CS Paper Radar

DNPush: Distributed Nonparallel Pushing Force Control of Multi-Robot Systems for Object Transportation

Duy Anh Nguyen, Pham Duy Hung, Trung Dung Ngo

cs.RO eess.SY ·submitted 2026-10-03 20:59 UTC · v1

Abstract

This letter proposes DNPush, a Distributed Nonparallel Pushing force controller for cooperative object transport without inter-robot communication. Each robot uses local force measurements, a preassigned force weight, and a locally expressed desired transport direction, without requiring an object model, contact locations, a CoM estimate, or moment arm magnitudes online. DNPush regulates nonparallel force magnitudes from local force direction misalignments through a reciprocal-sine law. Under the stated contact conditions, Lyapunov analysis with LaSalle's invariance principle proves convergence to a unique rotational equilibrium, where perpendicular force contributions cancel and the net torque from normal forces is zero. Object velocity converges to the desired transport direction, and suitable contact regions exist for convex polygons. Simulations isolate the reciprocal-sine scaling mechanism, five-robot coordination, and active rotational damping. Hardware experiments with soft tactile differential-drive robots achieve a velocity direction error of 0.61 deg +/- 0.79 deg over five trials with a fixed transport direction and demonstrate object transport through waypoints with three robots.

Comment
8 pages, 8 figures. Submitted to IEEE Robotics and Automation Letters

Closest papers

Nearest neighbours by meaning across the whole index.

Distributed Cascade Force Control of Soft-Tactile-Based Multi-robot System for Object Transportation

cs.RO eess.SY ·2026-10-03 ·Duy Anh Nguyen, Nhat Minh Dinh Le, Nhan Huu Nguyen, Pham Duy Hung, Van Anh Ho +1 more
published similarity 0.71
Abstract · 6 pages, 7 figures. Published in the 2024 IEEE/SICE International Symposium on System Integration (SII)

In this paper, we present a distributed cascade force control system (DCFC) for multiple robots with the aim of pushing a rigid object towards a desired moving target without their inter-robot communication. These mobile robots are equipped with 360-degree vision-based soft tactile sensors utilized to determine contact location and resultant impact force. By investigating the dynamics of moving rigid objects on the flat, we proposed a distributed cascade control. The inner loop control incorporates contact force and positioning, ensuring the robots' pushing contact and application of the desired force to the object. The outer loop control coordinates the robots to push the object in a desired direction without inter-robot communication, regardless of the unknown object mass. The stability and convergence of the system are verified using the Lyapunov stability theory. We also conducted simulation and real-word experiments to validate the performance of the proposed control method, and the experimental results showcase the successful coordination of multiple robots in pushing an object towards a moving desired direction.

0.65

Force-Closure Condition for Cooperative Multi-robot Pushing of Rectangular Objects

cs.RO eess.SY ·2026-11-09 ·Duy Anh Nguyen, Trung Dung Ngo
published similarity 0.68
Abstract · 7 pages, 7 figures, 2 tables. Published in CAOS 2026

In cooperative object manipulation, the placement of pushing contacts determines whether force closure can be achieved and agents can generate arbitrary forces and torques on the object correspondingly. This study derives a necessary and sufficient closed-form condition for the planar force closure of a rectangular object, a common object shape in everyday settings, under four frictionless pushing contacts. For a rectangle of length $b$ and width $a$, force closure holds if and only if $(l_1+l_3-b)(l_2+l_4-a)<0$, where $l_1,l_2,l_3,l_4$ are the four edge contact locations. This condition is independent of the object's center of mass and is used to verify contact configurations before contact force allocation. When the condition is not satisfied, the signs of the two factors indicate which opposing contact pair should be adjusted. The condition and adjustment rule are then integrated into a full-pose trajectory-tracking framework as a geometric feasibility layer to demonstrate their use in control. Static wrench feasibility tests validate the proposed condition, while narrow-passage floating-body simulations show that maintaining a force-closure configuration reduces the RMS tracking errors in $x$, $y$, and unwrapped yaw from $12.05$ m, $18.11$ m, and $535.96^\circ$ to $2.24$ m, $2.66$ m, and $2.69^\circ$, respectively.

0.36

Cooperative Transport of Unknown Objects by Distributed Effort Regulation in Multi-agent Systems

cs.RO cs.MA ·2026-11-15 ·Tamzidul Mina, Shyam S. Kannan, Wonse Jo, Shaocheng Luo, Galen B. King +1 more
similarity 0.63
Abstract · 9 pages, 12 figures; supplementary video available at https://youtu.be/C2usYt0xzl8; submitted to ICRA 2027

A distributed multi-robot object transportation strategy is proposed for objects of unknown shape, size, geometry, mass and mass distribution without any prior knowledge about the object or number of robots involved in the transportation process. Robots follow the boundary of the object and dynamically determine viable pushing points. A novel object-model-free heading-error-driven pushing effort regulation method is proposed to promote goal-directed object motion; robots regulate their pushing effort using individual and collective heading errors. Robots dynamically relocate around the object boundary if a pushing point is lost or the required pushing effort exceeds its capability to correct its heading. The proposed method is validated using simple and complex shapes with convex and non-convex boundary regions and dynamically changing weight distribution of objects. Detailed analysis on the effects of robot distribution and initial object pose on the transportation performance in terms of required time and path efficiency is also presented. Scalability analysis revealed that object transportation time is dependent on the number of pushing surfaces available which in turn depends on the object size, shape, and set inter-robot safety distance. The proposed system yielded highly efficient object paths with consistent elapsed transport times over several trials robust to external disturbances such as non-uniform friction between contacting surfaces and robot wheel slip.

