CS Paper Radar

Ultra-Low-Impedance Robotic Gripper for High-Bandwidth and Transparent Physical Interaction

Joon Lee, Ari Choi, Seokhwan Jeong

cs.RO ·submitted 2026-08-10 07:11 UTC · v2
published

Abstract

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

Comment
ICRA 2026 (Late Breaking Result Poster)

Closest papers

Nearest neighbours by meaning across the whole index.

A Quasi-Direct-Drive Underactuated Asymmetric Hand for Dexterous and Efficient Grasping and Manipulation

cs.RO ·2026-09-23 ·Benjamin Davis, Chase Kidder, Hannah S. Stuart
similarity 0.73
Abstract

In this paper, we present the Berkeley QUAD (Quasi-direct-drive, Underactuated, Asymmetric Design) Hand, a four-finger anthropomorphic robotic hand with 11 degrees of freedom and 8 degrees of actuation. The design utilizes QDD actuation at the base of each finger, enabling high force transparency for dexterous, adaptive performance. However, the low torque density of these actuators traditionally presents major issues with size, weight, and thermal limits. We overcome this by applying bio-inspired asymmetry, delegating dexterity to the radial fingers through individual QDD actuation, and strength to the ulnar finger through an underactuated, compliantly coupled transmission driven by a larger QDD motor. A novel preloaded, linkage-based transmission permits this ulnar coupling in a way that preserves human-like workspace reachability. Under light loads, the ulnar motor drives the third (middle) finger directly for dexterity while the fourth (ring) finger mirrors its motion. However, under larger loads, the middle finger complies while the motor drives the ring finger further downwards and inwards toward the center of the grasp to apply better closure forces. Hardware evaluations validate this architecture, demonstrating that the hand achieves 29 out of 33 Feix taxonomy grasps and exhibits backdrive forces as low as 50 g for delicate interactions. Additionally, the underactuated fourth finger improves grasp closure and provides the spatial efficiency necessary for larger actuation, yielding up to a 96-fold reduction in heat generation during sustained loading. Webpage: https://benudavis.github.io/berkeley-quadhand/

0.23

Input-output characterization of robotic grasping: Connecting design parameters to grasp behavior through the admittance

cs.RO eess.SY ·2026-11-12 ·Julien Vanderheyden, Guillaume Drion, Pierre Sacré, Fulvio Forni
similarity 0.68
Abstract

Low-impedance grippers make the dynamics of a grasp matter. Current grasp metrics, however, are static: they describe how a held object resists constant loads, not how it responds to time-varying ones. To quantify this, we rely on small-signal analysis to characterize a grasp by its admittance, the transfer matrix relating load perturbations to object displacements around an equilibrium. This transfer matrix recovers the stiffness and stability of the grasp at zero frequency and captures its natural frequencies and peak gain under time-varying loads. We apply this characterization to a planar two-finger gripper under proportional-derivative control. We show that two grasps of the same object in the same position and with the same contact forces can differ in stiffness by two orders of magnitude. Likewise, two grasps that share the same stiffness can exhibit very different resonances. Nonlinear simulations confirm the effectiveness of our small-signal analysis in capturing the dynamic behavior of grasping.

0.24

Koala Gripper: Co-designing Robotic Grippers and Data-Capture Devices for Scaling Dexterous Manipulation Learning

cs.RO ·2026-08-20 ·Amar Hajj-Ahmad, Zubin Kremer Guha, Tim Fofonoff, Zhi Ern Teoh, Ciarán T. O'Neill +6 more
similarity 0.65
Abstract · Paper website: http://koalagripper.rai-inst.com Paper video: http://www.youtube.com/watch?v=ZoygFCWAVhg

