CS Paper Radar

Silence Is Not Assurance: When Production Lane Keeping Assist Does Not Warn, and What It Costs

Tianjia Yang, Yuxin Ding, Ke Li, Kaidi Liang, Ruwen Qin, Xianbiao Hu

cs.RO cs.HCeess.SY ·submitted 2026-10-22 20:52 UTC · v1

Abstract

Production lane keeping assist (LKA) systems tell the driver whether they detect the lane markings, but whether this displayed status reflects what the system perceives, and what happens when it does not, has not been examined in real-world driving. This study introduces CANDID-LKA, a CAN-based Diagnosis of the Indicated Detection status in LKA. It evaluates a proprietary driver-facing status using three signals: the displayed status and the steering torque of the driver, both recorded from the controller area network (CAN) bus of the vehicle, and the lane perception confidence of a third-party vision system observing the same road. The framework examines how the status responds to driving conditions and estimates how completely it reports degraded lane perception by comparing it with the other two signals in a latent-class model. We apply it to 39,800 seconds of real-world driving from 13 vehicle models of three manufacturers. The results show that the status does not respond consistently to the conditions that make markings harder to see, and that the three makes differ widely in how often they report not detected. The latent-class model shows that the displayed status is incomplete: it reports only 47% of degraded seconds as not detected, compared with 80% for the third-party low perception confidence, and in half of the low-confidence episodes it never reports not detected. In the silent seconds in which the status reads detected while the perception confidence is low and the driver is not in control, the standard deviation of lateral position over the next 3 s is about 60% larger than when the status and the perception confidence agree. A detected status thus does not guarantee reliable lane perception, and silence with the driver not in control is the case that most needs attention.

Closest papers

Nearest neighbours by meaning across the whole index.

Beyond the Proving Ground: Independent Public-Road Testing of Assisted Lane Change Systems using LiDAR

cs.RO cs.CV ·2026-08-27 ·Marcello Cellina, Akos Kriston, Antonio Migneco, Davide Maggi, Stefano Favelli +5 more
similarity 0.59
Abstract

Testing of commercial Advanced Driver Assistance Systems is essential to ensure safety and compliance during type approval and in service operation. However, proving ground scenarios may not reflect real world driving complexity, while geo fencing can require manufacturer collaboration and limit assessment independence. This work presents a methodology for independently testing Assisted Lane Change systems on public roads. A campaign on the A31 French motorway used a test vehicle equipped with a LiDAR based vehicle detection and tracking system. Tests covered combinations of inter vehicle distance and speed between the test vehicle and the take over vehicle. Real time kinematic global navigation satellite system receivers assessed detection and tracking performance. Recorded lane change trajectories were compared with the lane change suppression requirements of UNECE Regulation Number 79. Of 27 predefined lane change manoeuvres, 18 were completed and 9 suppressed. In 6 cases, the system allowed manoeuvres that did not meet regulatory minimum distance requirements. In 3 cases, the deviation remained statistically significant after accounting for measurement uncertainty. To the authors knowledge, this is the first public road campaign designed to assess Assisted Lane Change compliance with Regulation Number 79 safety distance requirements. The results demonstrate the suitability of LiDAR based sensing for this purpose. The methodology can support market surveillance and future regulatory revisions by revealing real world behaviours not covered by approval procedures.

0.32

Deep Learning-Based Road Lane Quality Assessment from Egocentric Dashcam Video

cs.CV ·2026-10-20 ·Shaif Chowdhury, Akhila Yeruvasu, Moshiur Rahman Tonmoy, Ayush Goyal, Dunren Che
publisheddatasetcode/data similarity 0.58
Abstract · Accepted in the ICECER 2026

