CS Paper Radar

A Tendon-Driven Five-Fingered Hand with Distributed Tactile Perception for Dexterous Manipulation

Huayang Chen, Longhui Qin

cs.RO cs.AI ·submitted 2026-08-26 09:01 UTC · v1
published

Abstract

To apply the techniques of embodied artificial intelligence to human-oid robots for complex manipulations, dexterous robotic hands are indispensable, which are restricted by the dexterity and tactile perception capability. In this work, we proposed a novel design of tendon-driven five-fingered hand with dis-tributed tactile perception. With a soft-rigid-hybrid structure employed, both compliance and operational force are endowed to the hand. Dual-modality tactile sensing elements are distributed on the distal and middle phalanges of all five fingers, enabling the simultaneous detection of static contact and dynamic force variations. Manipulation experiments, including counting gestures, finger-to-thumb pinching, object grasping, and bottle-grasp tactile recording, demonstrate the feasibility of the integrated actuation-perception system.

Comment
Accepted by International Conference on Service Robotics (ICoSR) 2026

Closest papers

Nearest neighbours by meaning across the whole index.

A fully articulated humanoid dexterous hand with human-level joint structure enabled by linkage-based actuation

cs.RO ·2026-10-27 ·Jihao Li, Jianguo Wang, Haotian Guo, Yanzhe Wang, Guodong Lu +1 more
similarity 0.67
Abstract

Humanoid dexterous hands are a core component of embodied intelligence, enabling robots to translate high-level intent into rich and adaptive physical interaction. However, existing designs remain constrained by a persistent trade-off among anthropomorphic kinematic complexity, mechanical robustness, load capacity and control simplicity, limiting dexterous manipulation in unstructured environments. Here we present Torch-Hand, a fully articulated humanoid dexterous hand that replicates the joint structure and motion hierarchy of the human hand with 21 degrees of freedom (DOF), comprising a highly articulated five-DOF thumb and four DOF in each of the remaining fingers. The differentiated thumb integrates multi-axis CMC motion to provide broad opposition and flexible contact orientation relative to the four fingers. Unlike tendon-driven or hybrid actuation approaches, Torch-Hand adopts an entirely linkage-based transmission architecture. By integrating screw-linkage actuation, the hand achieves high grasping force and substantial payload capacity while maintaining a compact anthropomorphic form. Its actuation architecture is optimized for control tractability, with all actuators integrated within the palm and arranged in a serial-robot-like configuration that establishes a direct correspondence between motor motion and joint kinematics. This architecture mechanically decouples functional DOF to reduce unintended inter-joint motion propagation, while allowing independently addressable DOF to be actively coordinated into coupled multi-joint motion patterns during complex manipulation. Comprehensive experiments assess reachable workspace, coordinated fingertip trajectories, thumb opposition, 33-grasp taxonomy coverage, grasping force, payload capacity and task-level manipulation. These results establish Torch-Hand as a robust hardware foundation for dexterous embodied manipulation.

0.22

Tactile Sensing Array for Multi-Phalanx Sensing in Humanoid Hands

cs.RO cs.ET ·2026-09-24 ·Neel Adwani, Muhaiminul Islam Akash, Rituja Bhattacharya, Cong Wang
publishedhot direction similarity 0.65
Abstract · Accepted to be presented at IROS Workshop Touch2Action

Humanoid hands require tactile feedback across the whole finger, not just the fingertip, to grasp and manipulate objects properly. Vision and proprioception alone cannot reliably provide this information, particularly when the hand's own fingers occlude the camera's view of the grasp. We present a low-cost tactile array for a humanoid finger, made from Velostat and conductive tape. The fingertip carries seven contact points including a 2x3 matrix wrapped across its front, left, and right faces, and a separate contact point at the tip. The proximal and middle phalanges each carry a single front-facing contact line. We measure the sensor's hysteresis and recovery time after release, through repeated loading and press-release tests. We also test a compliant, 3D-printed contact structure with a gap and a bump, inspired by similar designs in prior work, and show it cuts recovery time by 74% compared to a flush-contact baseline. We then show the sensor can produce distinct activation patterns for different contact geometries (flat, edge, corner) at the fingertip, and that it registers contact across all three phalanges during a grip. Finally, we discuss the limits of our fabrication changes and point to software-based compensation as a promising way to more directly fix the remaining hysteresis in the future.

