CS Paper Radar

Hybrid ML for Lightweight Pre-Route Delay Estimation in Open-Source IC Design

Marvin Castro Castro, Erick Carvajal Barboza

cs.LG ·submitted 2026-08-18 15:41 UTC · v1
code/data

Abstract

Static Timing Analysis (STA) is a critical step in the design flow of digital integrated circuits, however, obtaining accurate delay estimations can represent a challenge when limited information regarding physical design is available. In response, this work presents a hybrid and light-weight machine learning (ML) based approach that combines a decision tree with linear regression to improve pre-routing delay estimations generated by the open-source RTL-to-GDSII tool OpenLane. The proposed model achieves an 80\% reduction in error compared to OpenLane's estimates, demonstrates a 71\% improvement even without utilizing OpenLane-specific parameters. Overall, this method offers an alternative to traditional delay propagation techniques and more complex machine learning models that is not only accurate, but is also over 300 times smaller, 2 times faster and offers a higher explainability.

Closest papers

Nearest neighbours by meaning across the whole index.

PPAPlace: Differentiable Cross-Stage Objectives for Chip Placement Optimization

cs.LG cs.AIcs.AR ·2026-08-13 ·Ruogu Chen, Jie Han
publishedcode/data similarity 0.62
Abstract · 9 pages, 4 figures, 6 tables, accepted at ICCAD 2026

Macro placement significantly affects a chip's post-route performance, power, and area (PPA). Most placement methods optimize half-perimeter wirelength (HPWL) as the primary objective. However, recent benchmarking shows a near-zero correlation between HPWL and post-route timing metrics such as the worst negative slack (WNS) and total negative slack (TNS). As a result, all six evaluated artificial intelligence (AI) placers degraded PPA relative to the hierarchical baseline. Recent efforts have tried to train cross-stage predictors to close this gap. However, existing methods focus on macro-only representations and use pre-route metrics as training labels. A label fidelity study of ten circuits at four design flow stages reveals that HPWL and pre-route timing poorly reflect final post-route timing rankings. In contrast, post-global-routing achieves the best balance between final timing fidelity and label generation cost-effectiveness. Based on this finding, PPAPlace is a timing-driven differentiable surrogate predicting post-route PPA from macro and standard-cell placements. The surrogate is a dual-stream predictor that combines graph attention over the chip netlist with spatial convolution over the placement grid. It is trained on post-global-routing labels. The predicted WNS and TNS gradients flow end-to-end back to cell coordinates. PPAPlace exploits these gradients in two ways: as a co-objective injected into an analytical placer's optimization loop (PPAPlace-CoOpt), and as a post-placement refinement step that adjusts macro positions via projected gradient descent (PPAPlace-Refine). On five ChiPBench test circuits excluded from training, PPAPlace improves average WNS and TNS by 22\% and 51\% over the hierarchical baseline while preserving power and routability, using the same predictor without test-circuit retraining. Code is available at https://github.com/ValleyC/PPAPlace.

0.53

Climbing the Design Ladder: Sequential Knowledge Distillation for Early-Stage Circuit Timing Prediction

cs.LG cs.AR ·2026-10-05 ·Reza Moravej, Fahad Rahman Amik, Zhanguang Zhang, Didier Chételat, Yingxue Zhang
similarity 0.56
Abstract

Integrated circuit design involves multiple design stages: logic synthesis, floorplanning, placement, and routing, with each stage taking hours to weeks to complete. Discovering timing violations late in this flow forces costly iterations back to earlier stages, wasting computational resources and delaying product launches. While predicting post-routing timing from early-stage data could prevent these failures, existing machine learning approaches struggle with the massive abstraction gap between post-synthesis logical descriptions and post-routing physical layouts. We propose STEP-KD (Sequential Timing Evaluation via Progressive Knowledge Distillation), which leverages intermediate design stages as ``stepping stones'' for progressive knowledge transfer rather than attempting direct prediction. STEP-KD trains teacher models at the post-routing, post-placement, and post-floorplan stages, then sequentially distills their knowledge to a post-synthesis student model through representation alignment. Experiments on diverse circuits demonstrate that STEP-KD reduces timing prediction error compared to direct distillation and supervised baselines, and in most settings compared to the industry-standard Static Timing Analysis (STA) tool. STEP-KD reduces the weighted mean absolute percentage error of Total Negative Slack prediction to 19.78\%, compared with 74.84\% for STA. Our proposed method is step forward to identify timing problems earlier, avoiding expensive late-stage redesigns.

