CS Paper Radar

Instrumentation and Stabilization of Electric Arcs for Plasma Smelting Reduction

Thomas Voglhuber-Brunnmaier, Lukas Ecker, Benjamin Lehner, Jakob Stanek, Erwin K. Reichel

eess.SY ·submitted 2026-10-08 12:38 UTC · v1
unusual

Abstract

The Hydrogen Plasma Smelting Reduction (HPSR) is a promising technology for low-CO$_2$ steel production. However, unstable arc conditions limit energy efficiency, hydrogen utilization, and electrode wear. In this paper, we discuss the influence of the electrical supply characteristics, which can be a source of additional instability. For active stabilization, a fast current controller using a buck converter with an adaptive state controller is used. For analyzing arc stability, a stereoscopic measurement system for reconstructing the arc is presented. The results show a clear correlation between the arc lengths and the measured arc voltage at constant current. Therefore, arc stability can be determined by the measured voltage. These findings build the basis for dynamic arc control by fast electrical interventions.

Comment
15 pages, 16 figures,

Closest papers

Nearest neighbours by meaning across the whole index.

A 2D Axisymmetric Multi-Domain DC Arc Model for Simulink Implementation

eess.SY math-ph ·2026-08-23 ·Vinod Kumar Maddineni, Rahul Reddy Devarapally, Nihar Panchal, NagaBabu Koganti, Addisalem Kokob W. +1 more
publishedunusual similarity 0.52
Abstract

This study introduces a coupled multi-domain framework to simulate direct current (DC) arcs, integrating thermal, fluid dynamic, and electromagnetic phenomena. We derive a two-dimensional (2D) axisymmetric model by simplifying the magneto-hydrodynamics (MHD) equations and implement it in MATLAB/Simulink. The model captures the spatiotemporal evolution of temperature, fluid velocity, and magnetic fields within a wall-stabilized arc column. Simulations across a 10 A to 1500 A current range show a pronounced radial temperature gradient, with central axis peaks and rapid peripheral decay. The approach's accuracy is validated by aligning the simulated velocity and magnetic fields with established physical paradigms. Additionally, the model accurately reproduces the inverse current-voltage characteristics observed in classical models and empirical studies, while transient analyses confirm rapid millisecond-scale voltage stabilization. This accessible computational model provides a robust foundation for investigating DC arc dynamics and facilitates system-level simulations for advanced circuit breakers, welding technologies, and plasma applications.

0.39

Real-time virtual circuits for plasma shape control via neural network emulators: experimental demonstration on MAST Upgrade

cs.AI physics.plasm-ph ·2026-08-28 ·Nicola C. Amorisco, Kamran Pentland, Adriano Agnello, George K. Holt, Alasdair Ross +10 more
similarity 0.48
Abstract · submitted

Conventional plasma shape control in tokamaks relies on virtual circuits (VCs) that are computed offline from linearisations around a small, tailored number of reference equilibria, and deployed as expertly prepared schedules during the discharge. Here, we report on the first experimental deployment of real-time VCs. We replace pre-set look up tables with VCs updated in real time using surrogates of the plasma response. Both the existing control architecture and the interpretability of VC-based control are retained. Previous work showed that neural network emulators can produce accurate VCs, and validated their performance in closed-loop shape control simulations. Here, we report their first experimental validation on MAST Upgrade (MAST-U). Dedicated experiments spanning different scenarios, including prescribed shape perturbations, feedback-driven divertor-leg motion, and strongly evolving plasma configurations, show that real-time VCs can realise plasma shape control tasks within the MAST-U plasma control system. These results establish the experimental feasibility of real-time linearisations as a practical extension of conventional plasma shape control in tokamaks. The present implementation demonstrates a central step towards a simpler control workflow, in which manually constructed, phased VC schedules are replaced by VCs generated automatically online from a trained surrogate model, without scenario-specific retraining.

