CS Paper Radar

Hardwired Distributed Processing Units at the Sensor: Truly Parallel Vision Pre-Processing that Frees the Host CPU

Raj Mali

cs.DC cs.AReess.IV ·submitted 2026-10-28 19:34 UTC · v1

Abstract

Conventional vision pipelines route every pixel to a host processor, which must then wait for a complete frame before it can act and devote part of each frame period to routine pre-processing. We examine an alternative organisation in which this work is distributed across hardwired distributed processing units (HDPUs): small, fixed datapaths attached directly to the sensor, each committed to a single always-on task, operating truly in parallel on the same pixel stream and delivering compact results to the host. From one library of 3x3 operators sharing a common two-clock latency, we construct three HDPUs (Canny edges, Harris corners, and a line tracker that issues a steering decision) and run them side by side on a single camera stream in a low-cost Artix-7 FPGA, at a cost of 2,568 LUTs and an estimated 0.318 W. Every stage of every unit is bit-exact with its software model. In a full-system simulation with a datasheet camera model, each decision leaves its HDPU within 11.03 camera lines of the pixel that produced it, 22-67x sooner than the earliest moment at which a frame-based program on the host could respond; the HDPU latency varies by no more than 17 ns, whereas the host's own run times reached 12.5x their median. Offloading the three tasks returns 18-30% of a core to the host in every frame period at 640x480, and 63% of the frame period, with all threads in use, at 1080p. The cost of the units grows with frame width only through their line buffers, and in a closed-loop model of a line-following vehicle the HDPU raises the highest speed at which the line is held from 4.75 to 10.00 m/s.

Comment
7 pages, 6 figures, 7 tables. Companion to arXiv:2610.33107

Closest papers

Nearest neighbours by meaning across the whole index.

Fast Path, Exact Path: One Library of Hardwired Operators for Streaming and Exact Canny Edge Detection on a Low-Cost FPGA

cs.AR eess.IV ·2026-10-22 ·Raj Mali
similarity 0.75
Abstract · 7 pages, 5 figures, 7 tables

Hysteresis edge tracking, the final stage of Canny edge detection, follows edge chains of unbounded length and therefore resists single-pass streaming; FPGA designs either approximate it or dedicate separate labelling hardware to it. We show that a single library of hardwired 3x3 operators, each with an identical two-clock latency, delivers both a camera-rate approximation and exact hysteresis on a low-cost Artix-7 (XC7A35T). The fast path streams camera pixels through the operators and K local hysteresis stages and commits each edge decision 262.15-720.63 microseconds after the pixel arrives (K = 1-8; system simulation with a datasheet camera model), that is, 3 + K camera lines later and 46-127x sooner than a frame-based processor can even begin at 30 frames per second. It provably never reports an edge that exact hysteresis rejects, recovers 76.6-96.1% of exact edges at thresholds 20/40, and on the 200 BSDS500 test images retains at least 98.6% of the exact path's boundary F-measure (ODS 0.470-0.477 versus 0.476). The exact path holds 128x128 tiles in block RAM, is exact within each tile, and replaces two-buffer iteration with in-place forward and reverse sweeps built into the same operator. This reduces hysteresis from 38-82 passes to 3-7 on pattern and photo tiles, accelerating the hysteresis step 6.6-21.7x (40x on a worst-case tile) and a complete tile 4.5-9.9x, with identical output. Both paths are bit-exact with software golden models at every pipeline stage and close timing at 50 MHz in at most 1455 LUTs. An optimised multi-core CPU remains faster on stored images, but it cannot begin until the frame is complete.

0.51

Hardwired Distributed Processing Units for Inference: Neural Decisions at the Sensor that Free the Host

cs.AR cs.DCcs.LG ·2026-11-04 ·Raj Mali
similarity 0.74
Abstract · 8 pages, 9 figures, 11 tables. Companion to arXiv:2610.33107 and arXiv:2610.38752

We show that a hardwired distributed processing unit (HDPU) can take a neural decision at the sensor and so remove the inference from the host. Built for zebra-crossing detection on a low-cost Artix-7 FPGA, the unit decides on every camera frame in a fixed 2,269,477 clock cycles (34.04 ms depends upon Fpga clk ), inside the 37.49-ms frame period, and on the board it returns the same scores and decisions as its bit-exact software model on all 639 test images. The whole detection path, from camera pixels to decision, takes 1,814 LUTs, with no processor, no operating system and no full-resolution frame store. When the unit answers instead of reporting "not sure", 95.7% of its answers on street photographs are correct, and a hardware contrast stage lifts accuracy on camera-like dashcam frames from 47.7% to 78.2%. The host is spared all of the inference: 8.13 ms of a core in every frame period, where a full-precision ResNet-18 would need more than a frame period even on 16 threads. It also receives 16 bytes per frame instead of 614,400, 38,400 times less. The unit is an 80x60-pixel pipeline feeding a four-layer binarized CNN with 93,408 one-bit weights, verified bit-exactly from a Python model through RTL simulation to the board. Earlier HDPUs did pre-processing (edges, corners, steering); this one shows that the decision itself can move to the sensor.