0.40

Ultra-Low-Impedance Robotic Gripper for High-Bandwidth and Transparent Physical Interaction

cs.RO ·2026-08-10 ·Joon Lee, Ari Choi, Seokhwan Jeong
published similarity 0.65
Abstract · ICRA 2026 (Late Breaking Result Poster)

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

0.19

Beyond Gestures: Estimating Full Hand Pose and Contact Forces from Wrist-Worn Pressure Sensor Array

cs.HC cs.RO ·2026-09-15 ·Svetoslav Kolev, Lingni Ma, Michael Goesele, Renzo De Nardi, Jakob Engel +1 more
hot direction similarity 0.64
Abstract

Capturing hand motion and interaction forces is critical for interactive computing, VR, and high-fidelity tactile demonstrations for robot learning. We introduce a wrist-worn pressure-sensing wristband that recovers continuous full-hand pose and distributed contact force on a single wearable. The system consists of flexible capacitive sensor arrays around the wrist, which require no electrical skin contact, and a recurrent network that maps the resulting pressure signal to hand state. Our key insight is that muscle contraction and tendon displacement produce pressure patterns, which correlate strongly with hand pose and interaction force. To validate this, we collect synchronized recordings of wrist pressure, optical motion-capture hand pose, and tactile-glove interaction force, covering isolated finger motion, fingertip-force stress tests, and natural hand-object manipulation. On isolated single-user motion the wristband attains $4.6^\circ$ mean finger-joint MAE, and across four users manipulating everyday objects it estimates per-finger contact force at $R^2=0.57$, which an external pose signal brings up to $0.75$. We see the wristband as one node in a constellation of everyday wearables -- e.g. paired with an egocentric camera -- adding the contact force that vision cannot observe and taking over when the hand is occluded.

0.44

PHD-Hand: A Printable Humanoid Dexterous Hand with Linkage-Driven 3-DOA Digits

cs.RO cs.AI ·2026-10-21 ·Neel Adwani, Muhaiminul Islam Akash, Saffia Ouali, Ethan Liu, Cong Wang
published similarity 0.64
Abstract · Submitted and Accepted at IEEE-RAS International Conference on Humanoid Robots (Humanoids 2026). 8 pages. Supplementary video: https://lnkd.…

Currently, dexterous humanoid robot hands are widely considered the final hardware bottleneck that hampers generalist robots from physically assisting people at home and work. As conventional tendon-driven designs suffer from high cost, demanding maintenance, poor reliability, and short durability, alternative linkage-driven designs have increasingly gained attention. Despite their potential to avoid the weaknesses of tendon-driven hands, integrating multiple degrees of actuation (DOA) in a single digit with linkage drivetrains is a challenge for design and fabrication. Only a few studies have managed to present functional humanoid hands that are completely linkage-driven and have at least three DOAs per digit without compromising actuator placement and other design preferences. Our work introduces a new linkage-driven hand featuring a unique flexure hinge. Together with elastic drive rods made of spring steel, the linkage drivetrains are significantly simplified. Unlike other linkage-driven designs of similar dexterity, our design does not require many miniature moving parts. As a result, the hand can be fabricated easily with a budget 3D printer. This not only significantly lowers the barrier to entry for using and developing dexterous humanoid robot hand functions, but also allows the hands to be sized much closer to regular human hands. The design offers desirable kinematic advantages as well. A prototype is evaluated for grasping and object manipulation. In addition, this paper presents our latest findings on kinematics and control of the hand.

0.25

SoTa: Soft Tactile Skins for Dexterous Manipulation

cs.RO cs.LG ·2026-10-01 ·Jingyun Yang, Baiyu Shi, Timothy Yu, Haitian Liu, Alberta Longhini +4 more
code/data similarity 0.64
Abstract · The first three authors contributed equally. Project website: https://sota-skin.github.io