0.40

Real-time virtual circuits for plasma shape control via neural network emulators: integration and testing in the MAST-U PCS

cs.LG physics.plasm-ph ·2026-08-26 ·Matthew J. Marshall, Edward Jones, Graham J. McArdle, Alasdair Ross, Kamran Pentland +8 more
published similarity 0.46
Abstract · 8 pages, 3 figures, presented at 15th Technical Meeting on Control Systems, Data Acquisition, Data Management and Remote Participation in Fu…

The deployment of advanced, AI-enabled control algorithms in tokamak experiments requires robust integration with existing plasma control system (PCS) architectures and extensive pre-experimental validation. In this contribution, we describe the integration and testing of neural-network-emulated virtual circuits for plasma shape control within the MAST Upgrade (MAST-U) PCS environment. The neural network models predict the plasma shape using the plasma current, poloidal field coil currents, and plasma profile parameters. In this paper, we explain how they are deployed via a real-time C++ inference server that interfaces with the PCS, returning the shape prediction and its Jacobian, and how, from the latter, virtual circuit matrices and updated coil current requests are computed for real-time actuation. Emphasis is placed on the validation workflow and best practices adopted to ensure confidence in the proposed control framework prior to experimental deployment. This work demonstrates practical AI-based shape control components for fusion control systems, with direct relevance for upcoming MAST-U experiments and future devices.

0.60

Beyond Tomorrow -- Electrification of Hard-to-Abate Sectors

eess.SY ·2026-09-28 ·Jonas Huber, Johann W. Kolar
similarity 0.42
Abstract · Submitted to IEEE magazine

Reaching net-zero greenhouse-gas (GHG) emissions requires deep electrification beyond ground transportation, buildings, and conventional industry automation. This article discusses direct electrification pathways for hard-to-abate sectors, which today account for 30% of global GHG emissions and include steel, cement, chemicals, aviation, and shipping. Whereas indirect electrification via hydrogen and synthetic fuels will remain indispensable for some applications, direct use of electricity is generally preferable from an efficiency perspective. We review selected emerging opportunities for power electronics in industrial process electrification, including steelmaking through hydrogen plasma smelting reduction or molten-oxide electrolysis, electrified cement production, high-temperature process heat, plasma-assisted chemistry, and electrochemical synthesis. Across these examples, power converters must interface with highly application-specific loads, ranging from low-voltage high-current electrolysis cells to dynamic plasma reactors and megawatt-scale induction heating systems. In addition, high-power grid interfaces and in-plant energy management/buffering solutions must be clarified. Thus, future electrified industrial processes open new "beyond-tomorrow" research challenges for power electronics in close interdisciplinary collaboration with scientists from neighboring disciplines.

0.26

STATCOM-Based Flicker Mitigation in Electric Arc Furnace Systems Using DQ-PI and Lyapunov-Based Nonlinear Control

eess.SY ·2026-10-12 ·Vikram Chekuri, Narapareddy Ramarao, Prashanth N A
unusual similarity 0.39
Abstract · 18 pages, plus a 7-page supplementary document. Compiled with pdfLaTeX

Electric arc furnaces inject stochastic reactive-power swings that cause voltage flicker at the point of common coupling. This paper compares two STATCOM inner controllers for an 11~kV, 50~Hz furnace feeder: a split-frequency DQ-PI design and a Lyapunov-based nonlinear design whose integral state is retained in the storage function, giving global asymptotic stability of the nominal unsaturated current-error subsystem. Gains for both controllers were tuned by a frozen metaheuristic campaign and then evaluated over 600~s with an IEC~61000-4-15 digital flickermeter. A post-campaign audit showed that the stochastic arc realization used for the original comparison was periodic, so the two selected gain sets were frozen without retuning or reselection and evaluated on ten independent stochastic realizations that had been specified and archived before the STO-ENS validation campaign, together with a paired uncompensated case for each realization. Both controllers reduce the mean short-term flicker severity by about 62% relative to the STO-ENS uncompensated baseline, and no statistically detectable difference in mean flicker severity is found between them. They separate instead in realization sensitivity: the Lyapunov standard deviation across arcs is roughly one third that of DQ-PI. Controller ordering inferred from a single stochastic trajectory is therefore not a reliable measure of stochastic robustness, and ensemble validation is necessary.

0.27

AI4Plasma II: Geometry-Aware Surrogate Modeling for Variable Electrode Gap GEC Plasmas

cs.LG physics.plasm-ph ·2026-11-11 ·Hao Yang, Zhenyu Zou, Wenshuai Jie, Luowei Yin, Yufeng Wei +8 more
similarity 0.39
Abstract · 29 pages, 13 figures, 11 tables

