CS Paper Radar

Closed-Form Cartesian Forward Kinetostatics for Spatial Multi-Segment Tendon-Driven Continuum Robots

Ke Wu, Fangju Yang, Xiaohui Zhang, Junda He, Guanjun Bao, Jingang Yi, Jian S. Dai

cs.RO ·submitted 2026-09-29 01:50 UTC · v1
benchmark

Abstract

Forward kinetostatics of spatial tendon-driven continuum robots typically requires a nonlinear equilibrium solve for each actuation input. This paper develops a force-to-Cartesian-configuration model with a closed-form solution in quadratures for spatial multi-segment robots under tendon actuation. The Cartesian backbone centerline and accumulated material twist serve as generalized coordinates, from which the strain measures and tendon geometry are derived. Variational equilibrium yields explicit axial and bending relations and establishes zero equilibrium material twist within the proposed model for admissible longitudinal non-helical routing. The solution is propagated segment by segment without an iterative equilibrium solve, while retaining axial deformation, spatially varying axial and bending stiffnesses and tendon-routing diameter, and segment-dependent tendon participation. Numerical comparisons with a full-strain geometric variable-strain model (GVS) yield maximum length-normalized tip-position discrepancies of 8.91 x 10^-6 and 1.01 x 10^-5 for the single- and three-segment robots, respectively. Mean evaluation times of 1.52 μs and 2.94 μs, with corresponding speedups of approximately 1864x and 3348x over the baseline, demonstrate the computational advantage of the explicit force-to-configuration mapping in the reported benchmark.

Closest papers

Nearest neighbours by meaning across the whole index.

Reduced Cartesian Kinetostatics for Tendon-Driven Continuum Robots: Residual-Stabilized Full-Shape Propagation

cs.RO ·2026-09-24 ·Ke Wu, Fangju Yang, Xiaohui Zhang, Zhengqiang Zhang, Jingang Yi +1 more
hot direction similarity 0.74
Abstract

Many planning and control tasks for tendon-driven continuum robots (TDCRs) require the complete Cartesian backbone geometry. We present a reduced Cartesian framework for planar, axially compressible TDCRs that propagates equilibrium configurations along prescribed tendon-force and tendon-displacement trajectories. The backbone is represented by two global position fields. Following exact variation, a Taylor-Galerkin reduction condenses prescribed spatial properties and distributed loads into offline moment vectors, yielding analytic reduced residuals and Jacobians without online spatial quadrature or numerical differentiation. Analytical differentiation and residual correction yield first-order rate systems requiring one fixed-dimensional linear solve per rate evaluation after initial equilibrium alignment on a regular branch. Across four simulated cases covering variable tendon routing, nonuniform geometry, axial compression, and their combined effects, the propagated Cartesian shapes and distributed strains closely match pointwise geometrically variable-strain (GVS) equilibrium solutions. Residual correction suppresses propagation drift across the tested step sizes while adding only about 0.98% to the mean update time of uncorrected Euler. The proposed method requires 0.508 ms per update on average, approximately 11 times faster than pointwise GVS solves. Displacement-driven experiments yield a maximum normalized mean backbone position error of 1.02% and a maximum end-effector position error of 0.28%. These results support efficient and accurate Cartesian full-shape prediction along prescribed actuation paths.

0.30

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.73
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Real-Time Whole-Body Safe Motion Generation for Multi-Segment Tendon-Driven Continuum Robots

cs.RO ·2026-09-22 ·Fangju Yang, Siyi Ma, Tonghao Guan, Tingcong Liu, Hang Yang +3 more
hot direction similarity 0.70
Abstract

Real-time motion generation for tendon-driven continuum robots requires accurate modeling of nonuniform bending and whole-body collision avoidance. This paper presents a unified actuation-space framework for planar multi-segment tendon-driven continuum robots. An energy-based variable-curvature model captures spatially varying tendon spacing and bending stiffness and provides analytical Jacobians for differential inverse kinematics and safety monitoring. A multipoint CBF-QP enforces backbone clearance under obstacle motion and actuation-velocity bounds, while its decision dimension depends only on the number of independently actuated segments. The model closely agrees with GVS references, with a maximum curvature error of $5.223 \times 10^{-2}\,\mathrm{m}^{-1}$. Over 100 MuJoCo trials, the proposed method achieves collision-free success rates of 96% and 100% in static and dynamic scenarios, respectively, compared with approximately 60% and 80% without CBF constraints. Hole-traversal tests further demonstrate safe motion in constrained environments. With 600 backbone monitoring points, the mean control-step time is 6.66 ms, demonstrating real-time whole-body safe motion generation.

0.29

Design and Characterization of a Variable-Length Continuum Mechanism with Force Locking

cs.RO ·2026-09-25 ·Katelyn King, Veronica Fish, Allison M. Okamura
hot direction similarity 0.69
Abstract · 7 pages, 9 figures. Submitted to ICRA 2027. Ancillary files contain a supplementary video

The utility of flexible continuum mechanisms for dexterous navigation is often impaired by their low stiffness, making them ineffective at manipulation in high-force scenarios. To address this challenge, we propose a novel continuum mechanism that achieves both flexible and rigid behavior by antagonistic extension and contraction of a rod-driven continuum helical structure. The helical design combines variable-length capacity with force locking for workspace and stiffness enhancement. In this article, we present the detailed design of the proposed mechanism and characterize its performance through experiments that quantify bending and stiffness. The results demonstrate 180 degree bending range of motion with an average distal positioning error of <10%. Further tests demonstrate that force locking directly improves axial stiffness and thus indirectly increases bending stiffness anisotropically, with maximum bending stiffness along load paths with a large axial component. Tensioning the driving rods provides additional stiffness tunability in the force-locked state, where increasing rod tension proportionally increases bending stiffness with a dimensionless gain of 0.56.

