CS Paper Radar

TinyARM-X: A Series of Open-Source, Configurable, and Transparent Torque-Controlled Desktop-Scale Robotic Manipulators

Nicolas Kosanovic, Jean Chagas Vaz

cs.RO ·submitted 2026-11-18 14:55 UTC · v1

Abstract

Visuomotor policies have demonstrated that imprecise low-cost robots can autonomously complete complex manipulation tasks. However, most inexpensive manipulators rely on compact and rigidly position-controlled servos for actuation, which complicate simulation, operation, and safety. This work introduces TinyARM-X, a framework for easily manufacturable, configurable, and torque-controllable low-cost (<350 USD) serial manipulators. By using a single hardware/software architecture, a <7 Degree of Freedom (DoF) TinyARM can be manually reconfigured to an operational >3 DoF robot within 10 min. Actuator modeling and dynamic compensation enable torque-controlled applications like mixed-reality impedance control teleoperation and simulator force feedback rendering. Experiments include mechanical benchmarking and real-world force-aware telemanipulation. The TinyARM-7 has a payload of 33.5 g, a max speed of 0.77 m/s, and a reach of 210 mm. Moreover, with dynamic compensation, the robot has a backdrive-breakaway force of 1.4 N and a backdrive-running force of 0.7 N. Additionally, Cartesian-Impedance Control (CIC) attains a translational stiffness of >15 N/m. Lastly, the TinyARM-X stack is open-sourced to disseminate accessible desktop-scale torque-controlled robotic manipulation to the community.

Comment
9 pages, 5 figures. Submitted to a robotics Journal. Reviews have not come in yet

Closest papers

Nearest neighbours by meaning across the whole index.

Surgical Master Console Using General-Purpose Robot Arms and a Separable Articulated Distal Interface: Porcine In-Vivo Evaluation

cs.RO ·2026-09-27 ·Minsung Kim, Seonho Shim, Dongho Yee, Younghoon Noh, Juahn Oh +7 more
similarity 0.67
Abstract · Submitted to IEEE ICRA 2027

High-performance surgical master consoles offer intuitive articulated manipulation but are expensive and difficult to reproduce, while accessible commercial haptic devices lack built-in interfaces for surgical wrist articulation and continuous grasp. We present a laparoscopic master in which general-purpose robot manipulators provide the programmable base and surgical-specific interaction is concentrated in a separable distal adapter. Each 6-DoF arm carries a custom 2-DoF direct-drive wrist, continuous grasp sensing, and clutch-based workspace management; the complete bimanual hardware costs approximately US$5,500, below common bimanual commercial haptic references. To support sustained hand-guided use, we characterize current scaling, gravity, and break-away friction and use them for posture-dependent gravity compensation and motion-gated assistance, reducing continuous actuation and thermal loading. A common master state drives either Isaac Sim or an RCM-constrained dual-FR3 platform. Master-state publication to FR3 target update adds at most 8 ms, and tip tracking shows 0.31-0.66 mm mean delay-aligned residuals. In a porcine cholecystectomy experiment, five common operator-side metrics and hand/tip-speed distributions were compared descriptively with human in-vivo telemetry from 120 clinical Versius recordings of 99 cholecystectomy procedures; no interruption originated from the master console, and no abnormal clinical signs were recorded during the 7-day postoperative observation period. These results demonstrate a surgical master built from general-purpose robot arms with surgical-specific interaction concentrated in a separable distal interface.

0.32

Design and Characterization of a Unified Continuum Robot Actuation Platform

cs.RO ·2026-10-14 ·Yunti Xu, Aedan Mangan, Miheer Potdar, Alex Lu, Tania K. Morimoto
similarity 0.65
Abstract

Continuum robots enable dexterous access to confined spaces in applications such as minimally invasive surgery and industrial inspection. However, their actuation systems are often custom-designed for specific robot architectures and tasks, limiting reuse across publications, institutions, and applications. This paper presents a unified actuation platform that decouples actuation hardware and software from continuum robot design. The platform provides modular actuation across continuum robot classes, scales to a large number of degrees of freedom (DOFs), and integrates with conventional serial manipulators for hybrid architectures. We validate the platform on an open-sourced surgical robotic system and experimentally characterize the actuation modules, achieving sub-millimeter translational accuracy and less than $5^\circ$ rotational error over ranges of $30$~mm and $180^\circ$, respectively. We further demonstrate the platform in two surgical use cases: teleoperation of a continuum camera in a constrained environment and bimanual manipulation using $2.53$~mm concentric-tube-robot-based forceps alongside a conventional wristed instrument. All hardware designs and ROS-based software are open-sourced to facilitate reuse and further research in continuum and surgical robotics.

