CS Paper Radar

Artificial intelligence-based predictive fuel blending control for flare gas mitigation

Josip Kir Hromatko, Šandor Ileš, Rube Huljev, Velibor Vučković

eess.SY ·submitted 2026-08-24 14:48 UTC · v1
published

Abstract

This paper describes a fuel blending algorithm based on artificial intelligence and model predictive control. A gas-fired power plant was modeled using physical laws and on-site measurements. A neural network is used to calculate the methane number of the fuel and determine the fuel blending ratio limits so that the methane number is within the limits specified by the engine manufacturer. A model predictive controller adjusts the final blending ratio to meet safety requirements and minimize operating costs. The algorithm was tested in simulations with different scenarios and a reduction in both the operating costs and amount of flaring was observed.

Comment
6 pages, 10 figures
Journal ref
2023 46th MIPRO ICT and Electronics Convention (MIPRO), 2023, pp. 994-999
DOI
10.23919/MIPRO57284.2023.10159741

Closest papers

Nearest neighbours by meaning across the whole index.

Deep Behaviour Cloning of Model Predictive Control for Real-Time Operation of a Hydrogen-Diesel Dual-Fuel Engine

eess.SY ·2026-09-27 ·Alexander Winkler, Neeraj Naduvath Mana, David Gordon, Jakob Andert
similarity 0.54
Abstract · Submitted to Control Engineering Practice

Hydrogen-diesel dual-fuel (H2DF) combustion engines offer a promising pathway for decarbonising hard-to-electrify transport sectors, yet their highly nonlinear dynamics and coupled process variables demand constraint-aware control strategies. Model Predictive Control (MPC) meets these requirements but requires an online optimisation in every combustion cycle, which limits deployment on low-cost embedded hardware. This paper trains a feedforward deep neural network (DNN) by behaviour cloning (BC) to imitate an MPC expert, using 86,000 engine cycles of demonstration data collected at 1500 min-1 on a modified Cummins QSB 4.5-litre hydrogen dual-fuel engine. Two variants, one with process feedback and one without, are validated experimentally. Both track unseen fast-transient load steps (3-8 bar indicated mean effective pressure, IMEP) with normalised root mean square error (NRMSE) values of 7.80% and 9.03% against the expert's 8.01%, while keeping mean NOx and particulate matter emissions at or below those of the expert. Inference takes 2 ms or less on a Raspberry Pi 400 (ARM Cortex-A72 at 2.2 GHz), including 1 ms communication latency, compared to up to 7 ms for the MPC expert, a 3.5x speedup. Open-loop profiling on a low-cost ESP32 microcontroller at 180 MHz gives 4.3 ms per inference, 4x faster than required for the 18 ms cycle window. Beyond the training range the cloned policy saturates its controls but exceeds the pressure-rise-rate limit. To the authors' knowledge, this is the first experimental BC controller for cycle-to-cycle combustion control of an internal combustion engine (ICE), trained from demonstrations recorded on the engine itself.

0.07

Hydrogen-Diesel Dual-Fuel Engine Operation Using Real-Time GRU-Based Nonlinear Model Predictive Control

eess.SY ·2026-09-14 ·Alexander Winkler, Vasu Sharma, Julian Bedei, Edward Sperling, Charles Robert Koch +2 more
similarity 0.52
Abstract · Submitted to International Journal of Hydrogen Energy

Hydrogen-diesel dual-fuel (H2DF) combustion reduces combustion-out CO2 emissions but exhibits nonlinear cycle-to-cycle dynamics at high hydrogen energy shares (HES). This work evaluates nonlinear model predictive control (NMPC) with a gated recurrent-unit deep neural network dynamics model for transient H2DF control. Trained on 99,800 engine cycles, the model predicts indicated mean effective pressure, nitrogen oxides (NOx), particulate matter (PM), and maximum pressure-rise rate. Single-cylinder Cummins 4.5 L experiments follow an unseen 4,900-engine-cycle trajectory. Compared with production diesel-only control, NMPC improves load-tracking mean absolute error by 27.8% and reduces mean PM by 61.1%, while mean engine-out NOx increases by 105.1% without exhaust-gas recirculation. Mean and peak HES reach 39.7% and 55.1%; a high-hydrogen setting achieves 77.8% peak HES without constraint violations. Robust to feedback noise and model-plant mismatch and executing in 3 to 7 ms per engine cycle on low-cost embedded hardware, learned-dynamics NMPC enables practical, real-time, constraint-aware transient H2DF control with substantial diesel substitution.

