CS Paper Radar

Cosserat Modeling of Trimmed Helicoid Soft Arms with a Separated-Section Constitutive Law

Zhihang Qin, Linxin Hou, Zeyu Zhong, Yuchen Sun, Wenci Xin, Yueheng Zhang, Ji Qi, Jie Wang, Peiyi Wang, Muhammad Sunny Nazeer, Yu Jun Tan, Federico Renda, Cecilia Laschi

cs.RO ·submitted 2026-09-21 18:13 UTC · v2

Abstract

Cosserat rod models for soft robots usually construct sectional stiffness by summing material properties over a common cross-section. This assumption becomes inaccurate for trimmed helicoid arms, where load-bearing helix domains are separated and connected only through sparse fused crossings. This paper formulates a separated-section constitutive law that evaluates each helix domain in its local frame and pulls its constitutive response back to the backbone, yielding an effective backbone stiffness. Sparse-fusion mechanics captures the additional compliance caused by relative motion between neighboring domains and determines channel-wise reduction profiles $η_c(s/L)$ for bending, torsion, and extension. The resulting effective sectional stiffness is strongly anisotropic: bending and extension are reduced by about one order of magnitude, whereas torsion remains close to the effective backbone stiffness. The resulting sectional law is embedded in a geometrically exact dynamic Cosserat model with GVS discretization and routed-tendon actuation. Across 103 measured configurations, the three datasets give pooled normalized position errors of $7.7 \ \%$, $6.7 \ \%$, and $7.8 \ \%$, while each full-arm solve requires approximately $0.3 \ \mathrm{s}$ on one CPU core (Intel Xeon, Cascade Lake, $2.8 \mathrm{GHz}$), enabling rapid model-based planning, state and load estimation, and morphology--control co-design for architected soft robots.

Closest papers

Nearest neighbours by meaning across the whole index.

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.64
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Reduced Cartesian Kinetostatics for Tendon-Driven Continuum Robots: Residual-Stabilized Full-Shape Propagation

cs.RO ·2026-09-24 ·Ke Wu, Fangju Yang, Xiaohui Zhang, Zhengqiang Zhang, Jingang Yi +1 more
hot direction similarity 0.62
Abstract

Many planning and control tasks for tendon-driven continuum robots (TDCRs) require the complete Cartesian backbone geometry. We present a reduced Cartesian framework for planar, axially compressible TDCRs that propagates equilibrium configurations along prescribed tendon-force and tendon-displacement trajectories. The backbone is represented by two global position fields. Following exact variation, a Taylor-Galerkin reduction condenses prescribed spatial properties and distributed loads into offline moment vectors, yielding analytic reduced residuals and Jacobians without online spatial quadrature or numerical differentiation. Analytical differentiation and residual correction yield first-order rate systems requiring one fixed-dimensional linear solve per rate evaluation after initial equilibrium alignment on a regular branch. Across four simulated cases covering variable tendon routing, nonuniform geometry, axial compression, and their combined effects, the propagated Cartesian shapes and distributed strains closely match pointwise geometrically variable-strain (GVS) equilibrium solutions. Residual correction suppresses propagation drift across the tested step sizes while adding only about 0.98% to the mean update time of uncorrected Euler. The proposed method requires 0.508 ms per update on average, approximately 11 times faster than pointwise GVS solves. Displacement-driven experiments yield a maximum normalized mean backbone position error of 1.02% and a maximum end-effector position error of 0.28%. These results support efficient and accurate Cartesian full-shape prediction along prescribed actuation paths.

0.30

Closed-Form Cartesian Forward Kinetostatics for Spatial Multi-Segment Tendon-Driven Continuum Robots

cs.RO ·2026-09-29 ·Ke Wu, Fangju Yang, Xiaohui Zhang, Junda He, Guanjun Bao +2 more
benchmark similarity 0.61
Abstract