Reliable lane markings are important for both human drivers and automated driving systems, but their condition is still commonly assessed through manual inspection. Existing autonomous-driving datasets primarily support lane detection and scene understanding and usually lack maintenance-oriented labels for lane-marking visibility, continuity, or degradation. In this study, we present a geo-referenced smartphone dashcam dataset and baseline framework for lane-marking quality assessment. The dataset contains 63,839 road-facing frames collected across South Texas using a GPS-enabled dashcam application. A subset of 3,339 frames is matched with OpenStreetMap-derived lane-count labels, which are used as weak supervision for lane-count regression and map-consistency evaluation. We propose three lane-quality measures: Contrast Stability Index (CSI), which captures lane-background contrast using Laplacian responses; Line Continuity Ratio (LCR), which estimates structural continuity using edge and Hough-line evidence; and Regression Lane Confidence Score (RLCS), which measures agreement between predicted and map-derived lane counts on matched frames. The baseline prediction models attained strong performance, with CSI (MAE $0.039$, $R^2=0.97$) and LCR (MAE $0.093$, $R^2=0.84$). Notably, CSI and LCR are no-reference, segmentation-derived quality metrics that can be computed without dense human labels. In a pilot validation using 50 human-ranked images, these proposed lane-specific metrics show stronger rank agreement with human lane-quality ordering (e.g., Spearman's $ρ=0.7316$ and Kendall's $τ=0.5472$ for LCR) than general image-quality measures such as PSNR, SSIM, BRISQUE, NIQE, and LPIPS. We believe the dataset, metrics, and baseline provide an initial step toward scalable, low-cost, location-aware lane-marking quality assessment. Data and code: https://github.com/Shaif95/Road_Quality

0.46

Edge Deployable Lightweight Framework for Real-Time Driver Safety System with Integrated Lane Departure and Traffic Sign Recognition

cs.CV ·2026-10-18 ·Hassaan Ali Qureshi, Danish Hussain, Ali Hassan, Aon Safdar, Anas Bin Aqeel +3 more
published similarity 0.54
Abstract

Lane departure and traffic-sign negligence are leading contributors to road accidents, particularly in regions with non-standardized signage and limited annotated data. Existing Advanced Driver Assistance Systems (ADAS) solutions are often developed as disjointed submodules, are rarely validated for real-time operation, and struggle to balance accuracy with low-latency inference for embedded deployment. We address these gaps with a unified, edge-deployable ADAS framework that simultaneously performs lane-departure warning (LDW) and traffic-sign detection and recognition (TSD/TSR), and validate the proposed system on automotive-class devices. Our framework combines a lightweight, lane-segmentation-driven LDW, which includes a drivable-area fallback for degraded markings, with a two-stage TSD/TSR pipeline consisting of efficient sign localization followed by fine-grained classification, designed to preserve accuracy at embedded latency. To support region-specific deployment under data scarcity, we curate a 35-class local traffic-sign dataset and introduce a generalized augmentation and balancing profile, expanding the corpus from 359 images to 8,750 samples. On an NVIDIA Jetson Orin Nano, the integrated system sustains 15 FPS end to end (32 FPS for LDW and 18 FPS for TSD/TSR). The TSD/TSR branch achieves 97.4 mAP for detection and 95.6% validation accuracy (93.1% on a local real-world set) while maintaining an approximately 13.9 M parameter footprint. Relative to recent methods that target a single task or report results only on desktop-class GPUs, our approach delivers both LDW and TSD/TSR with real-time performance on edge hardware, providing a practical pathway to low-cost, field-ready ADAS in resource-constrained settings.

0.24

TriDrive: Joint Driver, Vehicle, and Road Modeling for Forecasting and Driver Monitoring

cs.RO cs.CV ·2026-09-26 ·Yuhang Wang, Jingxin Yang, Chuheng Wei, Yuechen Guo, Jinghan Xu +2 more
benchmarkcode/data similarity 0.54
Abstract · 32 pages (10-page main text plus appendices), 4 figures, 25 tables. Under review. Code, checkpoints, and demo video: https://huggingface.co/…

