CS Paper Radar

SHAFT: A Slack-Compensating, Helical-Buckling-Attenuating Flexible-Shaft Transmission for Lightweight Multi-DoF Manipulation

Tomoya Takahashi, Moses Gladson Selvamuthu, Richiro Tadakuma, Kazutoshi Tanaka

cs.RO ·submitted 2026-09-19 01:17 UTC · v1
published

Abstract

Lightweight and slim manipulators enable safe operation in human living environments. Proximal actuation using remote transmission mechanisms, such as wire-driven or Bowden cables, effectively reduces inertia and arm size by relocating motors near the base and transmitting torque to distal joints. Existing approaches either increase mass through additional components, such as pulleys for direction changes, or suffer from reduced transmission efficiency due to friction losses. Flexible shaft transmission avoids both mass increase and excessive friction losses, but faces increasing angular transmission error due to helical buckling caused by slack generated at joint bending. To address this problem, we propose SHAFT: a Slack-compensating, Helical-buckling-Attenuating Flexible- shaft Transmission mechanism. This mechanism compensates for slack through a proximal tensioner, improving the angular transmission error and efficiency of flexible shaft transmission without increasing the moving mass of the arm section. In a transmission path containing four 90-degree bends, the proposed mechanism demonstrated approximately 30% higher efficiency and approximately 65% lower angular transmission error compared to a flexible shaft transmission without a tensioner. Using this mechanism, we fabricated a 6-Degree-of-Freedom (DoF) arm with a 1-DoF gripper manipulator consisting of a rotary module housing motors with a tensioner, and a 280 g weight for the arm module. The proposed manipulator represents a novel remote actuation system for achieving lightweight construction with high efficiency, contributing to the acceleration of safe robot deployment in human environments.

Comment
9 pages, 14 figures, submitted as proceedings of IROS2026

Closest papers

Nearest neighbours by meaning across the whole index.

A Compact Robotic Finger with 2-DoF MCP Joint Embedding DoF-Selective Passive Continuously Variable Transmission for Wide Force-Speed Operating Range

cs.RO ·2026-09-01 ·JaeHyung Jang, Jee-Hwan Ryu
similarity 0.62
Abstract · 9 pages, 4 figures

This letter presents a compact two-degree-of-freedom (DoF) robotic finger with a flexion-selective passive continuously variable transmission (CVT) to achieve a wide force-speed operating range. Inspired by the functional differentiation of the human metacarpophalangeal (MCP) joint, the proposed mechanism realizes DoF-specific transmission differentiation by selectively assigning passive CVT to the flexion-extension DoF while preserving direct transmission for abduction-adduction. For a wide force-speed operating range, a force-responsive passive CVT is embedded in the flexion pathway, while direct transmission is preserved for the abduction-adduction pathway. To selectively realize transmission adaptation within a multi-DoF MCP mechanism, an output-side passive CVT employing a moving-pulley-inspired wire-routing structure is introduced. The resultant force generated by the wire tensions acting on the pulley that passively increases the flexion moment arm and transmission ratio according to the applied load without additional actuators, sensors, or control. Experimental results demonstrate a maximum output-force amplification of 4.19-fold and a mean amplification of 3.6-fold across the tested flexion angles ranging from 15 degrees to 75 degrees through moment-arm adaptation, thereby substantially expanding the achievable force-speed operating range. Furthermore, dexterous ball-rolling experiments verify that passive transmission adaptation can be achieved while preserving abduction-adduction functionality. These results demonstrate a scalable transmission design strategy for compact multi-DoF robotic hands.

0.23

MuJoCable: Reduced-Order Surface-Routed Cable Transmission for Tendon-Driven Robots

cs.RO cs.CE ·2026-09-09 ·Yi Zhang, Qi Shao, Yicong Lin, Muyuan Ma, Tao Sun +1 more
similarity 0.62
Abstract · 14 pages, 6 figures, 3 tables

Tendon transmissions reduce distal inertia and add compliance, yet routing, slack, and friction govern motion and force transfer. Mainstream rigid-body robotics simulators such as MuJoCo do not jointly resolve moving noncircular contact, unilateral tension, and segment friction. We present MuJoCable, which adds a reduced-order, configuration-dependent cable transmission to MuJoCo. Its routing algorithm jointly optimizes an ordered path across moving analytic and mesh surfaces. A unilateral axial law, directional Capstan propagation, and nodal virtual work map this path to segment tensions and body forces. The warm-started engine plugin applies these forces during simulation and exposes route and load states for design. Pulley benchmarks recover analytical transmission relations with a Capstan-ratio error below 0.5%. On the underactuated 18-joint SpiRobs, MuJoCable reveals friction-driven load growth and proximal redistribution of joint rotation that the native tendon does not represent. Hardware tests on SpiRobs and a tendon-route-coupled finger reproduce observed motion sequences. By making physical threading executable, MuJoCable brings transmission sources of the simulation-to-reality gap into route, cable, and actuator design before fabrication.