0.45

Learning Agent-based Model Predictive Control for Holistic Vehicle Performance

cs.RO ·2026-09-10 ·Jiaming Zhong, Reza Valiollahi Mehrizi, Mohammad Pirani, Chao Yu, Alireza Kasaiezadeh +2 more
top venue similarity 0.50
Abstract · 12 pages. Author accepted manuscript

Agent-based model predictive control (AMPC) has recently been proposed as a distributed scheme that collaborates with all agents to achieve optimal holistic performance. However, its optimality highly depends on the prediction accuracy that requires all agents or their contributions to be known, which is too idealistic for actual implementation. This research proposes a novel practical hybrid control scheme - learning agent-based MPC (LAMPC), combining the model-based AMPC approach and data-based learning methods to improve the holistic vehicle performance for multi-agent systems. The Gaussian process regression (GPR) enhanced by an online data management strategy serves as the learning core to predict unknown contributions. A novel multi-step prediction mechanism leverages the GPR learning potential along the horizon. The predicted mean, representing the learned unknown contributions, completes the system model in the MPC for more accurate control. Meanwhile, a stochastic framework is formulated to guarantee control safety and feasibility using soft chance constraints based on the prediction variance. Both simulations and experiments show that, with the learning capability, LAMPC outperforms the traditional AMPC. LAMPC can achieve higher tracking performance in well-learned scenarios and always guarantee constraint satisfaction even in less-learned scenarios. Moreover, the proposed hybrid control scheme is efficient for real-time implementation and is flexible to any control agent topology.

0.66

AI-Powered Flare Combustion Efficiency Estimation

cs.AI cs.CV ·2026-09-10 ·Afeefa Azam, Iyyakutti Iyappan Ganapathi, Fares Ossama Abdelhafez, Divya Velayudhan, Maregu Assefa Habtie +3 more
top venue similarity 0.49
Abstract · Accepted at the 4th International Conference on Machine Learning and Data Engineering (ICMLDE 2025). 5 pages

Achieving high combustion efficiency in flare stacks is crucial for adhering to regulatory standards and controlling the release of hydrocarbons into the environment. Traditional instruments like gas analyzers and hyperspectral cameras are expensive, fragile, and require frequent calibration, which makes them impractical for remote or budget constrained industrial sites. We propose an innovative solution that combines a lightweight vision-language encoder with a compact multi-layer perceptron to predict combustion efficiency directly from low-cost thermal video footage. The fully trained model is integrated into an easy-to-deploy graphical user interface. This interface overlays predicted combustion efficiency values on each video frame, displays real-time trends in combustion efficiency, shows the distribution of combustion efficiency across all frames in the video, and allows users to export CSV reports. Over a six-month period, the system achieved 99% uptime and required less than 15 minutes of maintenance per week.

0.51

AI Control Scientist: LLM-driven Agentic System for Automated Control Design

cs.AI ·2026-08-27 ·Haiteng Wang, Weihao Li, Jing Zhang, Lei Ren
similarity 0.49
Abstract

Control system design is critical for modern industry, such as chemical process temperature regulation and aero-engine control. However,traditional control design workflows rely heavily on expert knowledge and extensive manual parameter tuning, resulting in limited efficiency and scalability. To this end, this paper proposes AI Control Scientist (AICS), the first large language model (LLM)-driven agent capable of automatically generating optimized controller from language design requirements. Specifically, a Task Modeling Agent interprets user requirements to engineering constraints; a Controller Design Agent generate candidate controller structures and executable code; and a Parameter Tuning Agent refine controller parameters under closed-loop performance criteria. Experiments demonstrate that the proposed agentic system can automatically generate multiple representative control systems, outperforms existing automated baselines in both design success rate and optimization efficiency. This work has the potential to transform control system design from human-driven to agent-driven, paving the way for model predictive control and other advanced control systems design.

