CS Paper Radar

LocalTrain: Integer-Only Local Learning for Energy-Efficient CNN Training on Edge FPGAs

Shiqi Ding, Xuanyu Liang, Xinyang Liu, Boyang Li, Zhiqiang Que, Guosheng Hu, Jiayang Li

cs.AR cs.LG ·submitted 2026-10-12 16:57 UTC · v1

Abstract

Local learning reduces cross-layer training dependencies, but an efficient accelerator must still retain operands, accumulate gradients, and select quantization scales. We present an FPGA system that trains a CNN and its regional auxiliary classifiers using a shared integer matrix engine. Compact errors are expanded on chip, gradients are folded tile by tile, and historical scales permit direct output conversion. At 200 MHz, the KV260 prototype achieves 76.57% accuracy on CIFAR-10 and 91.85% on SVHN at approximately 4.20 W mean module power. Effective matrix throughput is 31.22 and 31.57 GMAC/s, respectively. Against the same integer method on Jetson Orin Nano, measured training energy is 40.4% and 42.1% lower, with $1.86\times$ and $1.82\times$ longer runtime; measurements use the respective platform power domains. Selected state checks and matching complete-run prediction counts support functional agreement with the software reference.

Comment
7 pages, 2 figures, 5 tables

Closest papers

Nearest neighbours by meaning across the whole index.

ZTA-Q: an Open-source RISC-V Platform for Accurate Quantized CNN Inference

cs.AR ·2026-10-01 ·Yike Li, Ajay Kumar M, Vishnu PS, Dimitrios S. Nikolopoulos, Bo Ji +2 more
publishedcode/data similarity 0.68
Abstract · Accepted for publication at the 2026 IEEE 33rd International Conference on Electronics, Circuits and Systems (ICECS)

Low-precision inference is widely adopted in edge AI to reduce computational cost and memory footprint. However, existing open-source accelerator platforms provide limited end-to-end support for CNNs following the standard TensorFlow Lite integer inference scheme. This paper presents ZTA-Q, an open-source RISC-V-based platform that enables accurate deployment of TensorFlow Lite INT8 models. In addition to extending operator support, ZTA-Q provides a configurable post-processing datapath for studying how circuit-level approximations, including reduced multiplier precision, shared shift scaling, and simplified rounding, affect model accuracy. The proposed system is implemented on a Digilent Arty A7-100T FPGA and operates at 83.3 MHz. Evaluations on representative CNN models show that with LUT, register, and DSP overheads of 26.3%, 12.6%, and 150%, respectively, ZTA-Q limits the degradation in both top-1 and top-5 accuracy to within 0.25 percentage points.

0.35

FAME: An FPGA-Based Platform for Approximate Multipliers Evaluation with Pattern-Guided DNN Retraining

cs.AR cs.LGcs.PF ·2026-09-15 ·Rappy Saha, Nima Amirafshar, Jude Haris, Nima Taherinejad, José Cano
publishedcode/data similarity 0.67
Abstract · Accepted at the 38th IEEE/SBC International Symposium on Computer Architecture and High Performance Computing (SBAC-PAD) 2026

Approximate multipliers can reduce hardware area and energy consumption in Deep Neural Network (DNN) inference; however, they introduce computational errors. Assessing the accuracy of numerous approximate multiplier designs across diverse DNN models and large-scale datasets remains challenging due to prohibitive evaluation times. This overhead primarily stems from the slow emulation of approximate multiplier behavior using look-up tables (LUTs) on CPU and GPU platforms. Moreover, the resulting accuracy degradation must be carefully quantified and, if necessary, mitigated (e.g., through retraining), further increasing the overall evaluation cost. To address these challenges, we propose FAME, an FPGA-based platform for evaluating approximate multipliers. The platform exploits the reconfigurable logic of Field-Programmable Gate Arrays (FPGAs) to implement approximate multipliers directly in hardware, eliminating the need for LUT-based emulation on CPU/GPU platforms and thereby enabling efficient DNN inference while significantly reducing evaluation time on large datasets. Furthermore, we introduce a pattern-guided DNN retraining technique to mitigate accuracy degradation induced by approximate multipliers. Specifically, retraining is guided by multiplier-specific patterns to effectively recover potential accuracy losses. We evaluate FAME using two DNN models, ResNet-18 and MobileNetV2, on the ImageNet dataset across 27 approximate multipliers. During inference, our approach achieves up to a 3.47x speedup in approximate multiplier evaluation compared to prior LUT-based emulation methods. Furthermore, the proposed retraining technique improves accuracy by up to 65.5% over existing retraining approaches for the evaluated multipliers. The code is publicly available at: https://github.com/gicLAB/FAME