Forward kinetostatics of spatial tendon-driven continuum robots typically requires a nonlinear equilibrium solve for each actuation input. This paper develops a force-to-Cartesian-configuration model with a closed-form solution in quadratures for spatial multi-segment robots under tendon actuation. The Cartesian backbone centerline and accumulated material twist serve as generalized coordinates, from which the strain measures and tendon geometry are derived. Variational equilibrium yields explicit axial and bending relations and establishes zero equilibrium material twist within the proposed model for admissible longitudinal non-helical routing. The solution is propagated segment by segment without an iterative equilibrium solve, while retaining axial deformation, spatially varying axial and bending stiffnesses and tendon-routing diameter, and segment-dependent tendon participation. Numerical comparisons with a full-strain geometric variable-strain model (GVS) yield maximum length-normalized tip-position discrepancies of 8.91 x 10^-6 and 1.01 x 10^-5 for the single- and three-segment robots, respectively. Mean evaluation times of 1.52 μs and 2.94 μs, with corresponding speedups of approximately 1864x and 3348x over the baseline, demonstrate the computational advantage of the explicit force-to-configuration mapping in the reported benchmark.

0.14

Design and Characterization of a Variable-Length Continuum Mechanism with Force Locking

cs.RO ·2026-09-25 ·Katelyn King, Veronica Fish, Allison M. Okamura
hot direction similarity 0.59
Abstract · 7 pages, 9 figures. Submitted to ICRA 2027. Ancillary files contain a supplementary video

The utility of flexible continuum mechanisms for dexterous navigation is often impaired by their low stiffness, making them ineffective at manipulation in high-force scenarios. To address this challenge, we propose a novel continuum mechanism that achieves both flexible and rigid behavior by antagonistic extension and contraction of a rod-driven continuum helical structure. The helical design combines variable-length capacity with force locking for workspace and stiffness enhancement. In this article, we present the detailed design of the proposed mechanism and characterize its performance through experiments that quantify bending and stiffness. The results demonstrate 180 degree bending range of motion with an average distal positioning error of <10%. Further tests demonstrate that force locking directly improves axial stiffness and thus indirectly increases bending stiffness anisotropically, with maximum bending stiffness along load paths with a large axial component. Tensioning the driving rods provides additional stiffness tunability in the force-locked state, where increasing rod tension proportionally increases bending stiffness with a dimensionless gain of 0.56.

0.37

SHAFT: A Slack-Compensating, Helical-Buckling-Attenuating Flexible-Shaft Transmission for Lightweight Multi-DoF Manipulation

cs.RO ·2026-09-19 ·Tomoya Takahashi, Moses Gladson Selvamuthu, Richiro Tadakuma, Kazutoshi Tanaka
published similarity 0.57
Abstract · 9 pages, 14 figures, submitted as proceedings of IROS2026

Lightweight and slim manipulators enable safe operation in human living environments. Proximal actuation using remote transmission mechanisms, such as wire-driven or Bowden cables, effectively reduces inertia and arm size by relocating motors near the base and transmitting torque to distal joints. Existing approaches either increase mass through additional components, such as pulleys for direction changes, or suffer from reduced transmission efficiency due to friction losses. Flexible shaft transmission avoids both mass increase and excessive friction losses, but faces increasing angular transmission error due to helical buckling caused by slack generated at joint bending. To address this problem, we propose SHAFT: a Slack-compensating, Helical-buckling-Attenuating Flexible- shaft Transmission mechanism. This mechanism compensates for slack through a proximal tensioner, improving the angular transmission error and efficiency of flexible shaft transmission without increasing the moving mass of the arm section. In a transmission path containing four 90-degree bends, the proposed mechanism demonstrated approximately 30% higher efficiency and approximately 65% lower angular transmission error compared to a flexible shaft transmission without a tensioner. Using this mechanism, we fabricated a 6-Degree-of-Freedom (DoF) arm with a 1-DoF gripper manipulator consisting of a rotary module housing motors with a tensioner, and a 280 g weight for the arm module. The proposed manipulator represents a novel remote actuation system for achieving lightweight construction with high efficiency, contributing to the acceleration of safe robot deployment in human environments.