Industrial plasma process development requires broad exploration of operating and geometric parameters. Geometric parameters, particularly electrode spacing, affect discharge structure and processing uniformity. Exploring these parameter spaces through repeated high-fidelity simulations can be computationally expensive. Surrogate models can offer rapid predictions, but geometric variation complicates their application because the computational domain and discretization may change across samples. In this work, six geometry-aware surrogate models based on prescribed and learned geometry mappings, extended-domain representation, continuous coordinates, and geometry-native discretizations are compared in terms of their data requirements for accurate predictions of full plasma fields and ion density profiles near the wafer. The simulation dataset spans pressure, voltage, frequency, and electrode gap, with each reference case requiring an average simulation cost of 5.32 CPU h. To achieve a 2% mean error across the four plasma fields, prescribed-mapping Geo-FNO and Transolver require 100 training cases, compared with 250-1000 for the other models. Predicting ion density profiles near the wafer is more demanding and reveals larger differences among models, with prescribed-mapping Geo-FNO requiring the fewest training cases for the profile accuracy targets considered. To further reduce the data required for accurate predictions near the wafer, we introduce charge-separation weighting into the training loss, which reduces the prescribed-mapping Geo-FNO's minimum tested training requirement for a 5% profile error from 1000 to 100 cases. These results support prescribed-mapping Geo-FNO as a practical starting point for the variable-gap problem studied here when a suitable geometry mapping is available, while Transolver achieves the highest prediction accuracy with sufficient training data.

0.40

Reconstruction of Molten Pool Flow Fields from High-Speed Video Using Physics-Informed Neural Networks

eess.IV physics.flu-dyn ·2026-09-26 ·Yue Cao, Qin Su, Dung Hoang Tien, Van Anh Nguyen
unusual similarity 0.38
Abstract

Molten pool flow significantly influences bead geometry, defect formation, and solidification microstructure in wire-arc directed energy deposition (DED). However, direct flow sensing remains an open challenge due to extreme temperatures, intense arc illumination, and complex flow patterns. Traditional research has relied either on computationally intensive fluid dynamics simulations, which require assumed boundary conditions and lack empirical anchoring, or on vision-based tracer particle tracking, which yields sparse, noisy, and physically unconstrained velocity estimates. This work bridges these two paradigms by reconstructing physics-constrained 2D surface flow fields from high-speed imaging of a GTAW-based wire-arc DED process under distinct flow regimes: quasi-steady convection and periodic droplet impact. The pipeline begins with homography correction to calibrate the oblique camera view, followed by dense optical flow extraction to provide raw velocity observations. For quasi-steady pools, a physics-informed neural network (PINN) reconstructs the surface velocity field by jointly enforcing data fidelity, incompressible Navier-Stokes momentum equations, no-penetration boundary conditions, and an arc-forcing prior through composite loss minimization. For pools subject to periodic droplet impact, a phase-conditioned time-dependent PINN is further developed to resolve the cyclic flow evolution throughout the impact period. This work provides a unified framework that bridges high-speed visual sensing and fluid mechanics, enabling physics-grounded flow diagnostics for wire-arc DED processes.

0.29

Reinforcement Learning Controllers for Fusion Scenario Development

cs.LG physics.plasm-ph ·2026-10-19 ·Evgeny Adishchev, Maxim Nurgaliev, Dmitry Sorokin, Alexander Granovsky, Maksim Stokolesov +3 more
similarity 0.38
Abstract

Scenario development, the design of the waveforms that take a tokamak discharge from breakdown to flat-top, is still an iterative, labour-intensive process. Every candidate scenario has to be simulated with a controller in the loop, and the classical shape and current controllers need low-level actuator references. So the process is iterative and includes a number of trial-and-error steps. We propose to replace the per-scenario controller tuning by a single goal-conditioned reinforcement-learning controller trained once, in advance, against a free-boundary equilibrium and transport simulator. A scenario is then specified only by the target waveforms of the physical quantities of interest (plasma current, line-averaged electron density, LCFS shape, x-point positions), and the controller produces the coil-current and fueling commands that realize them. We demonstrate the approach on an EAST plasma-current ramp-up: the controller takes over a small limited plasma, ramps the current and the density, grows the cross-section, forms two x-points and holds a double-null diverted configuration against sampled shape targets for the rest of a 1.2 s episode. The neural network controller is trained using TQC algorithm. On 1024 test scenarios sampled from a low-discrepancy scrambled Sobol sequence in 11-dimensional target space, the controller forms the divertor in 86% of the cases, holds it for more than 0.5 s in 67% and reaches the end of the episode in a diverted state in 58%, with flat-top tracking errors of a few kA in plasma current, $\sim 0.15\times10^{19}$ m$^{-3}$ in density, $\sim 2$ cm in position and $\sim 8$ cm in x-point location; the failures concentrate at the high-current density ($J$) region which is believed to be physically or from engineering perspective not feasible within ohmic mode.

0.13