CS Paper Radar

APPlace: Co-Optimizing Device Locations and Access Points for Routing-Aware Analog Placement

Bingyang Liu, Xiaohan Gao, Souradip Poddar, David Z. Pan

cs.AR ·submitted 2026-10-29 07:14 UTC · v1
top venuecode/data

Abstract

Analog layout automation remains challenging in Analog/Mixed-Signal circuit design, because parasitics and mismatches introduced during layout strongly affect circuit performance. Placement is especially critical among the layout stages, as it constrains the routing solution space and the achievable post-layout performance. Existing analytical placement methods optimize device coordinates under center-based wirelength proxies and leave access point (AP) selection to routing. In analog circuits, however, a routing pin is an extended piece of terminal metal rather than a fixed point, and the best AP on it depends on where the other connected devices are placed, so a coordinate-only placement optimizes for connection points that the router will not use. We present APPlace, a routing-aware analog placement framework that co-optimizes device locations and AP selections during global placement, followed by a legalization stage that preserves the structure established by global placement. Experimental results on four real-world analog benchmarks show that APPlace achieves better overall post-layout performance than representative baselines at comparable layout area. Ablation studies further show that removing AP co-optimization causes up to a 13 dB CMRR loss among the OTA benchmarks and a 23% increase in comparator delay.

Comment
Accepted to ASP-DAC 2027. 8 pages, 6 figures, 4 tables. Code: https://github.com/bingyang1132/applace
DOI
10.1145/3840404.3848293

Closest papers

Nearest neighbours by meaning across the whole index.

LAMP: LLM-Driven Analog Placement through Adaptive Tool Composition

cs.AR ·2026-10-29 ·Zecheng Xu, Guanhua Chen, Yumao Wu, Keren Zhu
similarity 0.65
Abstract · 5 pages, 3 figures, 1 table

Analog placement requires circuit-specific trade-offs among area, matching, routability, and electrical performance. Balancing these trade-offs through predefined objectives and fixed placement flows remains difficult. In this paper, we propose an analog placement framework in which a large language model (LLM) acts as a layout engineer through composable placement components. These components support constraint management, placement and legalization, and lightweight evaluation of routability and electrical performance. Using multimodal checkpoints of the initial and evolving design, the LLM selects and combines components to construct and revise its own placement flow. It also adapts the placement hierarchy by reopening modules or partitioning and regrouping devices, allowing local layouts to respond to global design needs. An experience skill provides reusable design knowledge to guide these decisions. Evaluation on two SMIC 180 nm circuits shows that the framework reduces placement area and improves most measured post-layout performance metrics.

0.50

CleanRoute: Reconciling DRC Compliance, Post-Layout Performance, and Runtime in Analog Routing

cs.AR ·2026-11-15 ·Bingyang Liu, Ziming Wei, Xiaohan Gao, Yang Hsu, David Z. Pan
similarity 0.63
Abstract · 8 pages, 6 figures

Automated analog routing remains a long-standing challenge because design-rule checking (DRC) compliance, post-layout performance preservation, and runtime reduction are difficult to achieve together. Existing analog routers have limited coverage of joined-metal design rules, lack control over topology-induced mismatch, and face a trade-off between DRC violations and runtime on uniform routing grids. In this paper, we introduce CleanRoute, an analog router that reconciles these three targets. Hierarchical rule enforcement assigns DRC checks and repairs to stages where the required geometry is complete, covering rules both between separate metal and where metal joins. IR-drop isolation constructs supply trees from current-mirror relationships and device currents to reduce topology-induced mismatch that geometric matching cannot eliminate and voltage drops along high-current paths. A flush-line grid adds net-specific lines aligned with device-metal edges to a coarse routing grid, providing DRC-compliant connections without uniform refinement. Experiments on ten operational transconductance amplifiers (OTAs) in a commercial 40nm process show that CleanRoute produces DRC-clean and functional layouts that pass layout versus schematic (LVS) checking on all benchmarks, with the strongest overall performance preservation and a median routing runtime of 8.82s, whereas the baselines produce no DRC-clean layouts.

