CS Paper Radar

Force/Torque-Based Kinematic Adaptation for Robotic Manipulation Tasks

Carl Glen Henshaw

cs.RO ·submitted 2026-08-21 19:51 UTC · v1
hot direction

Abstract

Contact-rich robotic manipulation requires an accurate model of the kinematic relationship between a robot's joints and the task features it senses. This relationship is rarely known exactly: it changes with each tool the robot picks up and shifts, sometimes almost instantaneously, as contact modes change --- especially for multi-fingered hands that make and break contact at points that are not exactly prescribed, as in full-hand grasping. This paper develops an adaptive scheme that estimates that relationship online, using only joint-angle sensing and a wrist-mounted force/torque sensor, with no exteroceptive measurement of the tool tip. We derive a provably stable kinematic update law that identifies the kinematics of an unknown tool from force/torque feedback alone, and prove stability of both the rigid case and the case with a compliance controller as an inner loop. We show that identification is confined to the directions the motion excites --- so that, for example, a tool's length is unobservable under a rigid insertion push, while a compliant loop's passive yielding partially excites it; and that with a second-order admittance the compliant certificate holds unconditionally in continuous time. We also pose the combined control and estimation problem as a Quadratic Program (QP): the formulation yields the prediction term of the update law exactly but, instructively, cannot reproduce the tracking adaptation term. We validate the scheme in simulation on a peg-in-hole insertion. This work is the first step in a research program aimed at factoring manipulation learning into a task policy which can be learned in isolation of the robot, for instance by reinforcement learning, and an adaptive kinematic component that adapts online to the particular robot, hand, or tool in use.

Comment
29 pages including appendices, 3 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Control Architecture for Safe Grasping of Fragile Objects Using a Coarse Position-Controlled Gripper

cs.RO ·2026-09-11 ·Marko Pavlic, Moritz Geier, Timo Markert, Darius Burschka
published similarity 0.72
Abstract · Accepted for IEEE IROS 2026 publication

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

0.28

GIFT: Glove-Inferred Force Transfer: Force-Aware Human-to-Robot Skill Transfer from a Wearable Sensing Glove to a Robot Hand Without Tactile Sensors

cs.RO ·2026-09-12 ·Tzach Sarusi
code/data similarity 0.72
Abstract · 7 pages, 5 figures, 1 table. Project page: https://tzahsarusi.github.io

Human-to-robot skill transfer from sensing gloves has so far relied on shared hardware: the same tactile glove worn by the demonstrator and the robot, or a learned alignment between two tactile sensors. We present GIFT (Glove-Inferred Force Transfer), a pipeline in which the interface between human and robot is a physical unit rather than a shared sensor: fingertip force is measured in newtons on the human side and estimated in newtons on the robot side. A wearable glove records finger flexion, calibrated fingertip force, and wrist orientation, while a head-mounted camera records the demonstration; no robot is present. At deployment, the robot estimates force from actuator-current residuals relative to a free-space baseline, through a calibrated mapping to newtons, so any position-controlled hand that reports motor current can serve as the deployment platform. The policy uses a glove-space state and predicts finger-position targets; the robot enters only through two calibrated adapters, a retargeting decoder and a force estimator. We evaluate GIFT on a cup grasp-and-hold task with two action-chunking policies trained on the same demonstrations, with fingertip-force inputs retained in one and zeroed in the other. In a 50-rollout evaluation with sample size and metrics fixed before scoring, both policies succeeded in all 25 rollouts. The median of the per-rollout hold-phase grip-force estimates was 53% lower with force inputs: 1.20 N versus 2.55 N (one-sided Mann-Whitney U, p<0.0001). In an observation ablation, a vision-only policy achieved 0/15 grasps, policies given hand-command state acquired the grasp, and the force inputs determined how hard the policy held. A force channel measured on the human hand thus transfers to a robot hand with no tactile hardware, through a retargeting map from five glove channels to seven robot actuators, with no sensor shared between the two.

