CS Paper Radar

Adaptive Bendpoint Formation in Octopus-Inspired Soft Continuum Arms

Jessica Gumowski, Julian Finn, Krishna Manaswi Digumarti, David Howard

cs.RO ·submitted 2026-10-18 23:29 UTC · v1

Abstract

Octopuses exhibit a powerful form of embodied intelligence from a highly adaptable soft body. One key mechanism is the ability to instantiate bending points at any location along the arm, which enables performant and dexterous behaviours. Taking inspiration from the octopus for its dexterity, this study focuses on changing the curvature of a tendon-actuated arm by adaptively changing the anchoring end-point along the arm. An array of inflatable shells is integrated into the arm, where inflating a shell causes an increase in friction at the location, jamming the tendon and creating a temporary new anchoring point. The novel soft actuator does not break the continuity of the arm between the actuated segment and the loose segment. Experiments show that the actuated segment has a non-constant bell-shaped curvature which is comparable to that of a real octopus arm during a reaching motion. Compared to conventional single-tendon continuum manipulators, the proposed design offers an expanded workspace and enhanced dexterity through the ability to independently shape different regions of the arm through selective curvature tuning. At the same time, it avoids the mechanical complexity typically associated with multi-segment, multi-actuator systems.

Closest papers

Nearest neighbours by meaning across the whole index.

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.68
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Towards end-to-end co-design for one-shot printable task-specific soft robots

cs.RO ·2026-11-02 ·James Wood, André Farinha, Will Browne, Josh Pinskier, Krishna Manaswi Digumarti
similarity 0.66
Abstract

Soft robot co-design methods can jointly optimise morphology and control, but the resulting designs are often difficult to manufacture, while manufacturable approaches typically restrict actuator placement or require manual assembly. We present a simulation-based co-design framework that jointly optimises material distribution, pneumatic actuator placement and orientation, and control, while producing designs that can be fabricated monolithically using fused deposition modelling. The framework uses a differentiable 2D plane-stress Material Point Method simulator, incorporating an experimentally validated material model and an empirically derived surrogate model of a 3D-printed inflatable actuator. We demonstrate gradient-based optimisation soft robotic arms for prescribed tip trajectories. Optimised designs are transferred directly from simulation to one-shot monolithic FDM fabrication, with integrated actuators and no post-assembly. Physical experiments demonstrate that the resulting arms reproduce the behaviour predicted in simulation. This framework provides a path from task-level objectives to physically realisable soft robots while retaining substantial freedom over both morphology and actuation.

0.14

Tip Manipulation in Soft Everting Robots via Wall Retraction and Deployable Fingers

cs.RO ·2026-09-19 ·Nelson Badillo Perez, Niccolo Pagliarani, Matteo Cianchetti, Robert D. Howe
similarity 0.66
Abstract · 38 pages, 6 figures and supplementary information

Soft everting robots can traverse long, confined paths by continuously growing, yet active interaction remains limited to a single tool fixed at or near the tip, unable to be repositioned on demand and difficult to reconcile with the robot's soft body. We introduce a tip-manipulation and multi-tool deployment strategy for soft everting robots based on wall retraction, implemented with a base roller assembly that independently meters membrane flow in the outer wall while a tail spool regulates growth in the internal tail section. Coordinated wall and tail actuation decouples robot length from membrane-material position, enabling membrane-mounted devices to be transported, exposed, and repositioned at selected locations near the distal tip. We pair this capability with ultralight pleated inflatable fingers integrated into the membrane, fabricated from TPU-coated nylon with an internal airtight bladder. The fingers achieve large bending at low pressures (approximately 100 degrees at 50 kPa in high-pleat designs) and generate blocking forces up to 1.9 N, while remaining limp during transport. The system demonstrates adaptive grasping across diverse household objects (21 to 550 g; 16 to 200 mm), three-dimensional object manipulation and stacking, environmentally braced extension, distal camera panning for confined-space inspection, and controlled sequential payload delivery. These results enable embodied and reversible tip manipulation for soft growing robots in cluttered and tortuous environments.

0.25

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.65
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

A Support-Enhanced Granular-Jamming Gripper for RL-based Grasping with Continuum Manipulators

cs.RO ·2026-09-24 ·Danyu Liu, Tianlin Zhang, Wei Chen, Wei Tang, Kecheng Qin +1 more
hot direction similarity 0.65
Abstract · 8 pages, 10 figures

Continuum manipulators provide dexterous motion in confined spaces, but structural compliance, hysteresis, and load-dependent deformation leave residual position and orientation errors that can undermine reliable contact with rigid grippers. To address this limitation, this paper presents a lightweight support-enhanced granular-jamming gripper tailored to a continuum manipulator. The gripper maintains compliance before jamming while establishing a direct load path to the continuum manipulator tip after jamming. To improve its grasping performance, we systematically designed membrane materials, particles, filling ratios, and the internal support structure, and further identify geometry-dependent grasp boundaries with respect to contact offset and object shape. Building on these results, we construct a physical manipulation system integrating the continuum manipulator, granular-jamming gripper, visual feedback, tendon actuation, and pneumatic control. We then train a reinforcement-learning-based reaching controller in a randomized simulation and deploy it on the physical system, demonstrating how positioning control and contact level mechanical adaptation can complement each other in a modular grasp-and-release task. By introducing an adaptive structure that relaxes the need for highly accurate modeling and positioning control, this work explores a design paradigm that integrates physical and embodied intelligence.