0.30

Simulation-Aware In-Context Policy Improvement for LLM-Aided Analog Layout Refinement

cs.AI cs.RO ·2026-08-13 ·Bingyang Liu, Ziming Wei, Xiaohan Gao, David Z. Pan
publishedhighly cited similarity 0.60
Abstract · 7 pages, 3 figures. To appear in the Proceedings of the 2026 International Conference on LLM-Aided Design (ICLAD 2026)

Analog IC layout design remains a labor-intensive iterative process dominated by simulation-driven refinement. Although end-to-end layout generators accelerate initial placement and routing, they still require experts to manually tune layout optimization parameters with repeated post-layout simulations for stringent design specifications. While Bayesian Optimization (BO) is widely adopted for parameter tuning in analog IC design, at the layout level it typically requires hundreds to thousands of evaluations, each involving costly parasitic extraction and post-layout simulation, which makes it impractical. Recently, Large Language Models (LLMs) have demonstrated potential in improving the sample efficiency of such simulation-driven tuning. However, their restricted access to geometric layout context and design-specific heuristics limits their ability to manipulate the layout optimization process. In this paper, we propose a simulation-aware LLM multi-agent framework that performs in-context policy improvement (ICPI) by iteratively updating layout optimization parameters exposed by an analog layout generator through an act-observe-reflect loop on compact structured layout representations. Experiments on real-world analog circuits show that, with only tens of post-layout simulations, our approach improves post-layout performance over the generator's built-in heuristics and BO-based tuning method.

0.61

Budgeted Express-Mesh: Traffic-Aware Link Placement and Deadlock-Free Adaptive Routing

cs.AR cs.NI ·2026-09-15 ·Li Cao, Jingyuan Ma
code/data similarity 0.57
Abstract · 14 pages, 14 figures, 9 tables. Code and artifacts: https://github.com/tsjyma/Express_mesh

We present Budgeted Express-Mesh, a topology-routing co-design that adds a small number of traffic-aware express links under a fixed wire budget. An ASPL-based greedy placement is refined by simulation-guided annealing, while packets use committed top-K routes selected from delayed express-link congestion and reservation signals. Across four synthetic workloads, optimized placements consistently improve high-load throughput over Mesh and random placement, and annealing further improves Greedy. The gains persist under delayed quantized congestion information, longer express-link latency, multi-flit packets, and a 16-by-16 heterogeneous workload.

0.39

E-Layout: Layout-Stage Logic Restructuring via RL-Optimized Equality-Saturated Graph Retrieval-Augmented Generation

cs.AR ·2026-10-19 ·Wenji Fang, Rongjian Liang, Yi-Chen Lu, Cunxi Yu, Chen Chen +5 more
published similarity 0.57
Abstract · Accepted by ICCAD'26

Achieving high sign-off performance in advanced ICs increasingly depends on layout-stage optimization under realistic physical conditions. While recent efforts have moved toward synthesis-layout fusion, most existing works still focus on bringing estimated physical information earlier into synthesis, whose optimization does not fully correlate with real layout-stage behavior. Meanwhile, layout-stage optimization remains largely restricted to a fixed logic structure, relying mainly on buffering and sizing. This fundamentally constrains the optimization space under realistic physical conditions. To address this, we present E-Layout, an ML-driven framework for post-placement layout restructuring. E-Layout jointly optimizes logic transformation and physical implementation across multiple subcircuits under design-level timing feedback. This enables the selection of the most timing-beneficial set of disjoint restructured subcircuits to form the optimized circuit. Specifically, it first constructs equivalence-preserving logic alternatives via e-graph equality saturation, then couples logic selection with physical realization through a graph-based retrieval-augmented generation (RAG) model, and finally refines these local logic-physical decisions with reinforcement learning under design-level timing feedback. Evaluated on 9 diverse designs, it achieves on average 6% TNS improvement and 2% WNS improvement, while even reducing area by 1%, over an industry-leading commercial physical design flow.