0.28

Lonic: Algorithm-Hardware Co-Design for Energy-Efficient Fully Local Online SNN Training with INT4 Precision

cs.AR ·2026-08-12 ·Peilin Chen, Xiaoxuan Yang
publishedcode/data similarity 0.67
Abstract · Accepted to ICCAD 2026

Spiking neural networks (SNNs) have recently attracted increasing attention as an energy-efficient learning paradigm. Existing works also propose temporally and fully local online SNN training algorithms to address memory and computation overhead. However, they do not consider whether the algorithmic advantages can be effectively translated into real-device efficiency. To address this challenge, we present Lonic, an algorithm-hardware co-design for energy-efficient and scalable fully local online supervised SNN learning. On the algorithm side, we implement an INT4 low-precision training algorithm for fully local online SNN learning while maintaining accuracy. On the hardware side, to leverage the benefits of the proposed algorithm, we introduce reconfigurable multiplier-free integer PE arrays, dual-optimization zero-gating strategy, temporal prefix-accelerated local learning dataflow, and low-precision weight movement to significantly improve training efficiency. Compared to Apple M4 and Nvidia V100 GPUs, Lonic achieves average energy efficiency improvements of 17.44x and 66.28x, respectively, along with speedups of 3.25x and 1.02x, respectively. Moreover, Lonic achieves 15.95x (14.64x) and 1.52x (7.28x) energy efficiency (area efficiency) over ASIC TPU-like and H2Learn accelerators, respectively. The code for Lonic is available at https://github.com/peilin-chen/Lonic.

0.47

Adapting DNNs to Embrace Voltage Scaling Induced Errors via Accumulation-Aware Quantization

cs.AR cs.AI ·2026-10-24 ·Alexis Maras, Panagiotis Chaidos, Georgios Alexandris, Dimitrios Soudris, Sotirios Xydis
published similarity 0.65
Abstract · Accepted for publication at the 45rd International Conference on Computer-Aided Design (ICCAD '26), November 08-12, 2026, San Jose, CA, USA

The pervasive deployment of Deep Neural Networks (DNNs) across the computing spectrum has brought growing attention to energy efficiency, alongside raw performance. While voltage scaling is a potent knob for power reduction, its application in next-generation nodes is hampered by severe throughput degradation and susceptibility to process variation. This work aims to address these energy-reliability trade-offs by introducing a hardware-software co-design methodology, based on the observation that timing-robust bit ranges within the accumulator of a systolic array vary significantly across different voltage-frequency operating points. At the software level, we propose an Accumulation-Aware Training approach that incorporates this information as a first-order optimization constraint during training. By integrating mixed-precision quantization with unstructured pruning, we effectively constrain the model's weight distribution to avoid activating the hardware's sensitized high-rank carry chains. At the architectural level, we complement this with selective MSB-masking and fine-grained clock-gating to minimize unnecessary dynamic switching activity. Furthermore, we employ a layer-wise Dynamic Frequency Scaling strategy to further adapt to the accumulator's reduced dynamic range, based on the numerical sensitivity of each layer. We experimentally evaluate the proposed solution on a deep scaled 2nm technology node and demonstrate that, when operating at a low-voltage frontier, our co-optimized post-layout architecture delivers substantial energy and energy-delay product gains of 39% and 23% respectively, relative to the nominal voltage implementation, while maintaining accuracy degradation within 1%.

0.33

16-bit Precision of Convolutional Neural Networks on Microcontroller Units for 8-bit Costs

cs.LG ·2026-10-02 ·Rui Liu, Benjamin Paaßen
similarity 0.65
Abstract

To deploy deep neural networks on edge hardware, highly efficient inference schemes are necessary that retain high accuracy. This work presents W16A16, a high precision (16-bit), fast speed, low energy quantization method. On a widely applied microcontroller architecture Armv7E-M, our proposed approach achieves faster speed and lower energy consumption on layer- and model-level compared to alternative quantization schemes. We analyze the architecture of Armv7E-M, explain the underlying principles behind the performance advantages of 16-bit approaches, and evaluate the empiric quantization errors for regression and classification tasks, as well as empiric time- and energy consumption in MCU deployment. We observe ca.\ 10 times lower quantization errors compared to 8-bit quantization schemes while achieving similar or better inference times and energy consumption.