0.42

An Open MuJoCo Simulation Framework for a Quadrotor Carrying a Tendon-Driven Soft Continuum Arm

cs.RO eess.SY ·2026-10-11 ·Haitham El-Hussieny
code/data similarity 0.57
Abstract

Combining aerial robots with soft continuum manipulators promises safe, compliant interaction with the environment, but the coupled dynamics of a free-flying base and a highly deformable, underactuated arm are difficult to study without a suitable simulator. This paper describes an open-source simulation framework, built on the MuJoCo physics engine, for a quadrotor that carries a tendon-driven soft continuum arm underneath its body. The arm is modelled as a pseudo-rigid-body chain of twelve segments joined by pairs of orthogonal compliant hinges. Three tendons, spaced \SI{120}{\degree} apart and routed through every segment, bend it in any direction. A geometric tracking controller on $SE(3)$ flies the vehicle; its rotor allocation matrix is generated directly from the model description. A closed-form tendon-tension allocation keeps every tension within its limits and gives the same bending moment in every direction. We report the full set of modelling choices and parameters, and we evaluate the framework in four simulated scenarios: a \SI{36}{\second} mission with a figure-eight and a tendon-driven tip sweep, an attitude-gain study, a quasi-static characterization of the bending workspace, and an impulsive disturbance applied to the arm tip. With the nominal gains the vehicle tracks the mission with \SI{3.1}{\centi\meter} RMS position error while the arm tip swings up to \SI{37}{\centi\meter} from the body axis. The gain study shows that a low-bandwidth attitude loop lets the arm excite sustained oscillations. The simulation runs about $15\times$ faster than real time on a laptop CPU. All models, controllers and scripts that reproduce the figures are released.

0.25

Active 3D weaves for load-bearing and damage-resilient locomotion

cs.RO cond-mat.mtrl-scicond-mat.soft ·2026-09-26 ·Guowei Wayne Tu, Evgueni T. Filipov
similarity 0.57
Abstract

The craft of weaving, where different materials are interlaced, has tremendous potential for creating active and functional systems for use in soft robots, prosthetics, wearables, exoskeletons, and more. These textile-like systems are flexible and safe for human-machine interaction; however, this inherent flexibility limits their ability to carry loads, which is essential for many robotic functions. In this work, we introduce a general framework for integrating active materials into three-dimensional (3D) woven shells to create robotic structures that combine high axial stiffness for load bearing, low bending stiffness for efficient actuation, and system-level resilience for damage tolerance. These woven robots can be modularly assembled from 'woven corners', a fundamental unit of 3D woven structures. We use eigenvalue calculations to identify load bearing and actuation mechanisms of the 3D woven structures, and use that information to make five different robots capable of locomotion. We demonstrate that these 3D woven robots can locomote carrying loads 70 times their self-weight, and can maintain repeatable performance even after being subjected to extreme compression. This work is a pathway toward the design, manufacturing, and simulation of future 3D woven robotic systems where load bearing, high stiffness, active functional deformation, locomotion, and system-level resilience are all needed.

0.22

Actuation and Control of Passive Tendon-Driven Soft Extensions Through Rigid Manipulator Motion

cs.RO ·2026-11-11 ·Ignacio Cuiral-Zueco, Gonzalo López-Nicolás, Youcef Mezouar
theorycode/data similarity 0.56
Abstract · 16 pages, 12 figures. Soon to be submitted to the IEEE Transactions on Robotics. Code: https://github.com/nachocz/passive_soft_extension_con…

Industrial manipulators offer reach and precision but can damage nearby structures in confined spaces. Soft robots provide compliant contact but typically have limited reach. Rigid-soft systems combine their advantages, although they often require dedicated actuation and control hardware. We propose actuating a passive tendon-driven soft extension through manipulator joint motion. As the robot moves, the exterior spans of tendons anchored to upstream links change, altering tendon tension and deforming the extension. Inspection through narrow apertures, for example, constrains the motion of the end effector (EE). We develop a controller that regulates the soft tip while preserving such EE constraints. A differential model separates rigid transport from soft deformation, combining analytic arm and tendon kinematics with a locally identified span-to-deformation map. We also derive a local upper bound on the number of independent deformation directions transmitted by the tendons under the EE constraint, and conditions for the exponential convergence of the tip error. A quadratic program with control barrier functions imposes obstacle clearance, fulcrum limits, and model-validity conditions. Simulations and real experiments show tip and shape regulation under free, position-constrained, and fulcrum-constrained EE motion.

0.42