As the demand for larger manipulation datasets grows, handheld robotic gripper data collection and the associated gripper designs become more vital. Current data collection device designs trend towards matching the morphologies of existing robotic grippers, sacrificing ergonomics and manipulation performance. In this paper, we propose a co-design framework that guides the simultaneous development of both data collection and robotic execution devices by weaving both platform constraints into the design process. Through this workflow, we present the Koala Gripper system, a data capture device and robotic gripper platform that improves dexterity and grasp capability compared to parallel jaw grippers while preserving scalability and ease-of-use. The design introduces a novel force-optimized finger/trigger linkage mechanism with directional reflected mass characteristics, a unique monolithic dual-thumb, and user-centered ergonomic design. The design's actuated robotic fingers are backdrivable, with effective mass on the order of tens of grams. We show that these grippers are capable of secure grasps over a wide range of objects, forceful tool use, and precise singulation. We further validate the platform by deploying it with an end-to-end data collection and policy execution pipeline that highlights its capabilities through learning from demonstration. More information available at http://koalagripper.rai-inst.com

0.47

A Tendon-Driven Five-Fingered Hand with Distributed Tactile Perception for Dexterous Manipulation

cs.RO cs.AI ·2026-08-26 ·Huayang Chen, Longhui Qin
published similarity 0.65
Abstract · Accepted by International Conference on Service Robotics (ICoSR) 2026

To apply the techniques of embodied artificial intelligence to human-oid robots for complex manipulations, dexterous robotic hands are indispensable, which are restricted by the dexterity and tactile perception capability. In this work, we proposed a novel design of tendon-driven five-fingered hand with dis-tributed tactile perception. With a soft-rigid-hybrid structure employed, both compliance and operational force are endowed to the hand. Dual-modality tactile sensing elements are distributed on the distal and middle phalanges of all five fingers, enabling the simultaneous detection of static contact and dynamic force variations. Manipulation experiments, including counting gestures, finger-to-thumb pinching, object grasping, and bottle-grasp tactile recording, demonstrate the feasibility of the integrated actuation-perception system.

0.46

PACT: Pose-Robust Actuation Co-Design for Tendon-Driven Robotic Hands

cs.RO ·2026-11-03 ·Prashant Kumar, Rachael Granberry, Taylor Niehues, Andrew A. Stanley, Gabe Pirie
similarity 0.63
Abstract

Humanoid robotic hands must provide sufficient force, speed, and backdrivability within a human-scale envelope. Tendon-driven transmissions address this challenge by relocating actuators to the palm and forearm, but routing paths, moment arms, and capstan dimensions jointly determine both force capability and joint speed, so selecting them sequentially satisfies one requirement at the expense of the other. This paper presents a pose-robust actuation co-design for tendon-driven robot hands (PACT) framework that optimizes tendon routing, moment arms, and capstan dimensions under pose-dependent force requirements and drivetrain-bandwidth constraints. A feasible-force formulation enforces actuator bounds and equilibrium at all joints, while a max-min objective maximizes task-force coverage at the weakest pose. Applied to a four-degree-of-freedom finger, the framework produces an asymmetric N + 1 tendon topology using quasi-direct-drive actuators. Across eight poses, the design achieves task-force coverage of 0.88-1.00 and a predicted 5 Hz minimum isolated-joint flexion/extension bandwidth within a 70th-percentile human-size envelope. Prototype measurements deviate from predictions by up to 24.5%, primarily due to unmodeled transmission losses. These results indicate that co-designing routing with the drivetrain can meet pose-dependent force requirements without relaxing the bandwidth constraint, paving the way for human-sized robotic hands with human-level performance.

0.08

Surgical Master Console Using General-Purpose Robot Arms and a Separable Articulated Distal Interface: Porcine In-Vivo Evaluation

cs.RO ·2026-09-27 ·Minsung Kim, Seonho Shim, Dongho Yee, Younghoon Noh, Juahn Oh +7 more
similarity 0.63
Abstract · Submitted to IEEE ICRA 2027