0.26

Design of a Fully Actuated 4-DOF Robotic Finger With Joint-Specific Hybrid Remote Actuation

cs.RO ·2026-10-07 ·Hyojae Kang, Hyun-mok Jung, Joonho Lee, Dongil Park, Hyunmin Do +2 more
similarity 0.61
Abstract · 10 pages, 10 figures. This manuscript has been submitted for possible publication

This paper presents a fully actuated 4-DOF robotic finger using a joint-specific hybrid remote-actuation architecture. The metacarpophalangeal (MCP) joint is driven by two coordinated rigid-link transmission sets, whereas the proximal interphalangeal (PIP) and distal interphalangeal (DIP) joints are independently actuated by closed-loop wire transmissions incorporating circular rolling-contact joints (RCJs). A larger transmission radius is used at the PIP joint than at the DIP joint. The RCJ wire geometry maintains the total wire-loop length during joint rotation, and the DIP wire routing is designed so that PIP motion does not affect its differential actuation for a fixed MCP configuration. The distal wire transmission, MCP linkage, and fingertip kinematics are analytically modeled. In experiments, the transmission behavior was quantitatively evaluated from the ball-screw displacements measured using ArUco-marker tracking. MCP actuation produced measurable displacements of the PIP and DIP transmission units, whereas isolated PIP and DIP actuation with the MCP fixed supported the intended mechanical decoupling between the distal transmissions. The mean peak fingertip forces under isolated MCP, PIP, and DIP actuation were 21.28 N, 9.22 N, and 5.75 N, respectively. The resulting finger postures were also examined using objects of different geometries and sizes.

0.37

A Direct Rigid Transmission 2-DoF Wrist Extension for Tendon-Driven Hand

cs.RO ·2026-09-19 ·Yujie Pang, Sadman Sakib, Mohammad Abdullah Al Faruque
published similarity 0.59
Abstract · Accepted at "IROS 2026 Sensors and Actuators for Dexterous Manipulation Workshop"

Dexterous manipulation in confined spaces requires local control of hand orientation. Without a wrist, a dexterous hand must obtain this local orientation through coordinated motion of the robot arm, often involving several joints and a more complex end-effector path. We present CRAFT-Wrist, a concentric 2-DoF wrist extension that mounts between a robot arm and the CRAFT Hand without modifying the hand. Two XC430-T240BB-T servos drive sideways and front-back rotation through short rigid transmissions. Our initial hardware prototype actuates both axes under load, achieving a demonstrated workspace of $\pm20^{\circ}$ in radial--ulnar deviation (left--right) and a front-back range of $+80^{\circ}$ in flexion and $-18^{\circ}$ in extension. We characterize the resulting finger-motor loading across several wrist postures and demonstrate how the wrist supplies local orientation in grasping, nail hammering, and blackboard wiping. Demonstrations and assembly instructions are available at https://craft-wrist.github.io/.

0.60

Design and Characterization of a Variable-Length Continuum Mechanism with Force Locking

cs.RO ·2026-09-25 ·Katelyn King, Veronica Fish, Allison M. Okamura
hot direction similarity 0.59
Abstract · 7 pages, 9 figures. Submitted to ICRA 2027. Ancillary files contain a supplementary video

The utility of flexible continuum mechanisms for dexterous navigation is often impaired by their low stiffness, making them ineffective at manipulation in high-force scenarios. To address this challenge, we propose a novel continuum mechanism that achieves both flexible and rigid behavior by antagonistic extension and contraction of a rod-driven continuum helical structure. The helical design combines variable-length capacity with force locking for workspace and stiffness enhancement. In this article, we present the detailed design of the proposed mechanism and characterize its performance through experiments that quantify bending and stiffness. The results demonstrate 180 degree bending range of motion with an average distal positioning error of <10%. Further tests demonstrate that force locking directly improves axial stiffness and thus indirectly increases bending stiffness anisotropically, with maximum bending stiffness along load paths with a large axial component. Tensioning the driving rods provides additional stiffness tunability in the force-locked state, where increasing rod tension proportionally increases bending stiffness with a dimensionless gain of 0.56.

