CS Paper Radar

Embodied Snap: Octopus-Inspired Distributed Reach-and-Attach with a Speed-Limited Soft Arm

Linxin Hou, Zhihang Qin, Heyang Zou, Qirui Wu, Peiyi Wang, Muhammad Sunny Nazeer, Yongxin Guo, Cecilia Laschi

cs.RO ·submitted 2026-09-19 10:13 UTC · v2
hot direction

Abstract

Reach-and-attach of soft robotic arms with passive suction requires accurate targeting and sufficient contact speed, yet geared actuators can impose a speed limit that improved trajectory tracking alone cannot overcome. This paper proposes an embodied snap controller that separates slow servo-driven preloading from rapid elastic release, enabling a compliant arm to move beyond its direct tendon-driven speed limit. Octopus biology motivates the controller's section-wise organizational prior, rather than reproduction of the octopus nervous system. A learned policy shared across three sections selects preloads, aim, tendon slack, and release timing, determining where, how, and when to load and release the body. The policy is optimized offline using a hardware-validated recurrent model within experimentally supported bounds. Across five optimization seeds and 400 unseen simulated targets, attachment success is $(73\pm4)\%$ at a $5\text{ cm}$ lateral tolerance, and the shared policy reaches the matched centralized controller's mean final reward after a median $17\%$ of the common evaluation budget. Hardware characterization achieves tip speeds of 1.56-1.64 m/s, at least $108\%$ above direct tendon-driven release. In 18 open-loop hardware trials across six placements, 17 exceed the 1 m/s snap threshold and nine retrieve the object, with successful retrieval at five placements. These results demonstrate a practical division of responsibility in the control problem: learned control prepares the body, and passive body mechanics execute the rapid movement needed for dynamic reach-and-attach.

Closest papers

Nearest neighbours by meaning across the whole index.

Diverse and Adaptable Arm Coordination for Octopus-Crawling via Diffusion-Based Uncertainty-Aware Optimization

cs.RO cs.LGmath.OC ·2026-09-17 ·Seung Hyun Kim, Heng-Sheng Chang, Kimia Kazemi, Prashant Mehta, Mattia Gazzola
similarity 0.68
Abstract · 8 pages, 5 figures, submitted to ICRA 2027

Octopus crawling motivates soft robots that exploit redundancy, yet discovering and organizing diverse coordination modes for adaptation remains challenging. To address this, we introduce a Diffusion-based Uncertainty-aware Optimization (DUO) algorithm that learns demonstration-free crawling controllers for a simulated, muscle-actuated CyberOctopus. This work represents the first application of diffusion-based control to soft multi-arm robots in contact-rich simulations. By embedding a variety of locomotion behaviors within a shared control distribution, this approach enables the simulated octopus to navigate dynamic physical constraints, demonstrating that learned coordination diversity inherently facilitates robust adaptation. The main contributions include: (i) a symmetry-structured policy representation that folds radially equivalent controllers into a canonical directional sector, (ii) an online black-box optimization strategy, the DUO algorithm, that discovers and retains diverse coordination modes, and (iii) a control editing technique that adapts existing controllers to novel actuator constraints without retraining. These results show how learned coordination diversity makes motor abundance a practical resource for adaptation in soft multi-arm robots.

0.50

Optimize, Learn, Refine: Whole-Body Grasping and Pick-and-Throw with a Spiral Soft Robot

cs.RO ·2026-09-22 ·Marwah Basuhai, Tingcong Liu, Ibrahim Alsarraj, Yuhao Wang, Ke Wu
hot direction similarity 0.66
Abstract

Soft continuum robots can exploit distributed compliance for whole-body manipulation, but synthesizing behavior through changing contacts remains difficult. We address whole-body grasping and pick-and-throw from an initially ungrasped state through outcome-based actuation-space optimization. Grasping is quantified by tip angular sweep and body-object enclosure, while throwing further incorporates release-direction alignment and minimum release speed. These objectives allow grasping, acceleration, and release to emerge from compliant interaction without prescribing contact forces, contact locations, or body configurations. Because the resulting actuation-to-outcome mapping is nonsmooth, we utilize derivative-free CMA-ES within an optimize-learn-refine framework. CMA-ES generates solutions for sampled conditions, a task-conditioned predictor learns warm starts, and CMA-ES refines them for unseen conditions. In simulation, the method achieves 492/500 successful grasps (98.4%) and success rates of 98%, 97%, and 94% across three directional throwing trials. Learned initialization increases grasping success from 78.6% to 98.4% while reducing the median rollout count from 1184 to 816 in CMA-ES. Hardware experiments achieve a 100% grasping success rate across 50 executions and a 100% pick-and-throw success rate across 30 executions, with 10 repetitions per direction. Together, these simulation and hardware results demonstrate the effectiveness of the proposed framework across both simulated and physical whole-body manipulation tasks.