0.16

FALCON: FPGA-Accelerated Latency-Certifiable Occupancy Networks for Camera-Based Autonomous Driving

cs.CV ·2026-10-15 ·Haohua Que, Mingkai Liu, Handong Yao
published similarity 0.67
Abstract · Accepted to WACV 2027. 10 pages

A perception system that must brake for a pedestrian does not need a low average latency. It must deliver an answer before the deadline on every frame, the worst case included. Commodity edge accelerators optimize the mean through dynamic scheduling, OS jitter, thermal throttling, and contention, so their per-frame latency can be measured but not bounded. We build FALCON, a camera-based 3D occupancy front-end on the AMD Kria KR260, an embedded FPGA drawing 4.3 W idle and up to 6.6 W under inference, and make the latency guarantee layered and explicit: programmable-logic (PL) compute is cycle-bounded analytically; inference is a measured envelope over 100k-frame traces; and a watchdog enforces output delivery, publishing the previous output flagged stale when a frame is late. The deadline runs use a fixed-work proxy of six ResNet-50 DPU inferences per frame, not the full occupancy network: across three 100k-frame enforced runs, all 300k proxy frames delivered an output within the 100 ms deadline plus at most 10.2 ms, the worst of the three runs. The full six-camera FlashOcc pipeline composes to about 1.3 s per frame on the board and is not yet a 10 Hz system. The two operations the DPU cannot run, a view-transform gather and a bilinear resize, become fixed-trip-count PL IPs numerically matched to their software references. On the full Occ3D-nuScenes validation set the board reaches mIoU 29.88, 92.8% of an FP32 baseline the DPU cannot run. On a ResNet-50 probe over 100k frames the KR260 tail stays within 1.5 times its median (2.0 times for the six-inference proxy), where Jetson Orin reaches 4.4 times and the worst datacenter GPU run (NVIDIA L4) 23.6 times. The deployment recipe, HLS sources, and raw timing traces are released.

0.34

Rethinking Streaming-Perception Evaluation on Heterogeneous Edge Platforms

cs.DC cs.CV ·2026-10-04 ·Misun Yu, Jinyoung Moon, Jemin Lee
published similarity 0.63
Abstract · accepted in ACCV 2026

Multi-camera streaming perception is increasingly deployed on heterogeneous edge platforms shared with co-resident workloads, yet accelerator placement is often evaluated using isolated single-stream experiments and mean streaming average precision (sAP). Using two end-to-end pipelines on a single GPU--NPU platform, we show that isolated evaluation can mis-rank deployment-time placement. Although the GPU pipeline is preferred in isolation, GPU-localized contention introduces deadline misses that make detections stale and can reverse the preferred placement before full GPU saturation. The NPU pipeline is less accurate than the GPU pipeline on small and medium objects in isolation, but nearly matches it on large objects. The largest absolute sAP losses in our latency and contention experiments occur for large objects. In our four-stream experiments, the preferred placement depends on which path becomes stale, and increasing GPU-side contention shifts the best placement from All-GPU to All-NPU. Under a GPU-saturating vision--language co-tenant, All-NPU achieves $5.2\times$ the worst-stream sAP of All-GPU. Because mean sAP can hide severe single-stream degradation, evaluation should report contention sweeps, deadline-miss rates on both paths, and worst-stream sAP alongside mean sAP.

0.29

GPU-resident Execution for Timing-predictable Sensor Processing Systems

cs.DC cs.OS ·2026-10-09 ·Soham Sinha, Rahul Choudhury, Shekhar Dwivedi, Gregory Lee, Gigon Bae +5 more
similarity 0.61
Abstract

Real-time embedded systems increasingly place GPU-accelerated processing of high-bandwidth sensor streams inside closed-loop systems, but the CPU (the host) remains the primary orchestrator of each iteration. The host observes sensor inputs, submits CUDA work, waits for completion, and commits actuation. This host-mediated path exposes the closed-loop end-to-end latency to I/O interrupts, host scheduler decisions, and CUDA API overheads even after common host-side mitigations such as GPU-memory RDMA or CPU core isolation. This paper presents GPU-resident Execution, a new execution model for real-time sensor processing pipelines that keeps I/O and GPU execution in a long-lived device-resident loop. Sensor inputs arrive in GPU memory, trigger GPU-side processing, and reach GPU-visible output endpoints without any host wakeups. We implement the model in the NVIDIA Holoscan C++ framework and provide reference components for building GPU-resident applications. We evaluate our system on NVIDIA GPUs and SoCs with inference, host-contention, multi-loop, and streaming camera workloads. On an industry-grade 1080p, 60 Hz real-time camera-to-display application, GPU-resident Execution reduces photon-to-display jitter from 4.83 ms to 0.66 ms (7.3x) relative to a CPU-driven GPU-memory RDMA baseline and reduces software-processing jitter from 1.70 ms to 0.01 ms (170x).