0.55

Embodied Snap: Octopus-Inspired Distributed Reach-and-Attach with a Speed-Limited Soft Arm

cs.RO ·2026-09-19 ·Linxin Hou, Zhihang Qin, Heyang Zou, Qirui Wu, Peiyi Wang +3 more
hot direction similarity 0.64
Abstract

Reach-and-attach of soft robotic arms with passive suction requires accurate targeting and sufficient contact speed, yet geared actuators can impose a speed limit that improved trajectory tracking alone cannot overcome. This paper proposes an embodied snap controller that separates slow servo-driven preloading from rapid elastic release, enabling a compliant arm to move beyond its direct tendon-driven speed limit. Octopus biology motivates the controller's section-wise organizational prior, rather than reproduction of the octopus nervous system. A learned policy shared across three sections selects preloads, aim, tendon slack, and release timing, determining where, how, and when to load and release the body. The policy is optimized offline using a hardware-validated recurrent model within experimentally supported bounds. Across five optimization seeds and 400 unseen simulated targets, attachment success is $(73\pm4)\%$ at a $5\text{ cm}$ lateral tolerance, and the shared policy reaches the matched centralized controller's mean final reward after a median $17\%$ of the common evaluation budget. Hardware characterization achieves tip speeds of 1.56-1.64 m/s, at least $108\%$ above direct tendon-driven release. In 18 open-loop hardware trials across six placements, 17 exceed the 1 m/s snap threshold and nine retrieve the object, with successful retrieval at five placements. These results demonstrate a practical division of responsibility in the control problem: learned control prepares the body, and passive body mechanics execute the rapid movement needed for dynamic reach-and-attach.

0.28

Optimize, Learn, Refine: Whole-Body Grasping and Pick-and-Throw with a Spiral Soft Robot

cs.RO ·2026-09-22 ·Marwah Basuhai, Tingcong Liu, Ibrahim Alsarraj, Yuhao Wang, Ke Wu
hot direction similarity 0.64
Abstract

Soft continuum robots can exploit distributed compliance for whole-body manipulation, but synthesizing behavior through changing contacts remains difficult. We address whole-body grasping and pick-and-throw from an initially ungrasped state through outcome-based actuation-space optimization. Grasping is quantified by tip angular sweep and body-object enclosure, while throwing further incorporates release-direction alignment and minimum release speed. These objectives allow grasping, acceleration, and release to emerge from compliant interaction without prescribing contact forces, contact locations, or body configurations. Because the resulting actuation-to-outcome mapping is nonsmooth, we utilize derivative-free CMA-ES within an optimize-learn-refine framework. CMA-ES generates solutions for sampled conditions, a task-conditioned predictor learns warm starts, and CMA-ES refines them for unseen conditions. In simulation, the method achieves 492/500 successful grasps (98.4%) and success rates of 98%, 97%, and 94% across three directional throwing trials. Learned initialization increases grasping success from 78.6% to 98.4% while reducing the median rollout count from 1184 to 816 in CMA-ES. Hardware experiments achieve a 100% grasping success rate across 50 executions and a 100% pick-and-throw success rate across 30 executions, with 10 repetitions per direction. Together, these simulation and hardware results demonstrate the effectiveness of the proposed framework across both simulated and physical whole-body manipulation tasks.

0.26

Real-Time Shape Control of Multi-Segment Soft Robotic Arms Using Koopman Operators with Global and Local Observables

cs.RO eess.SY ·2026-09-02 ·Jiahe Wang, Eron Ristich, Sultan Haidar Ali, Eric weissman, Lei Zhang +3 more
similarity 0.64
Abstract · 18 pages, 14 figures, submitted to TRO

Multi-segment soft robotic arms can continuously reconfigure their body shapes for safe interaction, but tip control alone is insufficient for constrained-space tasks. Therefore, shape control is a more important task for multi-segment soft arms than tip control, but remains challenging due to the high dimensionality and nonlinear dynamics of continuum deformation. In existing work, shape control accuracy is defined by the error in the global frame (global shape error). For multi-segment soft arms, using only global shape error as the control objective is insufficient, as segment coupling, gravity-induced loading, and inertial effects become more significant. This difficulty increases with the number of segments. In this paper, we present a Koopman-based model predictive control framework that combines global and local observables, enabling real-time shape control on multi-segment soft robotic arms. The framework is evaluated through numerical and physical experiments. Numerical experiments demonstrate the scalability of the proposed controller by achieving shape control on robots with up to 10 independently actuated segments. The physical experiments demonstrate that the controller is capable of (1) real-time shape control of 3- and 5-segment robotic arms with tip speeds up to 0.6 m/s, (2) robust tracking without retraining, including distal payloads up to 400~g and recovery from a 7~N lateral disturbance, and (3) the potential for future inspection applications through a confined-space demonstration. These results demonstrate that the proposed framework enables dynamic, scalable, and accurate real-time shape control on multi-segment soft robotic arms.

0.35