CS Paper Radar

Design and Characterization of a Variable-Length Continuum Mechanism with Force Locking

Katelyn King, Veronica Fish, Allison M. Okamura

cs.RO ·submitted 2026-09-25 03:37 UTC · v1
hot direction

Abstract

The utility of flexible continuum mechanisms for dexterous navigation is often impaired by their low stiffness, making them ineffective at manipulation in high-force scenarios. To address this challenge, we propose a novel continuum mechanism that achieves both flexible and rigid behavior by antagonistic extension and contraction of a rod-driven continuum helical structure. The helical design combines variable-length capacity with force locking for workspace and stiffness enhancement. In this article, we present the detailed design of the proposed mechanism and characterize its performance through experiments that quantify bending and stiffness. The results demonstrate 180 degree bending range of motion with an average distal positioning error of <10%. Further tests demonstrate that force locking directly improves axial stiffness and thus indirectly increases bending stiffness anisotropically, with maximum bending stiffness along load paths with a large axial component. Tensioning the driving rods provides additional stiffness tunability in the force-locked state, where increasing rod tension proportionally increases bending stiffness with a dimensionless gain of 0.56.

Comment
7 pages, 9 figures. Submitted to ICRA 2027. Ancillary files contain a supplementary video

Closest papers

Nearest neighbours by meaning across the whole index.

Curvature by Design: A Support Structure for Continuum Robots

cs.RO ·2026-11-04 ·Justus Sagemüller, Harald Minde Hansen, Kristin Y. Pettersen
similarity 0.72
Abstract

Constant- and piecewise-constant-curvature models are widely used to simplify the kinematics of continuum robots, although the assumed curvature profiles are not necessarily inherent mechanical properties of the robot and may therefore be violated during operation. Rather than assuming a prescribed curvature profile in the kinematic model and estimating deviations from it, this paper presents a multi-segment scissor-based support structure that mechanically constrains a continuum robot to exhibit prescribed constant or spatially varying curvature profiles. The design uses Taylor approximations to enable an overconstrained multi-joint linkage to predictably distribute global bending among the small-angle movements of multiple flexures. The geometric coupling is realized using compliant flexure joints, enabling the support structure to be manufactured as a single piece. The structure is integrated with a tendon-actuated continuum robot with a flexible backbone. Experiments show that the structure makes the robot resistant to deformations other than the prescribed curvature, significantly enhancing shape precision compared to classical flexible-backbone designs. This constrains the robot from making S-shapes when external loads are applied in the opposite direction of the bending. By mechanically constraining the admissible deformation, the proposed structure reduces the number of independent shape variables that must be estimated.

0.11

Closed-Form Cartesian Forward Kinetostatics for Spatial Multi-Segment Tendon-Driven Continuum Robots

cs.RO ·2026-09-29 ·Ke Wu, Fangju Yang, Xiaohui Zhang, Junda He, Guanjun Bao +2 more
benchmark similarity 0.69
Abstract

Forward kinetostatics of spatial tendon-driven continuum robots typically requires a nonlinear equilibrium solve for each actuation input. This paper develops a force-to-Cartesian-configuration model with a closed-form solution in quadratures for spatial multi-segment robots under tendon actuation. The Cartesian backbone centerline and accumulated material twist serve as generalized coordinates, from which the strain measures and tendon geometry are derived. Variational equilibrium yields explicit axial and bending relations and establishes zero equilibrium material twist within the proposed model for admissible longitudinal non-helical routing. The solution is propagated segment by segment without an iterative equilibrium solve, while retaining axial deformation, spatially varying axial and bending stiffnesses and tendon-routing diameter, and segment-dependent tendon participation. Numerical comparisons with a full-strain geometric variable-strain model (GVS) yield maximum length-normalized tip-position discrepancies of 8.91 x 10^-6 and 1.01 x 10^-5 for the single- and three-segment robots, respectively. Mean evaluation times of 1.52 μs and 2.94 μs, with corresponding speedups of approximately 1864x and 3348x over the baseline, demonstrate the computational advantage of the explicit force-to-configuration mapping in the reported benchmark.