0.18

Towards Simple Models of Complex SmartNICs

cs.DC cs.NI ·2026-09-25 ·Robert Chang, Teng Jiang, Wonsup Yoon, Daehyeok Kim, Sam Kumar +1 more
similarity 0.59
Abstract

Cloud vendors push ambitious in-network processing (e.g., crypto, telemetry) onto the NIC to offload servers even as link rates climb to terabit speeds. Vendors have responded with heterogeneous SmartNICs. For example, NVIDIA BlueField-3 interposes---between the wire and the host CPUs---a line-rate eSwitch, a multithreaded Data-Path Accelerator, general-purpose ARM cores, and a sea of fixed-function accelerators. These devices are notoriously hard to program, and harder still to predict. Applications can be implemented in many ways, with each choice potentially hitting a different bottleneck. A designer ideally needs to know---cheaply, and before a line of code is written---feasible choices and their bottlenecks, and design patterns to improve performance. Our paper offers a starting point to answer these questions using what we call the ZRAM model. It pairs a platform graph of processing zones and their channels with a program graph of tasks and their traffic fractions. The application designer or a compiler chooses a placement that maps the program graph onto the platform graph. Three metrics computed directly from this mapping---capability, roofline, and capacity---score the placement, deciding its feasibility and naming the bottleneck resource. We use a DDoS detector as a primary case study, and briefly explore two other applications, decision-tree inference and RDMA traversal. We distill seven design patterns for programming SmartNICs including a key one we call sifting. ZRAM generalizes to other SmartNICs such as Intel IPU E2200 and AMD Pensando Salina 400, and opens a new research agenda that includes compilers and hardware design.

0.10

EdgePace: Deadline- and Freshness-Aware LLM Scheduling on Unified-Memory Platforms

cs.PF ·2026-10-27 ·Teng Mei, Chengxuan Pei, Weijun Wang, Jie Wu, Marco Canini +1 more
similarity 0.58
Abstract · 15 pages, including the reference and some interesting finds in a four-page appendix

Large language models (LLMs) increasingly run on edge devices alongside tasks that continuously process sensor data. In many applications, these foreground tasks prepare observations as inputs to the LLM, whose outputs guide subsequent processing or actions. The observations must be processed by foreground deadlines, and LLM feedback must arrive while its source observations remain useful. Yet the CPU and accelerators share a unified-memory system, so LLM inference can delay foreground processing through memory-bandwidth contention even when compute resources remain available. We present EdgePace, a bandwidth-aware runtime that protects foreground deadlines while sustaining timely LLM feedback. EdgePace creates safe suspension points across prefill and decode, monitors foreground memory demand and stalls at low cost, and schedules inference according to contention risk, deadline slack, and output freshness. We evaluate EdgePace on a OnePlus 13 and three NVIDIA Jetson platforms using multi-camera processing and robotic target tracking. Relative to unmanaged inference, it reduces foreground deadline misses by 24.1%--96.1% while retaining 64.9%--98.5% of LLM throughput. All measured LLM outputs arrive within their task-defined freshness windows. On OnePlus 13, for example, camera deadline misses fall by 91.3% while 90.4% of LLM throughput is retained.

0.26

FieldRT: Reconfigurable Architecture from Geometric Sensitivity to Streaming Acceleration

cs.AR cs.PF ·2026-10-31 ·Haichuan Li
similarity 0.57
Abstract

Geometric perception on edge must simultaneously achieve two goals that are rarely addressed together: preserve accurate spatial understanding for object localization and operate within stringent latency, memory, energy, and precision constraints. This coupling is particularly evident in oriented bird's-eye-view (BEV) detection, where global context, multi-scale interactions, and geometric fusion affect both prediction quality and hardware dataflow. Conventional deployment flows first compress a model using aggregate quality or complexity proxies and then map the compressed operations to a fixed accelerator interface. This separation risks removing geometric structures that appear redundant under coarse metrics but are critical for precise localization, while leaving hardware-level efficiencies in the retained geometry unexploited. We present FieldRT, an algorithm-hardware co-design methodology that uses a common analysis of geometric sensitivity and data lifetime to derive both the deployment profile and its spatial realization. We deploy FieldRT with Axis-Fusion Network (AFN), a sub-million-parameter oriented-BEV detector, and construct controlled profiles that vary the capacity and organization of its geometric processing. The experiments show that redundancy is task-dependent rather than uniform across metrics. Dense prediction can improve while real instance detection deteriorates; coarse localization may remain stable while strict-IoU precision degrades. Moreover, transformations that are individually safe can become detrimental when combined. FieldRT translates the retained geometric structure into a parameterized streaming architecture that shares field access and storage across spatial operators. The resulting custom-PL primitives achieve production-scale numerical closure on an AMD Kria KV260 and make otherwise infeasible multi-dilation execution realizable.

0.21