A growing body of work suggests that tactile sensing gives robot policies contact information that complements vision in dexterous manipulation. However, visuo-tactile robot data remains scarce: dexterous demonstrations require teleoperating robots, which limits dataset scale. Human demonstrations are far cheaper to collect and offer a path to scale this data, but only if human and robot hands carry tactile sensors with corresponding signals. This requires sensors that conform to different hand geometries, cover the full hand, and share a common layout across embodiments. We present SoTa, a low-cost capacitive tactile skin that provides full-hand coverage on humans and robots while preserving a shared layout of 202 taxels across corresponding finger and palm regions. Our multilayer design with fabric electrodes enables in-house fabrication of thin, soft skins with customizable geometry for under $10 in materials per skin. The sensor retains over 97% of its initial response span after 10,000 loading-unloading cycles with traces retaining continuity through 1,280 tight-fist folding cycles. The shared taxel layout supports human-robot co-training with a common tactile encoder and no learned cross-sensor mapping. Across three contact-rich manipulation tasks, tactile observations improve in-distribution success over vision-only policies. With a fixed robot demonstration budget, adding human demonstrations more than doubles mean success across eight evaluation conditions, from 22.8% to 45.9%, improving success in all five out-of-distribution conditions. We plan to open-source the resources needed to fabricate and operate these skins.

0.20

Tactus: Tactile & Pose Sensing Glove for Natural Dexterity Data Collection

cs.RO cs.AIcs.ARcs.LG ·2026-10-29 ·Li Guan, Rachael Granberry, Sahar Aseeri, Sahar Rostami, Taylor Niehues +99 more
similarity 0.64
Abstract · 9 pages

Collecting naturalistic human manipulation demonstrations with accurate contact force and hand pose is essential for robot dexterous manipulation policy and foundational world model learning - yet no existing wearable platform provides both calibrated fingertip force sensing and occlusion-resilient hand tracking in a form factor that preserves natural manipulation behavior. We present Tactus, a textile-integrated sensing glove that co-optimizes three design pillars: (1) a thin, conformal 3D-knit form factor (1.5 mm fingertip stackup) designed to minimize interference with natural manipulation, (2) strategically placed capacitive tactile sensors at manipulation-relevant regions informed by empirical contact studies, and (3) IMU-fused pose tracking that maintains accuracy through the hand-object occlusions where manipulation data is most valuable. Tactus includes a documented calibration pipeline for cross-glove consistency and per-session calibration for subject-dependent correction. To enable objective comparison, we introduce standardized benchmarking protocols for tactile force regression and hand pose estimation, and apply them to Tactus and two commercially available tactile gloves - to our knowledge the first quantitative cross-platform evaluation of this kind. Tactus resolves a minimum detectable force of 0.59 N at 95% confidence, 1.6 - 2.7x lower than the commercial baselines, and with 0.87 cross-participant consistency, while our pose tracking sustains 11.0 mm fingertip keypoint relative error during manipulation, when occlusion is heaviest. We show that these combined signals support object property estimation, slip detection, and representative recording of hand-object interaction - yielding demonstration data with the fidelity required for contact-aware manipulation policies and world models.

0.21

Tactile Reconstruction of Contact Task Frames and Forces for Hybrid Force/Motion Control

cs.RO ·2026-10-07 ·Antonio Rapuano, Simone Orelli, Barbara Bazzana, Antonio Franchi, Alessandro De Luca
similarity 0.64
Abstract · 14 pages, 9 figures, 7 tables. Video: https://youtube.com/playlist?list=PLejKMZmW8AvI. Dataset: https://doi.org/10.5281/zenodo.23209032

Hybrid force/motion control requires knowledge of the interaction force and of a task frame defining the force- and motion-controlled directions. These quantities are usually obtained from force/torque sensing or model-based residuals, often assuming also a nominal environment model. This work addresses the online estimation of the contact force and a possibly time-varying task frame using only soft optical tactile sensing, under the assumption of locally planar contact with a negligible contact moment. The proposed method maps a single image of the deformed elastomer of a soft optical tactile sensor to observable contact variables: indentation depth, two surface-to-sensor tilt angles, and 3D contact force, each with a per-sample uncertainty estimate. The mapping is learned through a self-labeling acquisition procedure, in which a manipulator imposes controlled contacts while an auxiliary Force/Torque sensor is used offline to provide ground-truth labels. The tactile measurement is then fused with robot proprioceptive data in an Extended Kalman Filter, producing a continuously updated estimate of the contact task frame and of the interaction force. Control experiments with a DigiTac sensor mounted on a UR10 manipulator demonstrate closed-loop contact force regulation against a flat rigid board in linear and angular motion by a human operator, with touch as the only exteroceptive feedback.

0.23