0.09

ShiftQAT: Quantization-Aware Training for the Numerical Contract of a Fixed-Function Edge CNN Accelerator

cs.LG ·2026-10-15 ·Oguzhan Buyuksolak, Osman Erman Okman, Mehmet Gorkem Ulkar
code/data similarity 0.65
Abstract

Fixed-function CNN accelerators make edge inference fast and energy-efficient, but they execute only networks that obey a precise numerical contract. On the MAX7800x family, this contract requires power-of-two, per-tensor, symmetric scales, 8-bit activations and biases, integer-only arithmetic, and one statically configured shift per layer. We present ShiftQAT, the quantization-aware training (QAT) flow we developed for this family, which produces networks satisfying the contract by construction. It is the default training path of ai8x-training, the family's open-source training toolchain. ShiftQAT resolves residual, concatenation, and weight-sharing dependencies so that activation scales propagate statically and each layer's requantization reduces to one offline-configured shift. It also trains weights and biases on a joint power-of-two grid that fits the 8-bit bias budget. Among the compared methods, only ShiftQAT satisfies all of the contract's scaling constraints, including signed 8-bit activation storage. Even so, on ImageNet it matches the W8A8 accuracy drop of less constrained QAT methods and stays within 2.9 percentage points of FP32 at W4A8. On MAX78002 silicon, ShiftQAT-trained MobileNetV2 and ResNet-18 classify ImageNet images in 14.6 and 8.4 ms at 5.1 and 2.8 mJ per inference.

0.20

Energy-Efficient Visual Inspection with FFT-Based CNNs and Adaptive Floating-Point Quantization

cs.AR ·2026-08-20 ·Lukas Krupp, Marco Groß, Michael Graichen, Kim Ulrich, Norbert Wehn
published similarity 0.65
Abstract · Accepted for presentation at the 23rd International SoC Design Conference (ISOCC 2026). Proceedings to be included in IEEE Xplore

This paper investigates reduced-precision floating-point arithmetic for FFT-based CNN inference on an industrial CPU-FPGA platform. We combine FFT-based convolution with adaptive post-training FP8 quantization and evaluate two FPGA-oriented optimization methods: progressive bias adjustment (PBA) within the FFT and layer-wise exponent-bias selection across the CNN. The methods are implemented in a LeNet-5 accelerator using serial radix-$2^2$ SDF FFT modules and evaluated on an industrial fault detection dataset. Results show that weight scaling outperforms PBA, while layer-wise bias optimization increases the accuracy from 80.33% to 84.13% without modifying the datapath width. Compared with CPU-only inference, the FPGA achieves approximately 2.5$\times$ higher energy efficiency.

0.44

Efficient Reconfigurable Architectures for Deep Learning

cs.AR ·2026-10-31 ·Endri Taka
hot direction similarity 0.64
Abstract · Ph.D. dissertation, Department of Electrical and Computer Engineering, The University of Texas at Austin, 2026

The growing computational demands of deep learning (DL) have driven AI-optimized reconfigurable devices, such as the AMD Versal AI Engines (AIEs), the Intel Stratix 10 NX Tensor Blocks (TBs), and the AMD Ryzen AI NPUs. Their heterogeneous resources and novel dataflow models make efficient exploitation nontrivial, and FPGAs lack native support for structured sparsity. This dissertation optimizes dense general matrix multiplication (GEMM), the dominant DL kernel, on these devices, proposes FPGA architectural enhancements for structured sparsity, and extends the techniques to AMD Ryzen AI NPUs. First, MaxEVA optimizes GEMM on Versal AIEs, achieving up to 2.19$\times$ higher throughput and 20.4% higher energy efficiency than the state of the art. It is then extended to arbitrary matrix sizes, and a systematic framework is proposed for the Stratix 10 NX TBs. Both frameworks reach state-of-the-art int8 throughput of up to 77 and 68 TOPS, and energy efficiency of up to 0.94 and 1.35 TOPS/W, on Versal and Stratix, respectively. Next, Systolic Sparse Tensor slices (SSTs) are proposed as in-fabric hard blocks supporting dense, 2:4, 1:4, and a new 1:3 sparsity level. SST-based GEMM accelerators achieve up to 5$\times$ higher frequency and 10.9$\times$ lower area than conventional FPGA logic, and on sparse ViT and CNN models SSTs deliver up to 3.52$\times$ speedup over dense in-fabric acceleration with up to 13.3% area increase. Finally, a common systematic methodology is proposed to optimize GEMM across the XDNA and XDNA2 AMD NPUs, reaching state-of-the-art performance of up to 6.76 and 38.05 TOPS (int8) and 3.14 and 14.71 TOPS (bf16), respectively.

0.24