0.17

Learning to Explain Solutions of Optimal Control Problems

eess.SY ·2026-10-06 ·Jiyong Lee, Ilias Mitrai
similarity 0.48
Abstract

In this paper, we propose an explainable artificial intelligence framework to explain the solution of optimal control problems predicted with graph neural networks (GNNs). The proposed approach first trains a GNN that predicts the solution of the optimal control problem for a given instance represented as a graph. Given the trained GNN, we use explainable AI algorithms to identify variables, constraints, variable-constraint connections, and parameters, i.e., nodes, edges, and features in the graph representation of the optimal control problem, that affect the prediction of the optimal solution the most. We apply the proposed approach to a case study regarding the optimal control of a continuous stirred tank reactor. First, the results show that the GNN model can accurately predict the optimal values of the manipulated variables. Application of explainable AI algorithms reveals equality and inequality constraints that are the most important for predicting the optimal solution. The inequality constraints correspond to ramping constraints, some of which are active at the optimal solution.

0.23

Two-stage Residual Learning for Modelling Strength-Informed Optimisation of Thermal Systems

cs.LG ·2026-10-14 ·Talha Ansar, Waqar Muhammad Ashraf, Abdulelah S. Alshehri, Omar Bayomie
similarity 0.47
Abstract

Aggregate performance metrics do not identify local modelling inaccuracies in machine learning (ML) surrogates used for thermal-system optimisation. This study assesses local modelling strength through validation-based reliability screening and post-optimisation residual assessment. A two-stage residual learning (TSRL) framework, built on artificial neural networks (ANNs), is developed for modelling-strength-informed and domain-constrained optimisation of thermal systems. Within the TSRL framework, a base ANN predicts the process output, and a residual ANN learns the signed residuals left by the base ANN. The TSRL framework is implemented on two case studies of thermal systems, including 817 simulation observations of a crude distillation unit and operating records from a 395 MW industrial gas turbine. The TSRL framework reduces the test root mean square error (RMSE) from 10.3 g/s to 4.7 g/s for Fuel Oil in the refinery dataset and from 151 kJ/kWh to 105 kJ/kWh for turbine heat rate (THR). The base ANNs trained within TSRL are embedded in domain-constrained optimisation problems, and the modelling strength at each computed solution is assessed using the locked residual-score threshold. Each computed solution receives a good modelled region (GMR) or weak modelled region (WMR) label to inform ML model-based decision-making for safety-critical operation of thermal systems.

0.17

CondMSP: Condition-Informed and Resource-Aware Inorganic Materials Synthesis Planning

cs.AI ·2026-10-11 ·Heewoong Noh, Gyoung S. Na, Elton Pan, Namkyeong Lee, Chanyoung Park
similarity 0.47
Abstract

Materials synthesis planning (MSP) connects AI-driven materials discovery to experimental realization by proposing precursors, synthesis operations, and processing conditions for a target material. Existing approaches predict these components separately or in pairs and treat conditions only as a prediction target. Consequently, MSP remains centered on recipe prediction: it leaves unexplored how conditions can serve as process context for constructing synthesis routes, and it does not address which candidate routes should be executed under limited experimental resources. We propose CondMSP, which extends MSP from recipe prediction to execution-aware planning. CondMSP predicts temperature, time, and atmosphere by combining a joint predictor with variable-specific experts, and then uses these predictions both as process context, grounding the generation and retrieval of operation sequences, and as execution requirements, specifying which thermal stages can share a furnace run and at what cost. This specification is held fixed across all compared methods; within it, CondMSP ranks routes across precursor sets by a common utility and, under furnace budgets, jointly selects routes and allocates their thermal stages by constrained optimization. CondMSP improves condition and operation prediction and, under this shared constraint, raises reference-recipe recovery from 27.9% to 32.9% at three simulated furnace runs per target and from 34.7% to 40.0% at 30 trials, while a new evaluation set of 2,344 targets supports generalization beyond oxide-dominated training chemistry.

0.26