0.26

CALM: Current Aligned Link Manipulation for Single Arm Oversized Object Lifting

cs.RO ·2026-09-24 ·Jun Hu, Sihan Chen, Kosta Jovanovic, David Navarro-Alarcon, Xueqian Wang +2 more
similarity 0.65
Abstract

Most robots manipulate objects solely with their end effectors, whereas humans flexibly leverage different body parts, such as the forearm and elbow, especially when handling oversized objects. Learning such whole-arm manipulation is chal-lenging due to long-horizon sparse rewards, limited contact sens-ing, and the sim-to-real gap in contact and actuator dynamics. To address these challenges, we propose Current-Aligned Link Manipulation, a framework for learning long-horizon contact-rich manipulation using motor current as joint load related feedback. Three stage-specific policies first learn repositioning, grasping, and lifting using privileged simulation information, and a stage router sequences them to generate complete task demonstrations. For sim-to-real transfer, a causal current mapper predicts physical motor current from simulated joint histories, aligning the actuator current observation between simulation and hardware. A unified student policy then learns from these demonstrations using only deployable sensor observations and is further refined with DAgger. The task policies are trained entirely in simulation, and the final student is deployed on hardware. Experiments demonstrate 76.2% (762/1000 trials) complete-task success in simulation and 73.3% success (22/30 trials) on the physical robot for sequential oversized-object lifting.

0.23

Adaptive Bendpoint Formation in Octopus-Inspired Soft Continuum Arms

cs.RO ·2026-10-18 ·Jessica Gumowski, Julian Finn, Krishna Manaswi Digumarti, David Howard
similarity 0.64
Abstract

Octopuses exhibit a powerful form of embodied intelligence from a highly adaptable soft body. One key mechanism is the ability to instantiate bending points at any location along the arm, which enables performant and dexterous behaviours. Taking inspiration from the octopus for its dexterity, this study focuses on changing the curvature of a tendon-actuated arm by adaptively changing the anchoring end-point along the arm. An array of inflatable shells is integrated into the arm, where inflating a shell causes an increase in friction at the location, jamming the tendon and creating a temporary new anchoring point. The novel soft actuator does not break the continuity of the arm between the actuated segment and the loose segment. Experiments show that the actuated segment has a non-constant bell-shaped curvature which is comparable to that of a real octopus arm during a reaching motion. Compared to conventional single-tendon continuum manipulators, the proposed design offers an expanded workspace and enhanced dexterity through the ability to independently shape different regions of the arm through selective curvature tuning. At the same time, it avoids the mechanical complexity typically associated with multi-segment, multi-actuator systems.

0.14

Learning Reflexive Behavior for Contact-Rich Manipulation

cs.RO ·2026-10-02 ·Quan Nguyen, Yunho Kim, Joonho Lee
similarity 0.63
Abstract

During contact-rich manipulation, interactions between a robot and its environment carry information about local geometry: a surface prevents penetration, a bore guides a peg. A controller that exploits these interactions can comply with environmental constraints while preserving task intent. Robot-earning systems commonly use position, hybrid force-position, or Cartesian impedance control. Their prescribed tracking objectives, stiffness, or force-control directions may not match local constraints and may degrade performance. We learn a proprioceptive reflex policy in simulation on three simple interaction primitives: a spring, a plane, and a rail. The policy maps task-space commands to joint-position targets using state history, without direct force or geometrical measurements. Once trained, it serves as a frozen execution layer beneath higher-level controllers. We evaluate it in dual-arm box lifting, peg insertion, and surface following. In box lifting, the reflex kept the force below the threshold while the baseline failed. In rough-surface following it stayed below the 10 N reference, on par with tuned hybrid force-position control. In 0.02 mm peg insertion It reduced mean estimated contact force to less than half that of the baseline while increasing hardware success rates from at most 22 % to 36-58 %. By separating contact response from command generation, the reflex policy provides motion planners, learned policies, and teleoperators with robust contact-rich execution.