0.14

Design and Characterization of a Unified Continuum Robot Actuation Platform

cs.RO ·2026-10-14 ·Yunti Xu, Aedan Mangan, Miheer Potdar, Alex Lu, Tania K. Morimoto
similarity 0.62
Abstract

Continuum robots enable dexterous access to confined spaces in applications such as minimally invasive surgery and industrial inspection. However, their actuation systems are often custom-designed for specific robot architectures and tasks, limiting reuse across publications, institutions, and applications. This paper presents a unified actuation platform that decouples actuation hardware and software from continuum robot design. The platform provides modular actuation across continuum robot classes, scales to a large number of degrees of freedom (DOFs), and integrates with conventional serial manipulators for hybrid architectures. We validate the platform on an open-sourced surgical robotic system and experimentally characterize the actuation modules, achieving sub-millimeter translational accuracy and less than $5^\circ$ rotational error over ranges of $30$~mm and $180^\circ$, respectively. We further demonstrate the platform in two surgical use cases: teleoperation of a continuum camera in a constrained environment and bimanual manipulation using $2.53$~mm concentric-tube-robot-based forceps alongside a conventional wristed instrument. All hardware designs and ROS-based software are open-sourced to facilitate reuse and further research in continuum and surgical robotics.

0.31

A Support-Enhanced Granular-Jamming Gripper for RL-based Grasping with Continuum Manipulators

cs.RO ·2026-09-24 ·Danyu Liu, Tianlin Zhang, Wei Chen, Wei Tang, Kecheng Qin +1 more
hot direction similarity 0.62
Abstract · 8 pages, 10 figures

Continuum manipulators provide dexterous motion in confined spaces, but structural compliance, hysteresis, and load-dependent deformation leave residual position and orientation errors that can undermine reliable contact with rigid grippers. To address this limitation, this paper presents a lightweight support-enhanced granular-jamming gripper tailored to a continuum manipulator. The gripper maintains compliance before jamming while establishing a direct load path to the continuum manipulator tip after jamming. To improve its grasping performance, we systematically designed membrane materials, particles, filling ratios, and the internal support structure, and further identify geometry-dependent grasp boundaries with respect to contact offset and object shape. Building on these results, we construct a physical manipulation system integrating the continuum manipulator, granular-jamming gripper, visual feedback, tendon actuation, and pneumatic control. We then train a reinforcement-learning-based reaching controller in a randomized simulation and deploy it on the physical system, demonstrating how positioning control and contact level mechanical adaptation can complement each other in a modular grasp-and-release task. By introducing an adaptive structure that relaxes the need for highly accurate modeling and positioning control, this work explores a design paradigm that integrates physical and embodied intelligence.

0.54

Capstan-driven Continuum Surgical Robot: Design, Modeling, and Perception

cs.RO ·2026-08-13 ·Gang Zhang, Yufu Qiu, Junyan Yan, Wenhui Zeng, Wenlong Lu +1 more
similarity 0.61
Abstract

Shape and force sensing have long been critical bottlenecks in the development of compact capstan-driven continuum surgical robots, primarily due to the difficulty of obtaining cable tension information within the confined capstan assembly. To overcome these challenges, this paper presents an integrated design-modeling-sensing approach based on the concept of actuation-perception co-design. A compliant element is introduced into the motor mounting bracket of the drive system, enabling micro-deformation under the cable reaction force and thereby allowing real-time cable tension measurement without occupying the compact capstan space. To address the modeling complexity arising from unconventional joint configurations introduced by the spatial cable routing strategy, a parallel computation framework based on a multibody short-thick-beam model is proposed, which captures shear effects in short beam segments and synergistic multi-cable interactions while achieving real-time performance. Building on this framework, stable shape and force sensing is achieved by incorporating a proximal multi-axis force/torque sensor as an additional measurement anchor. Following this design-modeling-sensing framework, capstan-driven continuum surgical robots with single- and dual-segment configurations are developed. Experimental results validate the proposed framework in both single- and dual-segment continuum robots, demonstrating real-time tip pose estimation together with contact force and location perception. By enabling cable tension feedback without compromising the compact capstan architecture, the proposed framework makes integrated perception feasible for capstan-driven continuum surgical robots.