0.37

Rotate Disks to Reach Farther: Design and Modeling of a Novel Reconfigurable Tendon Driven Manipulator

cs.RO ·2026-08-16 ·Sabyasachi Dash, Yangkun Liu, Will Hunter, John Golden, Girish Krishnan
similarity 0.63
Abstract

Rerouting the tendon path in tendon driven continuum manipulators (TDCMs) enables a broad range of deformation modes. This work presents a Reconfigurable TDCM design which allows independent rotation of intermediate spacer disks, thereby locally rerouting the tendon and achieving non-trivial backbone spatial deformations. Two such designs, (a) Manual Disk Locked (MDL) and (b) Continuous Disk Rotor (CDR) manipulators are presented to achieve disk rotations before and during operation, respectively. A predictive static model based on the piecewise constant strain (PCS) assumption is developed within a potential energy minimization framework, incorporating (a) disk rotations, (b) discrete tendon paths between disk segments, (c) rigid thickness of spacer disks, and (d) elasticity of the tendons. The model is validated against experimental results, demonstrating an average tip error of $1.2\%$ of the manipulator's total length for parallel tendon routing and around $3\%$ for the case when multiple disks are rotated. The computation time is an order of magnitude lower than the state of the art Cosserat rod solver.

0.04

Cosserat Modeling of Trimmed Helicoid Soft Arms with a Separated-Section Constitutive Law

cs.RO ·2026-09-21 ·Zhihang Qin, Linxin Hou, Zeyu Zhong, Yuchen Sun, Wenci Xin +8 more
similarity 0.61
Abstract

Cosserat rod models for soft robots usually construct sectional stiffness by summing material properties over a common cross-section. This assumption becomes inaccurate for trimmed helicoid arms, where load-bearing helix domains are separated and connected only through sparse fused crossings. This paper formulates a separated-section constitutive law that evaluates each helix domain in its local frame and pulls its constitutive response back to the backbone, yielding an effective backbone stiffness. Sparse-fusion mechanics captures the additional compliance caused by relative motion between neighboring domains and determines channel-wise reduction profiles $η_c(s/L)$ for bending, torsion, and extension. The resulting effective sectional stiffness is strongly anisotropic: bending and extension are reduced by about one order of magnitude, whereas torsion remains close to the effective backbone stiffness. The resulting sectional law is embedded in a geometrically exact dynamic Cosserat model with GVS discretization and routed-tendon actuation. Across 103 measured configurations, the three datasets give pooled normalized position errors of $7.7 \ \%$, $6.7 \ \%$, and $7.8 \ \%$, while each full-arm solve requires approximately $0.3 \ \mathrm{s}$ on one CPU core (Intel Xeon, Cascade Lake, $2.8 \mathrm{GHz}$), enabling rapid model-based planning, state and load estimation, and morphology--control co-design for architected soft robots.

0.38

Modeling the Frictional Contact of Continuum Robots with Environments through Linear Complementarity Problem

cs.RO ·2026-11-13 ·Jia Shen, Junhyoung Ha, Yue Chen
published similarity 0.61
Abstract · Accepted for publication in the International Journal of Robotics Research (IJRR). 21 pages, 18 figures

Accurate friction modeling in continuum robots is essential for precise motion control and path planning. However, current approaches make predictions only for the mechanism's internal friction that is limited by the boundary forces of the Coulomb friction cone, which fail to characterize the static friction and motion hysteresis. In this paper, we propose a novel friction model based on complementarity constraints under the Coulomb friction assumption. This model predicts various friction effects caused by environmental interactions, including both static and sliding frictions and hysteresis behavior, as well as the corresponding robot deformation induced by these interactions, which are crucial for the practical motion planning and control of continuum robots. Additionally, real-time implementation of this model can be achieved, meeting the demand for computational efficiency in robotic applications. Experimental validations demonstrated that this model is able to reduce the maximum tip position error from 45.4 mm in the frictionless model to 5.85 mm in our friction-included model with a 287.9 mm-long tendon-driven continuum robot.

0.33

Estimation and Control of Tensegrity Manipulator Kinematics based on Strut Inclination Angles

cs.RO ·2026-09-21 ·Tufail Ahmad Bhat, Shuhei Ikemoto
top venue similarity 0.60
Abstract

Unlike conventional rigid-link robots defined by discrete joints, continuum robots pose a fundamental challenge for expressing their complex continuous bending configurations for closed-loop control. Several modelling approaches have been proposed for conventional continuum robots, but tensegrity-based continuum robots remain largely open. Moreover, many of these approaches assume a continuous elastic backbone and are therefore not directly applicable to tensegrity manipulators, whose bodies are networks of rigid struts and tensioned cables. This work presents a reduced-order model for shape and posture control of a tensegrity-based continuum manipulator. The manipulator is modelled as a serially connected parallel-link mechanism. The proposed method is formulated as an optimization problem that uses geometric constraints of the tensegrity structure together with information from the Inertial Measurement Unit (IMU) sensors embedded in the strut elements. To the best of our knowledge, this work presents the first experimental demonstration of a real-time IMU-based shape estimation method on a full-scale tensegrity manipulator and demonstrates posture control using a simple Proportional-Integral (PI) controller. The results show that the proposed method can estimate the shape of both single-module tensegrity structures and multi-module tensegrity manipulators from arbitrary static configurations and achieve desired postures.

0.48