0.32

Real-Time Force Regulation for Whole-Hand Dexterous Grasping

cs.RO eess.SY ·2026-09-24 ·Sang Min Kim, Alexander Alexiev, Tzu-Yuan Lin, Sangbae Kim, Young Min Kim +1 more
code/data similarity 0.70
Abstract · 9 pages, 10 figures. Project page: https://sangminkim-99.github.io/reactive-grasp-whole-hand/

Robust dexterous grasping requires maintaining physical stability despite contacts interactively evolving across the entire hand. A precomputed force distribution can easily fail under object motion, modeling errors, or external disturbances. In this paper, we present a framework for real-time force regulation over dynamically changing whole-hand contacts. Our method geometrically estimates contacts across all hand links using a tracked object model and proprioception, without requiring tactile sensing at those contacts. It repeatedly recomputes the desired contact-force distribution subject to friction constraints, actuator limits, and an actuation-consistency constraint motivated by classical whole-limb force analysis. We integrate this force-regulation controller with reactive reaching, enabling the hand to acquire a grasp, maintain it under disturbances, and regrasp after losing the object. Simulation experiments without gravity demonstrate improved grasp retention over fixed-allocation and fingertip-only execution under controlled perturbations, while real-world experiments on a 27-DoF arm-hand system demonstrate grasp maintenance and recovery under human-applied disturbances as contacts evolve across the whole hand. Project page: https://sangminkim-99.github.io/reactive-grasp-whole-hand/

0.39

Tactus: Tactile & Pose Sensing Glove for Natural Dexterity Data Collection

cs.RO cs.AIcs.ARcs.LG ·2026-10-29 ·Li Guan, Rachael Granberry, Sahar Aseeri, Sahar Rostami, Taylor Niehues +99 more
similarity 0.69
Abstract · 9 pages

Collecting naturalistic human manipulation demonstrations with accurate contact force and hand pose is essential for robot dexterous manipulation policy and foundational world model learning - yet no existing wearable platform provides both calibrated fingertip force sensing and occlusion-resilient hand tracking in a form factor that preserves natural manipulation behavior. We present Tactus, a textile-integrated sensing glove that co-optimizes three design pillars: (1) a thin, conformal 3D-knit form factor (1.5 mm fingertip stackup) designed to minimize interference with natural manipulation, (2) strategically placed capacitive tactile sensors at manipulation-relevant regions informed by empirical contact studies, and (3) IMU-fused pose tracking that maintains accuracy through the hand-object occlusions where manipulation data is most valuable. Tactus includes a documented calibration pipeline for cross-glove consistency and per-session calibration for subject-dependent correction. To enable objective comparison, we introduce standardized benchmarking protocols for tactile force regression and hand pose estimation, and apply them to Tactus and two commercially available tactile gloves - to our knowledge the first quantitative cross-platform evaluation of this kind. Tactus resolves a minimum detectable force of 0.59 N at 95% confidence, 1.6 - 2.7x lower than the commercial baselines, and with 0.87 cross-participant consistency, while our pose tracking sustains 11.0 mm fingertip keypoint relative error during manipulation, when occlusion is heaviest. We show that these combined signals support object property estimation, slip detection, and representative recording of hand-object interaction - yielding demonstration data with the fidelity required for contact-aware manipulation policies and world models.

0.21

RUMI: A Robotiq-Matched Universal Manipulation Interface for Robot Learning with Augmented Reality and Haptic Feedback

cs.RO cs.AI ·2026-11-11 ·Kevin Avdiu, Seongjin Bien, Yannik Blei, Philine Meister, Johannes Hechtl +4 more
similarity 0.68
Abstract

Many manipulation tasks require carefully controlled contact forces for successful execution, yet large-scale, force-aware datasets remain scarce. Handheld interfaces can help by transmitting interaction forces directly through the operator's arm, but most existing designs are tailored to simple linear grippers and do not match the nonlinear mechanics of widely used robotic grippers. We present RUMI, a handheld universal manipulation interface matched to the Robotiq 2F-85 with exchangeable fingertip sensors that preserves the target gripper geometry while enabling natural input before contact and force measurement after contact. By integrating the tracking system into a virtual reality headset, our method provides real-time augmented reality feedback about the kinematic feasibility of motion on the target robot platform. We further introduce a haptic feedback mechanism that supports force-aware teleoperation for simulated and real robots. A user study shows fewer episodes containing joint-limit violations with live robot visualization and pose initialization (3/50) than without augmented reality (16/50). We additionally train imitation policies from demonstrations, collected using two different fingertip modalities enabled by the gripper-matched hardware, and assess the haptic interface's capability for collecting force-aware teleoperation datasets in simulation.