0.36

LOADBench: A Large Open Analog Dataset and Benchmark for Machine Learning in IC Design

cs.AI ·2026-10-15 ·M. Leibl, F. Azevedo, S. Uhlich, A. Bonetti, A. Venkitaraman +5 more
publishedbenchmarkcode/data similarity 0.54
Abstract · Dataset available on zenodo: https://zenodo.org/records/21759759 9 pages, 6 figures, Conference: MLCAD '26: 8th ACM/IEEE International Sympo…

Machine learning (ML) for analog IC design is constrained by limited open data and the absence of standardized evaluation: results reported in different papers are typically obtained on bespoke, often closed, datasets and with ad-hoc metrics, leaving comparisons across methods unreliable. We address both gaps with a large opensource dataset and a suite of standardized benchmarks. The dataset contains more than 100 operational amplifier (opamp) topologies (1-, 2-, and 3-stage) in the SkyWater130 PDK, each shipped with structural and functional annotations, topology-specific sizing constraints (symmetry and sizing rules), an Ngspice testbench, and a multi-objective NSGA-II sizing run producing around 103 Pareto-optimal and 106 intermediate sizing-performance pairs per topology. On top of this data we define six benchmark tasks with precise protocols: inverse sizing, topology selection, sub-circuit classification, structural circuit generation, Pareto-membership prediction, and multi-objective optimization. Thus, the data presented here constitutes the most comprehensive dataset for ML development in over four decades of analog IC design automation. The dataset, ground-truth annotations, and reference implementations of the metric-defining routines are released under an open license, enabling reproducible and directly comparable evaluation across heterogeneous analog design automation methods.

0.65

Predictable Modelling and Analysis of Software-defined Vehicle Implementations

cs.LO ·2026-09-15 ·Pavlo Tokariev, Yosri Ayari, Julien Deantoni
published similarity 0.53
Abstract

Software-Defined Vehicles (SDVs) rely on middleware-based communication and hardware abstraction mechanisms that introduce temporal uncertainty affecting end-to-end timing guarantees. Previous work proposed probabilistic architectural models for early timing analysis, but the representativeness of these abstractions with respect to SDV implementations remained unclear. This paper presents an experimental framework combining probabilistic design-time timing analysis with a monitored Kuksa-based implementation. The same reaction-time analysis is applied both to simulation and implementation traces, enabling direct comparison between predicted and observed timing behaviour. We additionally introduce a comparison methodology separating conservative coverage from predictive fidelity of timing distributions. The results show that the proposed abstractions remain representative under different middleware load conditions while preserving conservative timing guarantees, supporting incremental timing verification approaches for SDV platforms.

0.34

GRACIDIT: Graph-Circuit Digital Twin for Configuration-Induced Routing Delay Prediction in Zynq UltraScale+ FPGAs

eess.SY cs.ARcs.ETeess.SP ·2026-09-24 ·Mostafa Darvishi
similarity 0.53
Abstract · 25 pages, 7 figures, 3 tables

Configuration-induced perturbations in SRAM-based FPGAs may activate dormant programmable routing branches and increase path delay without immediately producing a functional error. Although prior studies have separately investigated the electrical origin of these delay changes, their in-situ detection, and the topology of commercial routing fabrics, a scalable method for predicting their timing impact at the granularity of programmable interconnect points and routed nets remains unavailable. This paper presents GRACIDIT, a graph-circuit digital twin framework for predicting configuration-induced routing delay degradation in Zynq UltraScale+ FPGAs. The proposed framework extracts the routing-resource graph of the XCZU7EV programmable fabric from the vendor design database, identifies inactive programmable interconnect points adjacent to active routes, and represents each candidate perturbation through its branch topology, geometric span, fan-out, physical region, and downstream loading. These graph features are combined with a calibrated reduced-order electrical model to estimate the delay introduced by single and cumulative routing-branch activations. Controlled configuration-equivalent perturbations are generated on a ZCU104 platform and characterized using complementary routing-domain oscillators and phase-sweep probes. The resulting model associates predicted delay shifts with available timing slack to rank vulnerable programmable interconnect points and routed nets and to construct a spatial vulnerability atlas of the programmable fabric. Experimental evaluation demonstrates a mean absolute prediction error of 7.8 ps, achieves 87.4 percent recall for slack-violating perturbations, and attains a Recall at 10 value of 0.90 for the most vulnerable routing resources.