0.37

AnalogLayoutWorld: An Open Benchmark for Agentic Analog Layout Design

cs.AI ·2026-11-12 ·NovaSilicon Team
benchmarkcode/data similarity 0.56
Abstract

Coding agents have demonstrated strong capabilities in software development, yet their ability to tackle long-horizon engineering tasks governed by physical constraints remains less understood. We study this question through analog circuit layout, which demands domain knowledge, geometric reasoning, and iterative interaction with design and verification tools. We introduce \textbf{AnalogLayoutWorld}, an open-source agent benchmark with 40 expert-reviewed tasks for end-to-end layout generation from fixed transistor-level netlists. It combines an integrated design environment with independent physical and post-layout electrical verification, as well as objective layout quality metrics co-designed with analog layout experts. Across 13 model--harness configurations, 91.1\% of attempts produce GDS layouts, but only 23.0\% satisfy the benchmark's acceptance criteria. We also evaluate Novara, an internally developed agent system, which achieves the highest reported aggregate score. Our analysis links performance differences to test-time scaling under fixed budgets, suggesting that reasoning efficiency and effective use of verification feedback help sustain design quality as task complexity grows.

0.24

Validity-Preserving Hierarchical RL for Joint Routing and Switch Placement in EDA

cs.LG ·2026-09-30 ·Dorian Gailhard, Ugo Lecerf, Enzo Tartaglione, Donatello Conte, Jhony H. Giraldo
similarity 0.56
Abstract

Routing and switch placement are fundamental combinatorial optimization problems in chip design, requiring the joint optimization of routing topology and physical placement under strict structural, geometric and logical constraints. Existing approaches typically rely on carefully engineered heuristics that incorporate strong problem-specific biases to navigate the enormous space of possible designs. In this work, we introduce a hierarchical reinforcement learning framework for joint routing and switch placement at the level of logical communication routes. Starting from a minimal routing graph, our method progressively constructs increasingly expressive solutions through three coupled operations: switch expansion, switch placement, and route refinement. These operations preserve routing validity by construction, restricting exploration to feasible configurations where every communicating initiator-target pair has one assigned loop-free route. We explore the induced solution space using Gumbel Monte Carlo Tree Search, showing that neural-guided search substantially improves solution quality over non-learning optimization methods. Furthermore, pretraining across floorplans provides a strong initialization for fine-tuning on unseen instances.

0.32

PPAPlace: Differentiable Cross-Stage Objectives for Chip Placement Optimization

cs.LG cs.AIcs.AR ·2026-08-13 ·Ruogu Chen, Jie Han
publishedcode/data similarity 0.55
Abstract · 9 pages, 4 figures, 6 tables, accepted at ICCAD 2026

Macro placement significantly affects a chip's post-route performance, power, and area (PPA). Most placement methods optimize half-perimeter wirelength (HPWL) as the primary objective. However, recent benchmarking shows a near-zero correlation between HPWL and post-route timing metrics such as the worst negative slack (WNS) and total negative slack (TNS). As a result, all six evaluated artificial intelligence (AI) placers degraded PPA relative to the hierarchical baseline. Recent efforts have tried to train cross-stage predictors to close this gap. However, existing methods focus on macro-only representations and use pre-route metrics as training labels. A label fidelity study of ten circuits at four design flow stages reveals that HPWL and pre-route timing poorly reflect final post-route timing rankings. In contrast, post-global-routing achieves the best balance between final timing fidelity and label generation cost-effectiveness. Based on this finding, PPAPlace is a timing-driven differentiable surrogate predicting post-route PPA from macro and standard-cell placements. The surrogate is a dual-stream predictor that combines graph attention over the chip netlist with spatial convolution over the placement grid. It is trained on post-global-routing labels. The predicted WNS and TNS gradients flow end-to-end back to cell coordinates. PPAPlace exploits these gradients in two ways: as a co-objective injected into an analytical placer's optimization loop (PPAPlace-CoOpt), and as a post-placement refinement step that adjusts macro positions via projected gradient descent (PPAPlace-Refine). On five ChiPBench test circuits excluded from training, PPAPlace improves average WNS and TNS by 22\% and 51\% over the hierarchical baseline while preserving power and routability, using the same predictor without test-circuit retraining. Code is available at https://github.com/ValleyC/PPAPlace.

0.53