CS Paper Radar

Rotate Disks to Reach Farther: Design and Modeling of a Novel Reconfigurable Tendon Driven Manipulator

Sabyasachi Dash, Yangkun Liu, Will Hunter, John Golden, Girish Krishnan

cs.RO ·submitted 2026-08-16 22:06 UTC · v2

Abstract

Rerouting the tendon path in tendon driven continuum manipulators (TDCMs) enables a broad range of deformation modes. This work presents a Reconfigurable TDCM design which allows independent rotation of intermediate spacer disks, thereby locally rerouting the tendon and achieving non-trivial backbone spatial deformations. Two such designs, (a) Manual Disk Locked (MDL) and (b) Continuous Disk Rotor (CDR) manipulators are presented to achieve disk rotations before and during operation, respectively. A predictive static model based on the piecewise constant strain (PCS) assumption is developed within a potential energy minimization framework, incorporating (a) disk rotations, (b) discrete tendon paths between disk segments, (c) rigid thickness of spacer disks, and (d) elasticity of the tendons. The model is validated against experimental results, demonstrating an average tip error of $1.2\%$ of the manipulator's total length for parallel tendon routing and around $3\%$ for the case when multiple disks are rotated. The computation time is an order of magnitude lower than the state of the art Cosserat rod solver.

Closest papers

Nearest neighbours by meaning across the whole index.

Closed-Form Cartesian Forward Kinetostatics for Spatial Multi-Segment Tendon-Driven Continuum Robots

cs.RO ·2026-09-29 ·Ke Wu, Fangju Yang, Xiaohui Zhang, Junda He, Guanjun Bao +2 more
benchmark similarity 0.63
Abstract

Forward kinetostatics of spatial tendon-driven continuum robots typically requires a nonlinear equilibrium solve for each actuation input. This paper develops a force-to-Cartesian-configuration model with a closed-form solution in quadratures for spatial multi-segment robots under tendon actuation. The Cartesian backbone centerline and accumulated material twist serve as generalized coordinates, from which the strain measures and tendon geometry are derived. Variational equilibrium yields explicit axial and bending relations and establishes zero equilibrium material twist within the proposed model for admissible longitudinal non-helical routing. The solution is propagated segment by segment without an iterative equilibrium solve, while retaining axial deformation, spatially varying axial and bending stiffnesses and tendon-routing diameter, and segment-dependent tendon participation. Numerical comparisons with a full-strain geometric variable-strain model (GVS) yield maximum length-normalized tip-position discrepancies of 8.91 x 10^-6 and 1.01 x 10^-5 for the single- and three-segment robots, respectively. Mean evaluation times of 1.52 μs and 2.94 μs, with corresponding speedups of approximately 1864x and 3348x over the baseline, demonstrate the computational advantage of the explicit force-to-configuration mapping in the reported benchmark.

0.14

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.61
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Actuation and Control of Passive Tendon-Driven Soft Extensions Through Rigid Manipulator Motion

cs.RO ·2026-11-11 ·Ignacio Cuiral-Zueco, Gonzalo López-Nicolás, Youcef Mezouar
theorycode/data similarity 0.61
Abstract · 16 pages, 12 figures. Soon to be submitted to the IEEE Transactions on Robotics. Code: https://github.com/nachocz/passive_soft_extension_con…

Industrial manipulators offer reach and precision but can damage nearby structures in confined spaces. Soft robots provide compliant contact but typically have limited reach. Rigid-soft systems combine their advantages, although they often require dedicated actuation and control hardware. We propose actuating a passive tendon-driven soft extension through manipulator joint motion. As the robot moves, the exterior spans of tendons anchored to upstream links change, altering tendon tension and deforming the extension. Inspection through narrow apertures, for example, constrains the motion of the end effector (EE). We develop a controller that regulates the soft tip while preserving such EE constraints. A differential model separates rigid transport from soft deformation, combining analytic arm and tendon kinematics with a locally identified span-to-deformation map. We also derive a local upper bound on the number of independent deformation directions transmitted by the tendons under the EE constraint, and conditions for the exponential convergence of the tip error. A quadratic program with control barrier functions imposes obstacle clearance, fulcrum limits, and model-validity conditions. Simulations and real experiments show tip and shape regulation under free, position-constrained, and fulcrum-constrained EE motion.