0.15

PolyMorphWBC: Whole-Body Control from End-Effector Trajectories for Quadrupedal Mobile Manipulation across Arm Morphologies with Extended Reach

cs.RO ·2026-11-11 ·Heng Li, Yang Li, Yifan Duan, Ren Fang, Matao Duan +4 more
similarity 0.63
Abstract · 8 pages, 4 figures

Quadrupedal mobile manipulators can extend their manipulation workspace by coordinating the mounted arm with the mobile base. At the task level, short-horizon end-effector (EE) trajectories provide an interface for specifying the desired manipulation motion without prescribing how it should be realized by the arm and base. However, executing such trajectories remains challenging because the controller must determine when and how the base should move, and this decision depends on the mounted-arm morphology. We therefore present PolyMorphWBC, a hierarchical controller that takes an EE trajectory as the sole task-level motion command and generates coordinated arm--base motions across four families of 6-DoF mounted arms, with extended-reach trajectories beyond the initial fixed-base reach. Within PolyMorphWBC, a trajectory-conditioned coordinator determines the base motion from previewed EE targets, while arm-specific Inverse Kinematics (IK) tracks the current target, and a frozen locomotion backend executes the resulting motion. Cross-arm reuse is enabled by a Unified Robot Description Format (URDF)-derived morphology conditioning, together with online residual-wrench feedback. We train PolyMorphWBC on procedurally generated arms and structured trajectories within and beyond fixed-base reach. In IsaacLab, it achieves 93.95% completion with 2.30cm position error and 4.81° orientation error on held-out trajectories and arm morphologies. In MuJoCo evaluation against UMI-on-Legs, PolyMorphWBC reduces EE position error by 69--72% and orientation error by 91--97% across four within- and extended-reach trajectories. On a physical Go2--ARX5 system, we demonstrate language-conditioned extended-reach pick-and-place using EE trajectories from pi_0 without vision-language-action (VLA)-generated base commands.

0.13

Learning to Leverage Compliance: A Policy-Admittance Learning Framework for Robotic Insertion

cs.RO ·2026-09-25 ·Chongren Wang, Minghe Li, Honghua Dai, Zhicheng Lin, Shiyang Wei +1 more
similarity 0.63
Abstract

Policy learning and compliant control offer a promising route to reliable autonomous assembly under pose errors and contact uncertainty. However, combining them does not ensure coordination: the policy may continue pushing against contact while the controller yields, producing sustained loading with limited progress. To address this problem, we propose LeCo (Leverage Compliance), a policy-admittance learning framework that guides a visual policy through execution-time interaction under fixed admittance. A multirate feedback mechanism aggregates high-rate contact-interaction records into policy-transition rewards. An integrated conflict cost then characterizes sustained policy-loading/controller-unloading opposition, while a directional high-force tail cost captures continued-loading events within a transition. Together with task completion, these costs encourage the policy to leverage compliance with less unproductive loading. We evaluate LeCo on four real connector-assembly tasks, obtaining an aggregate success rate of 94%. Across tasks, mean successful-trial resultant-force and torque peaks decrease by approximately 30% and 64% relative to the comparison baseline. Reward ablation further shows that adding conflict shaping reduces median successful-trial contact-conditioned conflict density by approximately 53%. These results support learning to leverage fixed compliance by turning multirate policy-admittance interaction into complementary reward signals for effective, lower-load insertion.

0.23

Non-Prehensile Throwing: A Reinforcement Learning Perspective

cs.RO ·2026-09-01 ·Abdullah Mustafa, Ryo Hanai, Ixchel G. Ramirez-Alpizar, Floris Erich, Ryoichi Nakajo +2 more
published similarity 0.62
Abstract · 8 pages, 9 figures, Accepted to IEEE IROS 2026

Robotic throwing enables fast object transport and extends a robot's reachable workspace beyond traditional pick-and-place. While prehensile (grasp-based) throwing works well for graspable items, non-prehensile (grasp-free) throwing is better suited for large, heavy, and/or deformable objects. Existing approaches rely on model-based optimization with simplified contact models (e.g., dynamic grasping) and low-dimensional trajectory parameterizations, which limit solution quality and reachable workspace. We propose a reinforcement learning approach that additionally leverages sliding and rolling contact modes and directly optimizes joint-space trajectories without analytical contact models or custom parameterizations. The Markov Decision Process (MDP) is formulated as a dynamical system that evolves the robot's joint state conditioned on the throwing target, object model, and initial configuration. Joint-jerk trajectories are planned offline at a low control rate and upsampled into smooth, high-rate velocity commands for deployment. For sim-to-real transfer, we minimize the robot-dynamics gap through minimum-jerk system identification and train uncertainty-aware policies to mitigate object-modeling errors, particularly sensitivity to dynamic friction. In simulation, the policy achieves 99% success across thousands of configurations and generalizes to unseen objects. Sensitivity analysis shows robustness to mass uncertainty but high sensitivity to dynamic friction, consistent with the sliding-based release mechanism. Deployed zero-shot on a UR5e operating near its physical limits (5 m/s end-effector velocity), our method throws diverse objects including heavy (790 g) and large (20x20x28 cm) items to targets up to 350 cm distance or 180 cm elevation, achieving a 97% real-world success rate.

0.25