0.38

Alkaid: A Compiler Framework for Ultra-Low-Latency Kernels on Hardware

cs.AR hep-ex ·2026-10-03 ·Chang Sun, Zhiqiang Que, Dimitrios Danopoulos, Maurizio Pierini, Wayne Luk +1 more
code/data similarity 0.52
Abstract

Ultra-low-latency machine learning and data processing pipelines operating on the sub-microsecond level often contain static dataflow kernels that require fine-grained bitwidth control, arithmetic optimization, and fast hardware performance estimation. This works introduce Alkaid, a free and open source domain specific compiler that translates sub-microsecond latency dataflow kernels into platform agnostic Register Transfer Level (RTL) or High-Level Synthesis (HLS)-ready code in seconds. Alkaid targets ultra-low-latency ML pipelines, especially those addressed by existing ML-to-hardware flows such as \texttt{hls4ml}, while also supporting the surrounding pre-processing, post-processing, and control logic. At its core, Alkaid uses an arithmetic centric intermediate representation, Alkaid Low-level IR (ALIR), to preserve fixed-point semantics, heterogeneous bitwidths, and operation level structure for optimization and code generation. Alkaid further provides comprehensive hardware-aware optimization passes and an interpretable white-box analytical performance model for rapid design space exploration without synthesis in the loop. Across representative ML workloads, including MLPs, GNNs, and transformers, Alkaid achieves 20-30\% lower LUT usage than the best prior flows for bit-exact equivalent designs, with up to 40\% lower latency in some cases. Beyond typical neural networks, Alkaid achieves comparable performance to the state-of-the-art method for synthesizing boosted decision trees, while also enabling the implementation and integration of non-ML kernels such as sorting networks and histograms.

0.56

X-OPM: Explainable Automatic Digital On-Chip Power Modeling for Enhanced Robustness

cs.AR cs.AIcs.LG ·2026-10-06 ·Jingbo Jiang, Xizi Chen, Jian Peng, Wei Zhang
similarity 0.52
Abstract

Proactive power management systems reduce processor dynamic power through runtime power prediction and power-aware scheduling. Accurate, stable and low-overhead digital on-chip power meters (OPMs) are crucial for improving the prediction quality. Recent studies have explored various modeling methods, including using linear models, decision trees, and multi-layer perceptrons (MLPs) to construct OPMs. However, most current approaches train models end-to-end without analyzing the physical interpretability of features, affecting their ability to generalize to unseen workloads. Grounded in the design principles of synchronous digital VLSI circuits, X-OPM introduces a robust feature engineering framework that uses tree-based models to capture feature interactions and linear models for prediction. It also incorporates a human-in-the-loop workflow to balance model accuracy against modeling effort. Evaluated on a commercial C906 vector processor, X-OPM consistently achieves $R^2 > 0.93$ across all workloads with sampling window size set below $8$ cycles. In contrast, state-of-the-art methods including APOLLO, COBIT, and standard MLPs fail to generalize across all test cases. Layout with commercial EDA tools shows that X-OPM incurs an area overhead below $0.1\%$, which is on par with lightweight tree-based and linear models, and significantly smaller than MLP-based models.

0.20

A Surrogate Model for Variation-Aware Clock-Mesh Analysis and Design-Space Exploration using Graph Neural Networks

cs.AR cs.LG ·2026-11-01 ·Muhammad Hadir Khan, Wajid Ali, Arya Thottiparambil Manikandan, Matthew Guthaus
similarity 0.52
Abstract

Clock meshes are widely used in high-performance VLSI systems to minimize skew and tolerate On-Chip Variation (OCV) in nanometer technologies. However, analyzing meshes is difficult because reconvergent paths and multi-source drivers prevent static timing analysis (STA) tools from handling mesh loops, making SPICE the industrial standard. SPICE simulations are accurate but slow, so clock-mesh synthesis relies on approximate models that overlook critical effects such as non-linear buffer driving caused by input slew and input skew. We propose a Graph Neural Network (GNN) based surrogate model of the clock mesh with a new graph representation and a new architecture that predicts power while also improving the delay and slew predictions at the sinks and capturing the skew histogram under OCV. Trained on SPICE data and tested on unseen real designs, our model achieves average errors of $3.40$~ps in delay, $4.14$~ps in slew and $4.46$~ps in skew, compared with $6.28$~ps, $12.35$~ps, and $11.62$~ps for our prior model, and $74.37$~ps delay and $27.51$~ps skew for the approximate method used in current state-of-the-art works. Our model predicts power within $3.4\%$ of SPICE on average, while delivering $18\times$-$1706\times$ speed-ups over the approximate method under OCV modeling, enabling faster and more accurate clock-mesh design-space exploration. A case study on a real design further shows that our surrogate model finds buffering candidates that, at a balanced tradeoff, improves $99^{\text{th}}$-percentile skew by $49.1\%$, reduces power by $25.7\%$, and reduces area by $37.3\%$ at the cost of a $6.8\%$ increase in $99^{\text{th}}$-percentile maximum slew as compared to the state-of-the-art work.

0.21