CS Paper Radar

Input-output characterization of robotic grasping: Connecting design parameters to grasp behavior through the admittance

Julien Vanderheyden, Guillaume Drion, Pierre Sacré, Fulvio Forni

cs.RO eess.SY ·submitted 2026-11-12 09:07 UTC · v1

Abstract

Low-impedance grippers make the dynamics of a grasp matter. Current grasp metrics, however, are static: they describe how a held object resists constant loads, not how it responds to time-varying ones. To quantify this, we rely on small-signal analysis to characterize a grasp by its admittance, the transfer matrix relating load perturbations to object displacements around an equilibrium. This transfer matrix recovers the stiffness and stability of the grasp at zero frequency and captures its natural frequencies and peak gain under time-varying loads. We apply this characterization to a planar two-finger gripper under proportional-derivative control. We show that two grasps of the same object in the same position and with the same contact forces can differ in stiffness by two orders of magnitude. Likewise, two grasps that share the same stiffness can exhibit very different resonances. Nonlinear simulations confirm the effectiveness of our small-signal analysis in capturing the dynamic behavior of grasping.

Closest papers

Nearest neighbours by meaning across the whole index.

Ultra-Low-Impedance Robotic Gripper for High-Bandwidth and Transparent Physical Interaction

cs.RO ·2026-08-10 ·Joon Lee, Ari Choi, Seokhwan Jeong
published similarity 0.68
Abstract · ICRA 2026 (Late Breaking Result Poster)

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

0.19

How Firm Should a Grasp Be?

cs.RO cs.CV ·2026-10-08 ·Matthew Beveridge, Shree K. Nayar
dataset similarity 0.63
Abstract · CoRL 2026

An ideal robot grasp is firm enough to securely handle an object, yet gentle enough to avoid damaging it. Achieving this balance requires knowledge of the object's material properties, such as its mass, elasticity, and surface friction. These properties, however, are seldom precisely known a priori. In this work, we propose a visuotactile approach to estimating material properties in real time, during the process of grasping. Our method uses these estimated properties to determine the minimum grasp force required to handle the object. We contribute a new dataset of real-world objects (fruits and vegetables) with measured physical properties (shape, mass, elasticity, and friction), which we use to construct our force estimation model via simulations. We experimentally validate our approach to grasp force control using a robot with a parallel-jaw gripper. We demonstrate our system's ability to gently grasp a wide variety of objects, in each case adapting to their unique physical properties.

0.11

Real-Time Force Regulation for Whole-Hand Dexterous Grasping

cs.RO eess.SY ·2026-09-24 ·Sang Min Kim, Alexander Alexiev, Tzu-Yuan Lin, Sangbae Kim, Young Min Kim +1 more
code/data similarity 0.63
Abstract · 9 pages, 10 figures. Project page: https://sangminkim-99.github.io/reactive-grasp-whole-hand/

Robust dexterous grasping requires maintaining physical stability despite contacts interactively evolving across the entire hand. A precomputed force distribution can easily fail under object motion, modeling errors, or external disturbances. In this paper, we present a framework for real-time force regulation over dynamically changing whole-hand contacts. Our method geometrically estimates contacts across all hand links using a tracked object model and proprioception, without requiring tactile sensing at those contacts. It repeatedly recomputes the desired contact-force distribution subject to friction constraints, actuator limits, and an actuation-consistency constraint motivated by classical whole-limb force analysis. We integrate this force-regulation controller with reactive reaching, enabling the hand to acquire a grasp, maintain it under disturbances, and regrasp after losing the object. Simulation experiments without gravity demonstrate improved grasp retention over fixed-allocation and fingertip-only execution under controlled perturbations, while real-world experiments on a 27-DoF arm-hand system demonstrate grasp maintenance and recovery under human-applied disturbances as contacts evolve across the whole hand. Project page: https://sangminkim-99.github.io/reactive-grasp-whole-hand/

0.39

Control Architecture for Safe Grasping of Fragile Objects Using a Coarse Position-Controlled Gripper

cs.RO ·2026-09-11 ·Marko Pavlic, Moritz Geier, Timo Markert, Darius Burschka
published similarity 0.62
Abstract · Accepted for IEEE IROS 2026 publication

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

0.28

Quasi-static analysis of passive stability in a novel underactuated multi-finger hand

cs.RO ·2026-09-10 ·Léonie Plancoulaine, Sylvain Guégan, Franck Plestan, Damien Chablat
published similarity 0.61
Abstract

Underactuated robotic hands achieve adaptive and robust grasping with a reduced number of actuators, but predicting the stable equilibrium pose of the grasped object remains a significant challenge. This paper introduces a quasi-static analytical approach to assess passive stability in underactuated multi-finger hands. A novel three-finger hand architecture integrating a differential spring-loaded slider mechanism is introduced, enabling versatile and adaptive grasping. The study focuses on how the differential mechanism influences the overall grasp behavior and analyzes the effect of object size on the stable equilibrium configurations for two canonical grasp types: cylindrical and spherical.