0.04

Real-Time Whole-Body Safe Motion Generation for Multi-Segment Tendon-Driven Continuum Robots

cs.RO ·2026-09-22 ·Fangju Yang, Siyi Ma, Tonghao Guan, Tingcong Liu, Hang Yang +3 more
hot direction similarity 0.60
Abstract

Real-time motion generation for tendon-driven continuum robots requires accurate modeling of nonuniform bending and whole-body collision avoidance. This paper presents a unified actuation-space framework for planar multi-segment tendon-driven continuum robots. An energy-based variable-curvature model captures spatially varying tendon spacing and bending stiffness and provides analytical Jacobians for differential inverse kinematics and safety monitoring. A multipoint CBF-QP enforces backbone clearance under obstacle motion and actuation-velocity bounds, while its decision dimension depends only on the number of independently actuated segments. The model closely agrees with GVS references, with a maximum curvature error of $5.223 \times 10^{-2}\,\mathrm{m}^{-1}$. Over 100 MuJoCo trials, the proposed method achieves collision-free success rates of 96% and 100% in static and dynamic scenarios, respectively, compared with approximately 60% and 80% without CBF constraints. Hole-traversal tests further demonstrate safe motion in constrained environments. With 600 backbone monitoring points, the mean control-step time is 6.66 ms, demonstrating real-time whole-body safe motion generation.

0.29

Tensegrity Continuum Robots Enable Task-Adaptive Morphologies for Cooperative Behaviors

cs.RO ·2026-08-27 ·Mahmud Hasan Saikot, Sydney Spiegel, Sudheera Akalanka Kariyawasam, Andrew Stefka, Josh Chrisler +1 more
top venue similarity 0.59
Abstract · 22 pages, 6 figures, Accepted to Nature Machine Intelligence

Robots that can change their morphologies and behaviors for different tasks and environments hold great promise for adaptable, multifunctional systems. Modular reconfigurable robots (MRRs) can achieve such functionalities by docking and rearranging individual units, but most rely on rigid modules that lack structural compliance, resulting in limited capabilities. Continuum robots offer compliance through flexible backbones, yet they cannot self-reconfigure into task-adaptive multi-robot configurations. Here, we introduce an MRR that unifies the advantages of both architectures by combining a tensegrity-based compliant body with claw-based connection mechanisms. Each robot can manipulate and locomote independently, and multiple robots can self-reconfigure into different morphologies (e.g., chains, loops, branches) for cooperative manipulation and locomotion. We demonstrate the robots' capability across diverse tasks and environments, including coordinated object manipulation and transport, multimodal locomotion, and loco-manipulation in real-world scenarios. These results lay a foundation for adaptable and multifunctional robotic collectives, with broad potential applications in manufacturing, space exploration, and search-and-rescue operations.

0.33

Cosserat Modeling of Trimmed Helicoid Soft Arms with a Separated-Section Constitutive Law

cs.RO ·2026-09-21 ·Zhihang Qin, Linxin Hou, Zeyu Zhong, Yuchen Sun, Wenci Xin +8 more
similarity 0.59
Abstract

Cosserat rod models for soft robots usually construct sectional stiffness by summing material properties over a common cross-section. This assumption becomes inaccurate for trimmed helicoid arms, where load-bearing helix domains are separated and connected only through sparse fused crossings. This paper formulates a separated-section constitutive law that evaluates each helix domain in its local frame and pulls its constitutive response back to the backbone, yielding an effective backbone stiffness. Sparse-fusion mechanics captures the additional compliance caused by relative motion between neighboring domains and determines channel-wise reduction profiles $η_c(s/L)$ for bending, torsion, and extension. The resulting effective sectional stiffness is strongly anisotropic: bending and extension are reduced by about one order of magnitude, whereas torsion remains close to the effective backbone stiffness. The resulting sectional law is embedded in a geometrically exact dynamic Cosserat model with GVS discretization and routed-tendon actuation. Across 103 measured configurations, the three datasets give pooled normalized position errors of $7.7 \ \%$, $6.7 \ \%$, and $7.8 \ \%$, while each full-arm solve requires approximately $0.3 \ \mathrm{s}$ on one CPU core (Intel Xeon, Cascade Lake, $2.8 \mathrm{GHz}$), enabling rapid model-based planning, state and load estimation, and morphology--control co-design for architected soft robots.

0.38