0.37

Flexibility-Aware Robotic Manipulation: Deformation Estimation, Kinematics, and Control via Distributed Inertial Measurement

cs.RO ·2026-10-30 ·Amir Hossein Barjini, Sadeq Yaqubi, Pauli Mustalahti, Jouni Mattila
similarity 0.58
Abstract

Flexible robot links challenge the rigid-body assumption, making joint measurements alone insufficient for accurate manipulation. This paper introduces a flexibility-aware manipulation framework that connects structural dynamics directly to sensing, kinematics, and control. Instead of prescribing a dense inertial measurement unit (IMU) network, the dominant vibration modes of each flexible link are first identified from response-convergence and excitation-bandwidth criteria. Under a full-rank modal observability condition, $m$ retained modes require only $m$ independent slope measurements and one reference IMU, defining the minimum observable IMU configuration. The resulting measurements are used to reconstruct the continuous link deformation, which is then incorporated into flexibility-aware forward kinematics and a deformation-informed partial differential equation-based controller. Experiments on hydraulic single- and double-link manipulators evaluate the framework. On the long-reach double-link platform, the proposed kinematics achieves end-effector root mean square errors of $0.0107$~m, $0.0194$~m, and $0.0102$~rad while using fewer sensors than the piecewise-rigid method. Closed-loop reaching experiments further demonstrate real-time integration of IMU-estimated joint states and reconstructed deformation into the proposed controller. The results show that dominant modal information can determine sensing requirements and enable real-time flexibility-aware robotic manipulation.

0.34

Cosserat Modeling of Trimmed Helicoid Soft Arms with a Separated-Section Constitutive Law

cs.RO ·2026-09-21 ·Zhihang Qin, Linxin Hou, Zeyu Zhong, Yuchen Sun, Wenci Xin +8 more
similarity 0.57
Abstract

Cosserat rod models for soft robots usually construct sectional stiffness by summing material properties over a common cross-section. This assumption becomes inaccurate for trimmed helicoid arms, where load-bearing helix domains are separated and connected only through sparse fused crossings. This paper formulates a separated-section constitutive law that evaluates each helix domain in its local frame and pulls its constitutive response back to the backbone, yielding an effective backbone stiffness. Sparse-fusion mechanics captures the additional compliance caused by relative motion between neighboring domains and determines channel-wise reduction profiles $η_c(s/L)$ for bending, torsion, and extension. The resulting effective sectional stiffness is strongly anisotropic: bending and extension are reduced by about one order of magnitude, whereas torsion remains close to the effective backbone stiffness. The resulting sectional law is embedded in a geometrically exact dynamic Cosserat model with GVS discretization and routed-tendon actuation. Across 103 measured configurations, the three datasets give pooled normalized position errors of $7.7 \ \%$, $6.7 \ \%$, and $7.8 \ \%$, while each full-arm solve requires approximately $0.3 \ \mathrm{s}$ on one CPU core (Intel Xeon, Cascade Lake, $2.8 \mathrm{GHz}$), enabling rapid model-based planning, state and load estimation, and morphology--control co-design for architected soft robots.

0.38

Design and Validation of an Antagonistic Tendon-Driven Dexterous Robotic Hand with Bidirectional Operation

cs.RO ·2026-09-28 ·Chunghyeon Lee, Hyukjun Kwon, Sungeon Kim, Saehyun Moon, Seokhwan Jeong
similarity 0.56
Abstract

Dexterous robotic hands typically reproduce human hand morphology but inherit its one-sided grasping workspace, requiring wrist or arm reorientation to grasp from the opposite side. Existing reversible hands generally rely on non-anthropomorphic, soft, or task-specific finger arrangements, whereas conventional five-digit anthropomorphic hands remain designed primarily for palmar-side grasping. This paper presents an anthropomorphic, human-scale (200 mm length), lightweight (220 g), 3D-printed, 17-DoF robotic hand built on a bidirectional antagonistic tendon-routing mechanism, in which flexion/extension (except the coupled joint) and abduction/adduction at joints are actively driven without passive return springs. The proposed routing mechanism allows all degrees of freedom to cross their neutral configuration and form grasp closures on either the palmar or dorsal side. Experimental evaluation demonstrates an average motor-to-joint transmission error of 3.0%, an average joint transmission bandwidth of 13.2 Hz, a maximum fingertip force of 29 N, and a positioning repeatability up to 0.15 mm. The hand further achieves a Kapandji score of 8, successfully performs all 33 GRASP Taxonomy grasp types, and performs palmar- and dorsal-side grasping tasks, validating bidirectional operation in a compact, human-scale platform.

0.35