0.54

Reduced Cartesian Kinetostatics for Tendon-Driven Continuum Robots: Residual-Stabilized Full-Shape Propagation

cs.RO ·2026-09-24 ·Ke Wu, Fangju Yang, Xiaohui Zhang, Zhengqiang Zhang, Jingang Yi +1 more
hot direction similarity 0.61
Abstract

Many planning and control tasks for tendon-driven continuum robots (TDCRs) require the complete Cartesian backbone geometry. We present a reduced Cartesian framework for planar, axially compressible TDCRs that propagates equilibrium configurations along prescribed tendon-force and tendon-displacement trajectories. The backbone is represented by two global position fields. Following exact variation, a Taylor-Galerkin reduction condenses prescribed spatial properties and distributed loads into offline moment vectors, yielding analytic reduced residuals and Jacobians without online spatial quadrature or numerical differentiation. Analytical differentiation and residual correction yield first-order rate systems requiring one fixed-dimensional linear solve per rate evaluation after initial equilibrium alignment on a regular branch. Across four simulated cases covering variable tendon routing, nonuniform geometry, axial compression, and their combined effects, the propagated Cartesian shapes and distributed strains closely match pointwise geometrically variable-strain (GVS) equilibrium solutions. Residual correction suppresses propagation drift across the tested step sizes while adding only about 0.98% to the mean update time of uncorrected Euler. The proposed method requires 0.508 ms per update on average, approximately 11 times faster than pointwise GVS solves. Displacement-driven experiments yield a maximum normalized mean backbone position error of 1.02% and a maximum end-effector position error of 0.28%. These results support efficient and accurate Cartesian full-shape prediction along prescribed actuation paths.

0.30

An Open MuJoCo Simulation Framework for a Quadrotor Carrying a Tendon-Driven Soft Continuum Arm

cs.RO eess.SY ·2026-10-11 ·Haitham El-Hussieny
code/data similarity 0.59
Abstract

Combining aerial robots with soft continuum manipulators promises safe, compliant interaction with the environment, but the coupled dynamics of a free-flying base and a highly deformable, underactuated arm are difficult to study without a suitable simulator. This paper describes an open-source simulation framework, built on the MuJoCo physics engine, for a quadrotor that carries a tendon-driven soft continuum arm underneath its body. The arm is modelled as a pseudo-rigid-body chain of twelve segments joined by pairs of orthogonal compliant hinges. Three tendons, spaced \SI{120}{\degree} apart and routed through every segment, bend it in any direction. A geometric tracking controller on $SE(3)$ flies the vehicle; its rotor allocation matrix is generated directly from the model description. A closed-form tendon-tension allocation keeps every tension within its limits and gives the same bending moment in every direction. We report the full set of modelling choices and parameters, and we evaluate the framework in four simulated scenarios: a \SI{36}{\second} mission with a figure-eight and a tendon-driven tip sweep, an attitude-gain study, a quasi-static characterization of the bending workspace, and an impulsive disturbance applied to the arm tip. With the nominal gains the vehicle tracks the mission with \SI{3.1}{\centi\meter} RMS position error while the arm tip swings up to \SI{37}{\centi\meter} from the body axis. The gain study shows that a low-bandwidth attitude loop lets the arm excite sustained oscillations. The simulation runs about $15\times$ faster than real time on a laptop CPU. All models, controllers and scripts that reproduce the figures are released.