0.04

Enabling Scalable Kinesthetic Teaching via Observer-based Hand-guiding with Active Support

cs.RO ·2026-08-11 ·Anna Tuma, Giuseppe Monetti, Jochen J. Steil, Niels Dehio
published similarity 0.68
Abstract

Kinesthetic teaching through robot hand-guiding provides a natural interface for collecting demonstrations in imitation learning and programming-by-demonstration. However, extended sessions cause operator fatigue, reducing demonstration quality and limiting scalability. Current industrial hand-guiding approaches typically provide no active assistance, and alternatives require costly wrist-mounted force-torque sensors or rely on learned motion priors unavailable for new tasks. We propose RHOAS, a hand-guiding scheme that actively supports operator-intended motions using model-based force estimation without additional hardware. Our approach considers robot hand-guiding as an actively controlled interaction by the human operator, rather than an interaction with a passive environment. Standard methods used for hand-guiding typically rely on general passivity-based compliant control architectures that unnecessarily increase operator effort and limit the range of demonstrable motions without providing the intended stability guarantees in active interaction. Instead, our design utilizes model-based external torque estimation, internal joint torque sensing, and redundant robot kinematics to actively support human physical input within the human interaction frequency bandwidth. We address practical challenges of relying on observer-based force estimation, including suppression of unmodeled joint elastic dynamic effects and measurement noise in the feedback path, reduced estimate accuracy close to kinematic singularities, and static gravity compensation errors. In a user study with 16 participants on a KUKA LWR iiwa we demonstrate statistically significant reductions in physical effort, improved maneuverability for both precise and agile tasks, and clear user preference.

0.23

CoPRE: Improving Sensitivity in Proprioceptive Contact Detection for Low-Cost Robot Arms

cs.RO ·2026-09-23 ·Yuxiao Zhu, Jinzhou Li, Yifei Dong, Muhammad Suhail, Chunyuan Yang +4 more
similarity 0.68
Abstract

Contact detection during robotic manipulation allows robots to recognize unexpected contact and adapt their motion accordingly. However, in low-cost robot arms without dedicated force or tactile sensors, detecting weak contacts from proprioception is challenging because the resulting changes in joint-level proprioceptive signals can be small compared to normal variation and noise caused by robot motion itself. We introduce Contact-free Proprioceptive Response Estimation (CoPRE), improving proprioceptive contact detection sensitivity using only contact-free motion, without additional force sensors, contact labels, or analytical dynamics models. CoPRE estimate the expected joint torques under contact-free motion from proprioceptive state history and commanded motion, while removing recent observations that may already reflect contact. It then computes the residual between the expected and observed joint torque estimates, and maps this residual to a contact score using a noise-weighted Jacobian. Real-robot experiments on ARX Arm and Unitree G1 show that CoPRE achieves 74.1% and 82.2% recall on the tested contact trials, compared with 0%/0% on ARX and 16.3%/42.2% on G1 for the learned torque-prediction and inverse-dynamics baselines. CoPRE also reaches 90% detection rate for pushing force at 3.5 N on ARX and 5.5 N on G1. To demonstrate the downstream utility of our method, we implement belief-space manipulation planning for obstacle-aware object placement and book insertion where detected contacts update the spatial belief and enable the robot to retreat from blocked motions, adjust its pose, and retry. Project website at https://copre-arm.github.io

0.35

Compliance for Free: Learning Identifiable Impedance via Bilateral Teleoperation

cs.RO ·2026-09-17 ·Harsha Guda, Adrià Colomé, Carme Torras
similarity 0.67
Abstract

Vision-language-action models tell a robot where to move, but not how hard to push. Contact-rich tasks depend on that second quantity, compliance, yet no widely used demonstration interface records it. The obstacle is identifiability as realized pose and measured force cannot separate the operator's intended equilibrium from their stiffness, so VR controllers, SpaceMouse and handheld grippers cannot supply compliance supervision even in principle. Prior compliance-output policies work around this with hand-specified task structure, privileged simulation contact state, or dedicated force and tactile hardware. Four-channel bilateral teleoperation removes the ambiguity directly by using the leader arm as a separate measurement of the intended equilibrium, making per-axis stiffness identifiable by regression using only the joint-torque sensing already on the manipulator. This yields per-timestep, direction-dependent compliance labels at zero annotation cost, which we use to fine-tune a VLA to emit stiffness alongside pose. On a Franka Research 3 wiping task, ours is the only policy of five whose contact force changes when the instruction asks for a firm wipe rather than a normal one (6.4N (normal) to 9.1N (firm) RMS, Cohen's d = 0.89, p = 0.023

0.22