion planning and control. These approaches are powerful and increase adaptability in the field. However, an alternative objective is not to build robots whose structures can change, but robots whose fundamental capabilities can change, where capability is a joint function across several domains, including kino-dynamics, perception, compute, and high-level coordinating behaviors. A robot designed to be reconfigured across these domains has a greater capacity to alter its capability than one that can be reconfigured in a single domain. We refer to this cross-domain reconfigurability as integration span, and recognize a complementary measure of the resistance to reconfiguration, which we refer to as integration inertia. Current modular robots have reduced integration inertia in the structural domain while it remains high in the other domains that contribute to integration span. We assert that the systems that can provide the most utility through reconfiguration in practice are those maximizing span and minimizing inertia and call this general problem recompositional robotics: adaptation over a heterogeneous set of modules including hardware, software, compute, and behavior that abstracts each component by the interfaces it requires and provides such that they can be reasoned over holistically. We define the problem, ground it in two deployed systems and active research efforts, and pose open questions about the future of recompositional robotics.

0.28

Contact as a Decision Variable: Capability-Tradeoff Contact Selection for Legged Loco-Manipulation

cs.RO ·2026-09-24 ·Al Jaber Mahmud, Shuai Li, Xuan Wang
similarity 0.57
Abstract · 9 pages, 6 figures

In this paper, we study the joint selection of an environmental support contact and a whole-body configuration for a prescribed loco-manipulation task. A contact may provide greater physical support while restricting the motion required for the task. We formulate this problem through three capability measures: residual wrench, end-effector reach, and base mobility available after satisfying the task requirements, and we balance them against contact acquisition cost. Evaluating these capabilities for every candidate requires repeated whole-body optimizations. To reduce this computational cost, we propose Capability-Tradeoff Contact Selection (CTCS). CTCS screens candidates for contact and task feasibility, groups similar candidates within each surface, and predicts their capabilities from exact anchor evaluations using local sensitivity analysis. It checks these predictions through selective exact evaluations, ranks candidates by capability, and evaluates a shortlist exactly for final selection. We evaluate CTCS in simulations and hardware experiments using a Unitree Go2 quadruped with an AgileX NERO arm across $392$ task conditions with nine available support surfaces. Results show that CTCS outperforms ground-only and fixed-contact support, as it can select support surfaces that provide favorable capability trade-offs for the task. Compared with evaluating every candidate exactly, CTCS achieves approximately $3\times$ speedup while closely matching the resulting mean objective value.

0.56

Reconfiguration-Complete Motion Primitives with Constructive Planning for Deformable Planar Modular Robots

cs.RO ·2026-08-18 ·Jie Gu, Tingting Wang, Hongrun Gao, Yirun Sun, Zhihao Xia +2 more
theory similarity 0.57
Abstract · Jie Gu and Tingting Wang contributed equally to this work

The continuously deformable geometry of modular robots makes it difficult to define a fixed representation for reconfiguration planning and analysis. This letter introduces a square-cell abstraction that maps deformable rhombus modules to fixed-size grid cells while retaining physically interpretable local motions through two primitives, pivoting and shearing. Under this abstraction, we prove that every non-straight edge-connected configuration with $N \geq 7$ can be transformed to a fixed canonical staircase using only admissible primitive motions. Since these motions are reversible, any two configurations in this class are mutually reconfigurable. The proof is constructive and directly yields a staircase-canonicalization planner that transports removable boundary modules while preserving connectivity. As a practical enhancement, we further introduce a boundary-to-delivery lookahead selector that ranks admissible high level choices without affecting the completeness guarantee. Experiments demonstrate the constructive reconfiguration process and show that the selector substantially reduces planning time, while reference comparisons indicate lower planning times than the prior framework over the shared module counts.

0.24

WRAP: Fixtureless Wrench-aware Multi-Robot Assembly Planning

cs.RO ·2026-09-24 ·Valentin N. Hartmann, Huang Su, Yijiang Huang, Stelian Coros
benchmarkcode/data similarity 0.57
Abstract · 8 pages, 9 figures, 5 tables

Assembly using robots often requires specially designed fixtures, or relies on top-down only assembly strategies. Using multiple robots, we can avoid using fixtures and make robotic assembly more flexible. Planning assembly sequences for multiple robots is challenging due to the high number of possible task assignments and orders. In addition, we need to reason over forces that occur during the assembly process, e.g., to decide if multiple robots are required for support, or if external support such as a table should be used. We present Wrap, a multi-robot assembly planner for multi-part assemblies, given the inter-part ordering-dependencies, the part meshes, and their initial state. We formulate a linear program to reason about valid grasps for supporting the forces that occur during assembly. The search leverages the assembly sequence, and greedily finds a feasible solution per assembly step by computing a heuristic via a cheap backwards search, and using the heuristic in the more expensive forward search. We then solve the multi-robot, multi-goal motion planning problem, and for execution, we split the plan into contact-rich assembly skills, and free space motion. We benchmark the planner on a variety of multi-part assemblies, and apply the planner to groups of robots differing in size and kinematics. We validate the work both in a physics simulation, and in real. Videos and code are available at https://www.vhartmann.com/wrap.

0.33

Post-Grasp Kinematic Repair for Robotic Insertion via Object-in-Gripper Reorientation

cs.RO ·2026-10-06 ·Haegu Lee, Christoffer Sloth
similarity 0.56
Abstract

A stable grasp does not guarantee kinematically feasible robotic insertion because the object-in-gripper transform may force the robot towards singularities or joint limits along the prescribed insertion path. We study post-grasp kinematic feasibility repair through object-in-gripper reorientation. Given an achieved grasp and a fixed insertion path, we seek a small reorientation that restores kinematic feasibility. Sequential IK can miss such candidates by following an unfavorable joint-space path, while the nonsmooth feasibility landscape makes the search computationally expensive. We evaluate candidates using a branch-aware IK graph that maximizes the minimum feasibility margin over the discretized insertion path and use a learned task-conditioned prior to improve query ordering. The selected reorientation is executed through tactile-based extrinsic manipulation. In UR5e simulations, the planner without learned ranking reduces mean reorientation over successful trials by 51.5% compared with grid-based sequential IK. Adding learned ranking reduces this planner's mean planning time by an additional 51.1%. Real-robot experiments validate the complete pipeline.

0.19