High-performance surgical master consoles offer intuitive articulated manipulation but are expensive and difficult to reproduce, while accessible commercial haptic devices lack built-in interfaces for surgical wrist articulation and continuous grasp. We present a laparoscopic master in which general-purpose robot manipulators provide the programmable base and surgical-specific interaction is concentrated in a separable distal adapter. Each 6-DoF arm carries a custom 2-DoF direct-drive wrist, continuous grasp sensing, and clutch-based workspace management; the complete bimanual hardware costs approximately US$5,500, below common bimanual commercial haptic references. To support sustained hand-guided use, we characterize current scaling, gravity, and break-away friction and use them for posture-dependent gravity compensation and motion-gated assistance, reducing continuous actuation and thermal loading. A common master state drives either Isaac Sim or an RCM-constrained dual-FR3 platform. Master-state publication to FR3 target update adds at most 8 ms, and tip tracking shows 0.31-0.66 mm mean delay-aligned residuals. In a porcine cholecystectomy experiment, five common operator-side metrics and hand/tip-speed distributions were compared descriptively with human in-vivo telemetry from 120 clinical Versius recordings of 99 cholecystectomy procedures; no interruption originated from the master console, and no abnormal clinical signs were recorded during the 7-day postoperative observation period. These results demonstrate a surgical master built from general-purpose robot arms with surgical-specific interaction concentrated in a separable distal interface.

0.32

TinyARM-X: A Series of Open-Source, Configurable, and Transparent Torque-Controlled Desktop-Scale Robotic Manipulators

cs.RO ·2026-11-18 ·Nicolas Kosanovic, Jean Chagas Vaz
similarity 0.63
Abstract · 9 pages, 5 figures. Submitted to a robotics Journal. Reviews have not come in yet

Visuomotor policies have demonstrated that imprecise low-cost robots can autonomously complete complex manipulation tasks. However, most inexpensive manipulators rely on compact and rigidly position-controlled servos for actuation, which complicate simulation, operation, and safety. This work introduces TinyARM-X, a framework for easily manufacturable, configurable, and torque-controllable low-cost (<350 USD) serial manipulators. By using a single hardware/software architecture, a <7 Degree of Freedom (DoF) TinyARM can be manually reconfigured to an operational >3 DoF robot within 10 min. Actuator modeling and dynamic compensation enable torque-controlled applications like mixed-reality impedance control teleoperation and simulator force feedback rendering. Experiments include mechanical benchmarking and real-world force-aware telemanipulation. The TinyARM-7 has a payload of 33.5 g, a max speed of 0.77 m/s, and a reach of 210 mm. Moreover, with dynamic compensation, the robot has a backdrive-breakaway force of 1.4 N and a backdrive-running force of 0.7 N. Additionally, Cartesian-Impedance Control (CIC) attains a translational stiffness of >15 N/m. Lastly, the TinyARM-X stack is open-sourced to disseminate accessible desktop-scale torque-controlled robotic manipulation to the community.

0.22

DNPush: Distributed Nonparallel Pushing Force Control of Multi-Robot Systems for Object Transportation

cs.RO eess.SY ·2026-10-03 ·Duy Anh Nguyen, Pham Duy Hung, Trung Dung Ngo
similarity 0.62
Abstract · 8 pages, 8 figures. Submitted to IEEE Robotics and Automation Letters

This letter proposes DNPush, a Distributed Nonparallel Pushing force controller for cooperative object transport without inter-robot communication. Each robot uses local force measurements, a preassigned force weight, and a locally expressed desired transport direction, without requiring an object model, contact locations, a CoM estimate, or moment arm magnitudes online. DNPush regulates nonparallel force magnitudes from local force direction misalignments through a reciprocal-sine law. Under the stated contact conditions, Lyapunov analysis with LaSalle's invariance principle proves convergence to a unique rotational equilibrium, where perpendicular force contributions cancel and the net torque from normal forces is zero. Object velocity converges to the desired transport direction, and suitable contact regions exist for convex polygons. Simulations isolate the reciprocal-sine scaling mechanism, five-robot coordination, and active rotational damping. Hardware experiments with soft tactile differential-drive robots achieve a velocity direction error of 0.61 deg +/- 0.79 deg over five trials with a fixed transport direction and demonstrate object transport through waypoints with three robots.

0.29