Predicting how drivers, vehicles, and road scenes interact and evolve together is central to driver monitoring. Prior work models in-cabin activity or traffic-conditioned driver motion in isolation, motivating joint driver, vehicle, and road modeling with real-time on-vehicle evaluation. We introduce TriDrive, to our knowledge the first unified framework that jointly forecasts driver kinematics, vehicle dynamics, and road demands through an automation-conditioned transition model. Modality-specific encoders (an anchored kinematic representation of the driver, causal CAN-bus dynamics, and frozen V-JEPA 2 road latents with structured road margins) are connected by directed residual connections through which driver and road context refine vehicle forecasts. We evaluate TriDrive on three downstream tasks. On the public AIDE benchmark, its kinematic encoder recipe sets a new full-set state of the art (SOTA) among published baselines (48.05 versus 71.47 All-MPJPE). On 197.2 hours of naturalistic BATON subset, directed connections and road margins raise assistance-engaged PR-AUC by 0.084 for steering onset and 0.286 for time-to-collision drops. For real-time use, we distill the road encoders and run TriDrive on a comma four with an external 8 GB GPU, where a lightweight current-state warning probe updates at 5 Hz with 177 ms p95 latency while the joint model forecasts concurrently. The probe is above an openpilot-based baseline on human-labeled manual-driving warnings (AUROC 0.725 versus 0.563), and in a paired on-road study 14 drivers rate its warnings as more appropriate (+1.79) and timely (+2.67) than those of openpilot's driver-monitoring system.

0.32

Speed in the Blind Spot: An Interpretability Analysis of Dynamic Perception in VLMs for Autonomous Driving

cs.CV ·2026-09-29 ·Katharina Winter, Stefan Englmeier, Fabian B. Flohr
similarity 0.54
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

Vision-Language Models are increasingly used in autonomous-driving systems, yet their ability to recover dynamic physical state from visual input remains insufficiently characterized. We study velocity understanding as a controlled diagnostic across three tasks: surrounding-agent speed, current ego speed, and short-horizon future ego-speed proposal. On nuScenes, we evaluate open-weight general-purpose and PhysicalAI VLMs, together with the driving-oriented Alpamayo-1.5 Vision-Language-Action model, using multiple input and output formulations. We combine verbal evaluation with temporal perturbations, counterfactual ego-speed hints and linear probes of hidden representations. The tasks exhibit distinct failure modes. Surrounding-agent speed is weakly encoded in an agent-specific form, whereas current ego speed is often internally accessible but poorly verbalized: continuous probes achieve 4.7-5.8 km/h MAE compared with 10.2-16.8 km/h MAE for verbal outputs. Multiple frames provide inconsistent verbal gains to single frame inputs, and frame order is rarely exploited. Under non-optimized QLoRA, task-specific adaptation improves both task-relevant latent speed representations and verbal readout, but continuous surrounding-agent speed estimation remains weak, while most future-speed gains survive frame shuffling, indicating limited temporal grounding. Driving specialized Alpamayo-1.5 shows stronger latent representations for surrounding-agent and future ego speed, while current ego-speed decodability is comparable and substantial probe-verbal gaps remain. Thus, driving specialization can strengthen motion representations but does not guarantee stronger encoding across both scene and ego states or reliable readout. The results show that plausible planning outputs do not necessarily imply reliable recovery or temporal grounding of the underlying dynamic state.

0.27

Beyond the Leaderboard: Counterfactual Diagnosis of End-to-End and VLA Driving Policies Under Domain Shift

cs.CV cs.AI ·2026-09-18 ·Ruolin Yang, Zilin Huang, Buoyue Wang, Zhengyang Wan, Yuhao Luo +2 more
benchmark similarity 0.53
Abstract