0.30

Force/Torque-Based Kinematic Adaptation for Robotic Manipulation Tasks

cs.RO ·2026-08-21 ·Carl Glen Henshaw
hot direction similarity 0.60
Abstract · 29 pages including appendices, 3 figures

Contact-rich robotic manipulation requires an accurate model of the kinematic relationship between a robot's joints and the task features it senses. This relationship is rarely known exactly: it changes with each tool the robot picks up and shifts, sometimes almost instantaneously, as contact modes change --- especially for multi-fingered hands that make and break contact at points that are not exactly prescribed, as in full-hand grasping. This paper develops an adaptive scheme that estimates that relationship online, using only joint-angle sensing and a wrist-mounted force/torque sensor, with no exteroceptive measurement of the tool tip. We derive a provably stable kinematic update law that identifies the kinematics of an unknown tool from force/torque feedback alone, and prove stability of both the rigid case and the case with a compliance controller as an inner loop. We show that identification is confined to the directions the motion excites --- so that, for example, a tool's length is unobservable under a rigid insertion push, while a compliant loop's passive yielding partially excites it; and that with a second-order admittance the compliant certificate holds unconditionally in continuous time. We also pose the combined control and estimation problem as a Quadratic Program (QP): the formulation yields the prediction term of the update law exactly but, instructively, cannot reproduce the tracking adaptation term. We validate the scheme in simulation on a peg-in-hole insertion. This work is the first step in a research program aimed at factoring manipulation learning into a task policy which can be learned in isolation of the robot, for instance by reinforcement learning, and an adaptive kinematic component that adapts online to the particular robot, hand, or tool in use.

0.29

Koala Gripper: Co-designing Robotic Grippers and Data-Capture Devices for Scaling Dexterous Manipulation Learning

cs.RO ·2026-08-20 ·Amar Hajj-Ahmad, Zubin Kremer Guha, Tim Fofonoff, Zhi Ern Teoh, Ciarán T. O'Neill +6 more
similarity 0.60
Abstract · Paper website: http://koalagripper.rai-inst.com Paper video: http://www.youtube.com/watch?v=ZoygFCWAVhg

As the demand for larger manipulation datasets grows, handheld robotic gripper data collection and the associated gripper designs become more vital. Current data collection device designs trend towards matching the morphologies of existing robotic grippers, sacrificing ergonomics and manipulation performance. In this paper, we propose a co-design framework that guides the simultaneous development of both data collection and robotic execution devices by weaving both platform constraints into the design process. Through this workflow, we present the Koala Gripper system, a data capture device and robotic gripper platform that improves dexterity and grasp capability compared to parallel jaw grippers while preserving scalability and ease-of-use. The design introduces a novel force-optimized finger/trigger linkage mechanism with directional reflected mass characteristics, a unique monolithic dual-thumb, and user-centered ergonomic design. The design's actuated robotic fingers are backdrivable, with effective mass on the order of tens of grams. We show that these grippers are capable of secure grasps over a wide range of objects, forceful tool use, and precise singulation. We further validate the platform by deploying it with an end-to-end data collection and policy execution pipeline that highlights its capabilities through learning from demonstration. More information available at http://koalagripper.rai-inst.com

0.47

Active Surface-Driven Reconfigurable Gripper: Robust Grasping and Sequential Manipulation of Thin Objects

cs.RO ·2026-08-27 ·Ziyi Zheng, Keqi Zhu, Hao Wu, Yanzhe Wang, Huixu Dong
published similarity 0.60
Abstract · Accepted by RSS2026

Robotic grippers face substantial challenges in grasping and manipulating thin objects. Most existing grippers rely on highly precise approach and grasp motions, which limits robustness and reduces applicability. This paper explores thin-object grasping using books as a representative example. Here, we propose a novel solution that integrates an active surface with underactuated compliance to achieve stable grasping of thin objects without complex control. First, an underactuated gripper with an active surface is designed. The active-surface thumb performs in-hand repositioning of the target book without requiring adjustments of the robot arm or the other fingers, while the underactuated fingers establish compliant contact conditions with the environment, and the reconfigurable structure enables reliable grasping of books under different configurations. Second, we establish a kinematic model of the gripper, and determine the initial grasp postures for two representative scenarios (books lying flat on a desktop and books vertically packed in a shelf). Third, by analyzing the physical model of a book lying on a table and its interaction with the gripper and the environment, we systematically optimize the structural parameters and grasping strategy. Finally, extensive experiments validate the effectiveness of the proposed gripper and strategy. The results demonstrate strong robustness and adaptability when grasping thin objects placed flat (including books, paper, fabric, plastic film, and mouse pad), as well as a high success rate when grasping vertically packed books. Moreover, the proposed gripper can reliably complete long sequential "grasp-place" tasks.

0.21