0.33

Ultra-Low-Impedance Robotic Gripper for High-Bandwidth and Transparent Physical Interaction

cs.RO ·2026-08-10 ·Joon Lee, Ari Choi, Seokhwan Jeong
published similarity 0.62
Abstract · ICRA 2026 (Late Breaking Result Poster)

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

0.19

Grasping and Stabilizing Tumbling Objects with Rotating-Base Multi-Arm Space Manipulators

cs.RO eess.SY ·2026-11-03 ·Farhad Aghili
top venue similarity 0.59
Abstract

This paper presents an innovative guidance and control method for a space manipulator that actively maneuvers its base to hold a tumbling object stationary relative to the base during proximity operations. This simplifies motion planning, reduces collision risk, and enables impact-free capture using single- or multi-arm configurations, with or without predefined grasping interfaces. The proposed approach involves two phases. In the pre-grasping phase, a synchronization control aligns the target's center of mass (CoM) with the system's instantaneous center of rotation (ICR), virtually rigidizing the target-servicer system to keep the object stationary for reliable grasping. In the post grasping phase, a control strategy based on Hamiltonian dynamics and optimal control stabilizes the combined system by minimizing time, fuel, or energy, while respecting base torque limits and multiple grasping constraints. For structured targets, applied forces and torques stay within their bounds; for unstructured ones, friction constraints prevent slipping. A case study demonstrates the method's effectiveness in enabling both the subsequent grasping and detumbling phases.

0.36

Safe Multi-Robot Collaborative Transport Using Density Functions

cs.RO ·2026-10-06 ·Jagannath Prasad Sahoo, Sriram S. K. S. Narayanan, Umesh Vaidya
code/datahot direction similarity 0.57
Abstract

This paper presents a hierarchical density-based model predictive control framework for safe collaborative manipulation by multiple quadrupedal robots. The framework enables a team of robots to push a shared object to a desired pose using only the initial and goal poses, without requiring a precomputed reference trajectory. A centralized box-level MPC optimizes contact forces while enforcing a control-density constraint for goal convergence and obstacle avoidance. Each robot then solves its own distributed robot-level whole-body MPC, under a stated shared-information assumption, to track its moving contact location while accounting for static obstacles and the time-varying positions of neighboring robots. The approach is evaluated in MuJoCo using whole-body contact dynamics for two and three Unitree Go2 quadrupeds collaboratively pushing rigid objects through narrow passages. Comparisons with matched Control Barrier Function and RRT* based tracking baselines demonstrate the effectiveness of the proposed density-based formulation for push-only, force- and torque-coupled manipulation tasks. Implementation videos are available at https://jaggu2606.github.io/go2-density-mpc-pushing/

0.44

Keeping Contact: Task-Adaptive Friction Margins for Bimanual Non-Prehensile Manipulation

cs.RO ·2026-10-27 ·Qian Ying Lee, Lin Yang, Domenico Campolo
top venuecode/data similarity 0.57
Abstract · Accepted for publication in IEEE Robotics and Automation Letters (RA-L)

Maintaining contact in non-prehensile manipulation requires more than nominal friction cone feasibility: a force barely inside the cone and one well inside it are both feasible, but they provide different margins against slip and contact loss. This paper uses signed friction distance to measure friction margin in force space and derives a task-adaptive margin from the force correction needed to balance pivot moment deviations in bimanual tilting. The resulting contact margins are embedded in a sequence of second-order cone programs (SOCPs), each giving a globally optimal contact force solution at a tilt angle. The optimizer balances the object about an environmental pivot while keeping robot and pivot contact forces away from the nominal friction boundary. Optimizer-level results show interpretable force redistribution and adaptation to object property changes. Real-world experiments demonstrate successful execution under object property variations and model mismatch, while fixed margin and no-margin comparisons illustrate the importance of adapting the margin to task demand. These results support signed friction distance margins as a force planning mechanism for maintaining contact in bimanual non-prehensile manipulation. Project page: https://keeping-contact.github.io/

0.60

TinyARM-X: A Series of Open-Source, Configurable, and Transparent Torque-Controlled Desktop-Scale Robotic Manipulators

cs.RO ·2026-11-18 ·Nicolas Kosanovic, Jean Chagas Vaz
similarity 0.57
Abstract · 9 pages, 5 figures. Submitted to a robotics Journal. Reviews have not come in yet

Visuomotor policies have demonstrated that imprecise low-cost robots can autonomously complete complex manipulation tasks. However, most inexpensive manipulators rely on compact and rigidly position-controlled servos for actuation, which complicate simulation, operation, and safety. This work introduces TinyARM-X, a framework for easily manufacturable, configurable, and torque-controllable low-cost (<350 USD) serial manipulators. By using a single hardware/software architecture, a <7 Degree of Freedom (DoF) TinyARM can be manually reconfigured to an operational >3 DoF robot within 10 min. Actuator modeling and dynamic compensation enable torque-controlled applications like mixed-reality impedance control teleoperation and simulator force feedback rendering. Experiments include mechanical benchmarking and real-world force-aware telemanipulation. The TinyARM-7 has a payload of 33.5 g, a max speed of 0.77 m/s, and a reach of 210 mm. Moreover, with dynamic compensation, the robot has a backdrive-breakaway force of 1.4 N and a backdrive-running force of 0.7 N. Additionally, Cartesian-Impedance Control (CIC) attains a translational stiffness of >15 N/m. Lastly, the TinyARM-X stack is open-sourced to disseminate accessible desktop-scale torque-controlled robotic manipulation to the community.

0.22