0.31

LocoPilot: Single-Operator Bilateral Teleoperation for Loco-Manipulation Policy Learning

cs.RO ·2026-10-20 ·Antonio Langella, Giovanni Minelli, Giovanni B. Dessy, Lorenzo Amatucci, Giulio Turrisi +2 more
code/data similarity 0.63
Abstract

Learning loco-manipulation policies requires demonstrations that capture coordinated base and arm motion on the target embodiment. Robot-free interfaces allow demonstrations to be collected independently of the target robot, increasing flexibility but without directly capturing platform-specific commands, proprioception, and body-mounted observations. On-robot teleoperation allows to capture these signals directly, but requires an interface capable of commanding the complete system concurrently. This paper presents LocoPilot, a single-operator bilateral teleoperation and data-collection framework implemented on a 12-DoF Unitree Go2 quadruped equipped with a 6-DoF AgileX Piper L manipulator, an Intel RealSense D435 wrist camera, and an Intel RealSense D405 head camera. A second 6-DoF Piper L arm, used as the leader and two handheld controllers provide simultaneous control of the base, body posture, manipulator, and gripper. The follower arm interaction forces are estimated without a dedicated force/torque sensor and rendered to the operator through a passivity-constrained haptic channel. A ROS~2 pipeline records synchronized multimodal observations together with a unified 11D action shared by teleoperation and policy deployment. Compared to prior work, LocoPilot uniquely unifies robot-in-the-loop legged data collection, force feedback without motion-capture instrumentation, and the same action interface at deployment. We evaluate the interface across multiple loco-manipulation tasks and validate the complete collection-to-deployment pipeline by fine-tuning MolmoAct2 \cite{MOLMO} on pick-and-place demonstrations and deploying on the physical robot without action retargeting or additional inverse kinematics. Code available at: https://github.com/iit-DLSLab/LocoPilot

0.21

Ultra-Low-Impedance Robotic Gripper for High-Bandwidth and Transparent Physical Interaction

cs.RO ·2026-08-10 ·Joon Lee, Ari Choi, Seokhwan Jeong
published similarity 0.63
Abstract · ICRA 2026 (Late Breaking Result Poster)

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

0.19

Reproducible Vision-Guided 6-DoF Robotic Manipulator with a Mixed Stepper-Driver Architecture and Browser-Native Control

cs.RO cs.CVeess.SY ·2026-08-24 ·Lasan Perera, Deneth Priyadarshana, Dulana Pitiwaduge, Isitha Dinujaya, Mokshan Colambage
code/data similarity 0.62
Abstract · 13 pages, 16 figures, 7 tables. Design files and firmware: https://github.com/Lasan-Perera/6-dof-arm-neuralnexus

We present the NeuralNexus Arm, an open, low-cost 6-DOF robotic manipulator built by an undergraduate engineering team, together with the design decisions and debugging experience needed to reproduce it. The arm is driven by a single STM32H743 microcontroller on a custom printed circuit board (PCB) and combines two stepper-driver strategies on one controller: push-pull 3.3 V step/direction outputs for onboard TMC2209 drivers on the three wrist joints, and open-drain outputs for external CL57T and DM542 drivers on the three high-torque proximal joints. We describe the mechanical design, mixed-driver electronics, interrupt-driven firmware, a MATLAB/Simscape-based inverse-kinematics pipeline, a browser-native control interface using the Web Serial API, and a lightweight vision pipeline for object localisation and autonomous pick-and-place tasks. We also document non-obvious hardware and firmware failure modes encountered during the transition from a development board to the custom PCB as reproducibility guidance. All design files and firmware are released openly. The platform actuates all six axes under coordinated control at a 2 kHz update rate and executes both manual and pre-recorded motions from the browser interface.