0.25

Real-Time Whole-Body Safe Motion Generation for Multi-Segment Tendon-Driven Continuum Robots

cs.RO ·2026-09-22 ·Fangju Yang, Siyi Ma, Tonghao Guan, Tingcong Liu, Hang Yang +3 more
hot direction similarity 0.58
Abstract

Real-time motion generation for tendon-driven continuum robots requires accurate modeling of nonuniform bending and whole-body collision avoidance. This paper presents a unified actuation-space framework for planar multi-segment tendon-driven continuum robots. An energy-based variable-curvature model captures spatially varying tendon spacing and bending stiffness and provides analytical Jacobians for differential inverse kinematics and safety monitoring. A multipoint CBF-QP enforces backbone clearance under obstacle motion and actuation-velocity bounds, while its decision dimension depends only on the number of independently actuated segments. The model closely agrees with GVS references, with a maximum curvature error of $5.223 \times 10^{-2}\,\mathrm{m}^{-1}$. Over 100 MuJoCo trials, the proposed method achieves collision-free success rates of 96% and 100% in static and dynamic scenarios, respectively, compared with approximately 60% and 80% without CBF constraints. Hole-traversal tests further demonstrate safe motion in constrained environments. With 600 backbone monitoring points, the mean control-step time is 6.66 ms, demonstrating real-time whole-body safe motion generation.

0.29

State estimation for a hybrid rigid-continuum space manipulator system

cs.RO ·2026-10-27 ·Lorenzo Ticozzi, Patricio A. Vela, Panagiotis Tsiotras
similarity 0.57
Abstract · 10 pages, 9 figures. Version submitted to "Soft Robotics"

Spacecraft-mounted robotic manipulators can support long-term operability of orbiting assets by conducting tasks such as on-orbit assembly, repair, upgrade, and refueling. In this context, the integration of continuum/soft robotic mechanisms into space manipulator designs promises to reduce stowage volume and mass, as well as to improve operational safety through the inherent mechanical compliance of soft structures. This work presents a novel state reconstruction pipeline for a hybrid soft-rigid space manipulator, in which the distal link is a tendon-driven continuum robot. The estimation problem is formulated as a maximum a posteriori (MAP) inference problem over the hybrid manipulator's configuration, conditioned on discrete, noisy measurements from joint encoders and a vision-based sensing pipeline. The resulting soft-constrained optimization problem is transcribed as a factor graph, providing a compact representation for fusing heterogeneous measurements with the rigid-soft kinematic model. Furthermore, the adoption of the Geometric Variable Strain (GVS) approach yields a minimum-order parameterization of the configuration, a property expected to facilitate model-based feedback control design in future work. The proposed implementation is validated in simulation on a closed-loop trajectory where, for better realism, position measurements for the continuum link are obtained by means of a simulated visual pipeline leveraging synthetic photorealistic images. The state reconstruction accuracy and computational performance confirm the potential of the proposed framework for hybrid soft-rigid robotic applications in orbit.

0.35

Adaptive Bendpoint Formation in Octopus-Inspired Soft Continuum Arms

cs.RO ·2026-10-18 ·Jessica Gumowski, Julian Finn, Krishna Manaswi Digumarti, David Howard
similarity 0.55
Abstract

Octopuses exhibit a powerful form of embodied intelligence from a highly adaptable soft body. One key mechanism is the ability to instantiate bending points at any location along the arm, which enables performant and dexterous behaviours. Taking inspiration from the octopus for its dexterity, this study focuses on changing the curvature of a tendon-actuated arm by adaptively changing the anchoring end-point along the arm. An array of inflatable shells is integrated into the arm, where inflating a shell causes an increase in friction at the location, jamming the tendon and creating a temporary new anchoring point. The novel soft actuator does not break the continuity of the arm between the actuated segment and the loose segment. Experiments show that the actuated segment has a non-constant bell-shaped curvature which is comparable to that of a real octopus arm during a reaching motion. Compared to conventional single-tendon continuum manipulators, the proposed design offers an expanded workspace and enhanced dexterity through the ability to independently shape different regions of the arm through selective curvature tuning. At the same time, it avoids the mechanical complexity typically associated with multi-segment, multi-actuator systems.

0.14