CS Paper Radar

Nonlinear Control of Aerial Manipulator

Sandesh Thapa

eess.SY cs.RO ·submitted 2026-10-25 17:20 UTC · v1

Abstract

This paper presents two controllers for a quadrotor equipped with a two-DOF robot manipulator that physically interacts with the environment. Cartesian impedance and adaptive sliding mode controllers are implemented and compared for a simple hovering task in the presence of some bounded disturbance. A full dynamic model is developed, and the two above controllers are implemented with the same initial conditions and desired position.

Comment
5 pages, 9 figures, 2 tables

Closest papers

Nearest neighbours by meaning across the whole index.

Observer-Based Robust Control for an Aerial Manipulator System under Unknown External Disturbances

eess.SY ·2026-09-07 ·Mayank Pandey, Sneha Gajbhiye
similarity 0.72
Abstract

This paper addresses the mathematical modeling and control of an aerial manipulator system comprising a quadrotor as the uncrewed aerial vehicle and a robotic arm as the manipulator. The dynamic model is established by identifying the overall center-of-mass velocity and the system's orientation as constraints, yielding a simplified, two-decoupled subsystems: a locked (overall translation) subsystem and a shape-space (actuation or overall rotation) subsystem, both subjected to external disturbances. Since the system is mechanically coupled, a critical challenge arises where constant bounded disturbances in the first subsystem manifest as time-varying, state-dependent disturbances in the second subsystem. Given that the quadrotor is inherently unstable, the movement of the robotic manipulator (RM) during flight can further jeopardize the stability of the entire QRM system if these disturbances and coupling effects are not effectively managed. To address this, we present a continuous nonlinear disturbance observer-based feedback control law, which enables the independent control of each subsystem while systematically eliminating cross-coupling effects. The efficacy of the proposed controller is validated through multiple simulations emulating practical operating conditions, thereby substantiating its real-world applicability and highlighting the core contributions of this work.

0.11

FAM-DQ: A Dual-Quadrotor-Based Fully Actuated Aerial Manipulator for High-Torque Interaction

cs.RO ·2026-08-13 ·Xuwei Yang, Ruoyu Ren, Ziqian Guo
similarity 0.70
Abstract · 7 pages, 7 figures

Aerial physical interaction requires aerial manipulation platforms to generate large interaction forces and torques while maintaining precise end-effector control. However, conventional underactuated aerial manipulators suffer from strong position-attitude coupling, whereas fully actuated platform designs often face structural complexity, limited payload capacity, and insufficient torque output. This paper presents FAM-DQ, a dual-quadrotor based fully actuated aerial manipulator designed for high-torque physical interaction tasks. By mounting two quadrotor propulsion modules at the ends of a central frame through passive joints, while using a gear-driven servo to regulate the pointing direction, FAM-DQ achieves decoupled $6$-DoF end-effector control with omnidirectional manipulation capability and enhanced torque output. Experiments including trajectory tracking, attitude tracking, static torque measurement, and screw driving validate the proposed design. FAM-DQ achieves a maximum torque of $1.019~\mathrm{N}\cdot\mathrm{m}$ with a total mass of $0.447~\mathrm{kg}$, corresponding to a torque-to-mass ratio of $2.28~\mathrm{N}\cdot\mathrm{m/kg}$.

0.07

A Switched Adaptive Control Framework for Aerial Manipulators Under Dynamic Transitions

cs.RO ·2026-09-21 ·Rishabh Dev Yadav, Saksham Gupta, Amitabh Sharma, Sarthak Mishra, Wei Pan +2 more
top venue similarity 0.69
Abstract

Aerial manipulators represent the forefront of aerial robotics. Although potentially capable of complex interaction tasks, controlling aerial manipulators throughout the dynamic transitions occurring during task execution presents significant challenges. Abrupt or discontinuous changes in system dynamics generated by the transitions suggest the use of a switched approach, yet the available aerial manipulation methods are not designed for coping with switched regimes. In addition, most available methods fall short in coping with the tight couplings between the aerial vehicle and the manipulator, as well as in coping with the state-dependent uncertainties arising from the difficulty in modeling such couplings. We propose a switched-based adaptive control framework for aerial manipulators not relying on a priori knowledge of the vehicle-manipulator couplings and of state-dependent uncertainties. To guarantee stable manipulation despite changes in system dynamics, the framework provides a class of switching signals characterizing those transition phases for which the system is guaranteed to remain stable. Comparative experiments further validate the effectiveness of the proposed switched-based framework over the state of the art.

0.59

Robust Sliding Mode and Admittance Control of Underactuated Aerial Manipulators for Contact-Based Inspection

cs.RO ·2026-08-11 ·Tareq Aziz Alqutami, Yvan Petillot, Matthew W. Dunnigan, Mustafa Suphi Erden
published similarity 0.68
Abstract · 6 pages, 7 figures, submitted to 2026 IEEE Industrial Electronics and Applications Conference (IEACon)

Contact-based industrial inspection requires aerial platforms to maintain stable interaction while rejecting disturbances. Underactuated aerial manipulators present control challenges due to the dynamic coupling between vehicle attitude and force generation. This paper proposes a robust control framework for an underactuated hexarotor equipped with a 1-DoF manipulator to perform sustained contact inspection. The architecture integrates integral-augmented Sliding Mode Control (SMC) for trajectory tracking with an admittance control law for force regulation. The contact force is mapped to a feedforward attitude term, while the 1-DoF arm actively compensates for the tilt to maintain surface alignment. Software-in-the-loop simulations demonstrate that the SMC-based approach achieves superior tracking and coupling rejection compared to traditional PID. Furthermore, the interaction strategy achieved precise force regulation with an RMSE of 0.12N and was able to stably exert up to 20N force, confirming the system's efficacy for stable, reliable contact-based inspection.