0.35

XRoboToolKit-T: Teleoperation with High Stability and Precision with Tactile Sensing for Contact-rich Manipulation

cs.RO cs.HC ·2026-09-14 ·Xiwen Dengxiong, Xueting Wang, Ke Jing, Rui Li, Yunbo Zhang
similarity 0.61
Abstract

Collecting high-quality robot data for contact-rich manipulation tasks is essential for enabling robots to acquire real-world skills. However, existing data collection solutions often lack the capability to obtain stable and high-frequency tactile feedback, limiting their effectiveness in contact-rich manipulation scenarios. In this work, we propose a versatile teleoperation system with tactile-driven assistance to enable high-frequency and stable contact-rich manipulation. The proposed XRoboToolKit-T teleoperation system incorporates a tactile-informed force control architecture, designed to ensure both stable and precise force control in contact-rich manipulation during teleoperation. The stabilizer haptic module rapidly analyzes the normal force distribution and infers pseudo shear force, enabling real-time tactile-based assistance during manipulation. The refiner haptic module integrates a vision-language-action model to predict and refine manipulation actions based on tactile sensing data and task descriptions. We apply the proposed teleoperation system to challenging contact-rich manipulation tasks, including grasping a deformable rubber pipette for liquid transfer and inserting a medical syringe into a vascular training pad, to demonstrate the effectiveness of tactile-informed force control. Furthermore, the system achieves higher data collection efficiency and improved manipulation stability compared to state-of-the-art teleoperation without tactile assistance.

0.23

RoboSpan: Learning Modular Coordination Policies for High-DoF Whole-Body Mobile Manipulation with Teleoperation

cs.RO ·2026-10-14 ·Keqiang Ren, Xuecheng Ye, Hanyu Liu, Zhihua Wang, Tao Jian +4 more
similarity 0.61
Abstract

Whole-body mobile manipulation suffers from two fundamental challenges: inherent motion heterogeneity across locomotion, arm, and hand modules, and progressive error accumulation over long-horizon multi-stage tasks. Existing teleoperation platforms also lack integrated dexterous tactile sensing to support coordinated whole-body decision-making. This paper presents RoboSpan, a high-DoF whole-body teleoperation and demonstration platform, and the Hierarchical Modular Framework (HMF) for learning modular coordination policies. HMF functionally decouples the 29-DoF action space into fine hand manipulation, arm pose adjustment, and mobile-base spatial configuration branches, and introduces the Coordinated Modular Embodied Transformer (COMET) with inter-modular cross-attention to enable dynamic information exchange and action coordination. Vision-language model driven hierarchical task decomposition structurally suppresses temporal error propagation, while a full-palm 2D tactile representation encodes distributed contact signals for cross-module tactile empowerment. Experiments on a physical 29-DoF robot demonstrate that the proposed method achieves over 20\% higher task success rate than mainstream baselines across a range of long-horizon whole-body tasks, markedly improving stability and robustness in contact-rich manipulation.

0.16

DexSuite: An All-in-One Framework for Dexterous Manipulation Across Arms, Hands, and Tasks

cs.RO ·2026-10-27 ·Anas Houssaini, Hugo He, Junming Shi, Amin Abyaneh, Ricardo Chahine +17 more
benchmarkcode/data similarity 0.61
Abstract · 7 pages, 7 figures, 2 tables. Project page: https://dexsuiteorg.github.io

Human-level dexterity remains a central open problem in robotics, yet few simulation frameworks cover the full workflow of dexterous manipulation, from setting up a robot to collecting dexterous demonstrations and evaluating policies. We present DexSuite, an all-in-one simulation framework for dexterous manipulation built on the Genesis simulator. DexSuite provides 30 tasks and assembles its 10 arms and 12 end-effectors, from parallel-jaw grippers to dexterous hands, into more than 100 single-arm robots and thousands of bimanual pairs. It also ships a standardized environment API, integrated teleoperation, and simulated tactile sensing. Moreover, we define a benchmark of 16 task-embodiment pairs spanning diverse contact complexities and horizons, and release a dataset of 4,700 successful episodes in simulation from human teleoperation, scripted experts, and learned policies. We release DexSuite as open source and hope others will build on it. Videos and datasets are available at https://dexsuiteorg.github.io

0.27