End-to-end and vision-language-action (VLA) driving policies are compared by leaderboard rank, but a rank reports an outcome, not the behaviour behind it, so it predicts poorly how a policy will behave at a new site. On six released policies, rank on nuScenes open-loop error or on NAVSIM's leaderboard does not carry over to scenes with a pedestrian near the ego corridor at a new site. We propose a counterfactual check-up: a few hundred real frames, each edited two ways (pedestrian removed, or re-lit by a night-style perturbation), every edit verified by an independent detector, and the change in the planned trajectory read as a diagnosis rather than a score. From these edits two causal axes are read, and five exams built on them separate what a score merges: how far the policy plans to drive, whether seeing the pedestrian buys safety, whether that response scales with danger, whether the plan moves when nothing requires it, and how much an irrelevant lighting change moves it. On 246 NAVSIM near-pedestrian scenes, in the cells where the pedestrian lies on the planned path only 1.9% of responses are genuine avoidance, and under our open-loop protocol the median clearance change is at most 0.03 m and the median change in planned distance at most 0.08 m for every policy. In a pre-registered test from left- to right-hand drive, the exposure and specificity orderings, the lighting verdict and the collision outcome transfer, while point values and the hazard-sensitivity verdict do not. Read as a selection report, the profiles say which policy is safe because it plans short, which covers a human-like distance without yielding, and which is unsteady under a change that requires no reaction, and they price each verdict: most settle within a few dozen frames, hazard sensitivity needs hundreds. Code and edited frames will be released.

0.40

Towards Systematic Qualification of Vision-Language Models for Automotive Perception Systems

cs.CV cs.SE ·2026-09-22 ·Malsha Ashani Mahawatta Dona, Konstantinos Rokanas, Alexander Säfström, Krishna Ronanki, Christian Berger
published similarity 0.53
Abstract · Accepted in ICTSS 2026 - 38th International Conference on Testing Software and Systems

The field of Artificial Intelligence has been adopted for many application domains. Vision Language Models are one of the recently advanced AI techniques that have been explored to support automotive features such as vehicle perception, and safety assurance. However, such language models are prone to hallucinations, posing a potential threat to the safety of automotive systems that may incorporate them. Within the automotive domain, VLMs could not only hallucinate traffic objects, but could also fail to identify traffic objects that are actually present, which may potentially lead to dangerous situations. Though we have observed a growing body of literature that proposes verification and validation techniques for safe and trustworthy AI, these methods are often studied in isolation, focusing either on run-time or design-time phases. Such isolated techniques could be insufficient in safety-critical, realistic contexts such as automotive perception systems. In this paper, we analyze design-time and run-time verification and validation techniques based on a taxonomy presented by Huang et al. We present an automotive study in which a design-time qualification workflow is proposed to complement run-time monitoring. This workflow combines a fixed safety-relevant ontology-based structured annotation system together with a synonym-based evaluation process to statistically evaluate three state-of-the-art VLMs against data from the nuScenes dataset. We observed that the proposed technique enables deterministic and repeatable quantification of the hallucinations VLMs generate in automotive perception-related tasks. The proposed workflow supports model comparison and deployment-oriented engineering decisions within the design-time verification and validation process and will contribute to a holistic verification strategy that strives towards trustworthy automotive perception systems

0.20

Exploring Mixed-Reality for Enhancing Driver Warning Systems: A Preliminary Study on Attention-Shifting Methods and Hazard Perception

cs.HC ·2026-11-08 ·Shih-Yu Ma, Nolan Robert Brady, Xu Han, Neng-Hao Yu, Tom Yeh
published similarity 0.53
Abstract · 8 pages, 3 figures

Modern vehicles are equipped with advanced sensors and capabilities, yet engaging human drivers effectively in hazard perception remains a challenging research area. This paper investigates the potential of mixed reality (MR) to enhance driver warning systems. The study examines the impact of attention-shifting methods, including visual cues, audio cues, and a combination of both, on drivers' hazard perception. A preliminary study involving six participants was conducted, and the NASA-TLX analysis did not yield significant differences. However, through the use of functional near-infrared spectroscopy (fNIRS), we unveil distinct brain activation patterns associated with visual and sound cues. Further research with larger sample sizes and diverse driving scenarios is required to validate and expand upon these preliminary results.

0.64