0.26

Contact-Aware Incremental Model Predictive Control for an Underactuated Aerial Manipulator

cs.RO ·2026-09-10 ·Darwin Liu, Tamas Keviczky, Sihao Sun
top venue similarity 0.66
Abstract · 8 pages, 6 figures

We present a robust contact-aware control framework for aerial writing on an underactuated platform. The framework combines nonlinear model predictive control (NMPC) for accurate end-effector position and normal-force tracking at small reference penetration depths, with consistent performance across controller tunings, with whole-body incremental nonlinear dynamic inversion (INDI) for robustness to frictional and aerodynamic disturbances during contact. The proposed controllers are validated on a quadrotor-based aerial manipulator with a rigid, single-link, one-degree-of-freedom (DoF) arm in simulation and real-world experiments. The aerial writing experiments span vertical and inclined surfaces, multiple reference forces, different friction conditions, and wind disturbances. The results demonstrate that robust simultaneous five-DoF end-effector pose and contact-force tracking is achievable on a standard underactuated quadrotor with a simple, rigid, single-link arm, without requiring a fully actuated platform, a complex arm, or dedicated force/torque sensing.

0.39

QuadHand: A Compact Quadrotor Aerial Manipulator with MRC-SDF-Based Whole-Body Motion Planning

cs.RO ·2026-09-28 ·Rui Jin, Ruiyang Liu, Xinhang Xu, Haotian Jin, Yi Wang +2 more
highly cited similarity 0.64
Abstract

Uncrewed aerial manipulators (UAMs) integrate robotic arms with aerial platforms for three-dimensional physical interaction. However, enlarging the workspace increases arm-induced disturbances, while existing geometric representations face a trade-off between geometric fidelity and computational efficiency in close-proximity interaction. This paper presents QuadHand, a compact quadrotor aerial manipulator with a 3-DoF arm, gripper, and battery-assisted passive CoG compensation module to reduce dominant arm-induced disturbances. We further propose MRC-SDF, a Multi-articulated Robot-Centric Signed Distance Field that preserves fine geometric detail with tractable computation, and a spatiotemporal whole-body trajectory optimization framework that jointly optimizes the quadrotor and manipulator for safe and executable trajectory generation. Simulations and real-world experiments demonstrate safe and executable aerial manipulation in complex environments.

0.36

Quadrotor Guidance for Tasks along Elliptical Boundary

eess.SY ·2026-10-23 ·Ravi Khandelwal, Ashwini Ratnoo
similarity 0.61
Abstract

This paper presents a guidance method that enables a quadrotor uncrewed aerial vehicle to perform inspection tasks along an elliptical boundary enclosing a structure of interest. The proposed guidance approach leverages a bifurcation theory-based framework that supports multiple inspection tasks, including convergence to a desired viewpoint, switching between viewpoints along the boundary, constant-speed elliptical circumnavigation, and circumnavigation with sectorial dwell-time constraint. Stability analysis of the proposed guidance dynamics establishes convergence of the generated reference trajectories to the desired behavior. The control parameters in the proposed method further allow the settling time of the reference trajectory to be specified for each task. The resulting reference velocity expressions are closed-form and algebraically simple, facilitating practical implementation. A qualitative comparison with existing guidance methods highlights the flexibility of the proposed approach in achieving different inspection tasks through a unified framework, while relying on simpler guidance computations. The proposed guidance method is validated through numerical simulations using a six-degree-of-freedom quadrotor model with model uncertainties, and a cascaded sliding-mode controller that tracks the generated reference trajectories under bounded disturbances.

0.24

AeRSoM: An Aerial Rigid-Soft Integrated Manipulator for Contact-Rich Manipulation

cs.RO ·2026-09-22 ·Jiacheng Liang, Hang Zhong, Yaonan Wang, Ge Chen, Zhixing Zhang +3 more
similarity 0.61
Abstract

Contact-rich aerial manipulation remains fundamentally challenging because interaction forces are directly transmitted to the aerial platform, often leading to instability and degraded task performance. While compliant manipulators can mitigate these effects, existing aerial manipulation systems typically struggle to reconcile interaction compliance with manipulation precision. To this end, this article presents an aerial rigid-soft integrated manipulator (AeRSoM) robot that realizes embodied compliance for aerial manipulation. The proposed system integrates a fully actuated aerial platform, a rigid-soft manipulator, and variable-stiffness regulation to simultaneously achieve stable flight, compliant interaction, and precise manipulation. By distributing compliance throughout the manipulation system, the proposed design leverages distributed embodied compliance to passively absorb contact disturbances while preserving sufficient stiffness for task execution. To fully exploit the mechanical design, a composite control framework is developed for precise end-effector trajectory tracking in the presence of uncertainties and external disturbances. Extensive real-world experiments are conducted in representative contact-rich aerial manipulation tasks, including dynamic transmission-line grasping, physical interaction with a wind turbine blade, peg-in-hole, and screwing operations. The results demonstrate that the proposed rigid-soft integration significantly improves interaction robustness and task adaptability while maintaining manipulation accuracy, highlighting that embodied compliance provides a promising design paradigm for enhancing the safety, robustness, and versatility of aerial manipulation.

0.20