CS Paper Radar

Surgical Master Console Using General-Purpose Robot Arms and a Separable Articulated Distal Interface: Porcine In-Vivo Evaluation

Minsung Kim, Seonho Shim, Dongho Yee, Younghoon Noh, Juahn Oh, Yechan Seo, Jinseok Lee, Jiyul Lee, Seong Jeong, Hyuk Choi, Youngbin Kong, Hyoun-Joong Kong

cs.RO ·submitted 2026-09-27 07:53 UTC · v1

Abstract

High-performance surgical master consoles offer intuitive articulated manipulation but are expensive and difficult to reproduce, while accessible commercial haptic devices lack built-in interfaces for surgical wrist articulation and continuous grasp. We present a laparoscopic master in which general-purpose robot manipulators provide the programmable base and surgical-specific interaction is concentrated in a separable distal adapter. Each 6-DoF arm carries a custom 2-DoF direct-drive wrist, continuous grasp sensing, and clutch-based workspace management; the complete bimanual hardware costs approximately US$5,500, below common bimanual commercial haptic references. To support sustained hand-guided use, we characterize current scaling, gravity, and break-away friction and use them for posture-dependent gravity compensation and motion-gated assistance, reducing continuous actuation and thermal loading. A common master state drives either Isaac Sim or an RCM-constrained dual-FR3 platform. Master-state publication to FR3 target update adds at most 8 ms, and tip tracking shows 0.31-0.66 mm mean delay-aligned residuals. In a porcine cholecystectomy experiment, five common operator-side metrics and hand/tip-speed distributions were compared descriptively with human in-vivo telemetry from 120 clinical Versius recordings of 99 cholecystectomy procedures; no interruption originated from the master console, and no abnormal clinical signs were recorded during the 7-day postoperative observation period. These results demonstrate a surgical master built from general-purpose robot arms with surgical-specific interaction concentrated in a separable distal interface.

Comment
Submitted to IEEE ICRA 2027

Closest papers

Nearest neighbours by meaning across the whole index.

An Open-Source ROS 2 Framework for Shared Control in Surgical Teleoperation: Integrating the Haply Inverse3 with the da Vinci Research Kit

cs.RO eess.SY ·2026-11-19 ·Balint Varga, Sebastian Fritz, Gergely Kiss, Kristof Takacs, Peter Galambos
benchmarkcode/data similarity 0.69
Abstract

Surgical teleoperation deprives surgeons of touch, forcing visual inference of tissue forces; the commercial platforms now restoring force feedback remain closed, preventing open research on haptic shared control. This paper provides a system contribution: it presents an open-source, ROS 2-native framework that integrates the compact, three-degree-of-freedom (3-DOF) Haply Inverse3 haptic device with the da~Vinci Research Kit (dVRK). The framework includes a novel mapping strategy that combines 3-DOF translational device input with separately tracked VerseGrip orientation into 6-DOF patient-side manipulator commands. Two virtual-fixture-inspired guidance modes serve as reference implementations to evaluate the framework in a within-subjects user study on a teleoperated hot-wire benchmark task in simulation, and the architecture is further demonstrated on physical dVRK hardware. Relative to unassisted manual control, linear guidance significantly reduced both the number of wire contacts and the task completion time, whereas the progressive-stiffness guidance produced consistent but statistically non-significant trends in the same direction. Subjective ratings of workload, agency, and satisfaction showed favorable descriptive trends for the guidance modes. The results demonstrate the feasibility of haptic shared control with a compact device coupled to the dVRK and provide an openly available, reproducible platform for future research. They further suggest that simpler linear feedback may be more robust for inexperienced operators than more complex profiles.

0.25

Design and Characterization of a Unified Continuum Robot Actuation Platform

cs.RO ·2026-10-14 ·Yunti Xu, Aedan Mangan, Miheer Potdar, Alex Lu, Tania K. Morimoto
similarity 0.68
Abstract

Continuum robots enable dexterous access to confined spaces in applications such as minimally invasive surgery and industrial inspection. However, their actuation systems are often custom-designed for specific robot architectures and tasks, limiting reuse across publications, institutions, and applications. This paper presents a unified actuation platform that decouples actuation hardware and software from continuum robot design. The platform provides modular actuation across continuum robot classes, scales to a large number of degrees of freedom (DOFs), and integrates with conventional serial manipulators for hybrid architectures. We validate the platform on an open-sourced surgical robotic system and experimentally characterize the actuation modules, achieving sub-millimeter translational accuracy and less than $5^\circ$ rotational error over ranges of $30$~mm and $180^\circ$, respectively. We further demonstrate the platform in two surgical use cases: teleoperation of a continuum camera in a constrained environment and bimanual manipulation using $2.53$~mm concentric-tube-robot-based forceps alongside a conventional wristed instrument. All hardware designs and ROS-based software are open-sourced to facilitate reuse and further research in continuum and surgical robotics.

0.31

TinyARM-X: A Series of Open-Source, Configurable, and Transparent Torque-Controlled Desktop-Scale Robotic Manipulators

cs.RO ·2026-11-18 ·Nicolas Kosanovic, Jean Chagas Vaz
similarity 0.67
Abstract · 9 pages, 5 figures. Submitted to a robotics Journal. Reviews have not come in yet

Visuomotor policies have demonstrated that imprecise low-cost robots can autonomously complete complex manipulation tasks. However, most inexpensive manipulators rely on compact and rigidly position-controlled servos for actuation, which complicate simulation, operation, and safety. This work introduces TinyARM-X, a framework for easily manufacturable, configurable, and torque-controllable low-cost (<350 USD) serial manipulators. By using a single hardware/software architecture, a <7 Degree of Freedom (DoF) TinyARM can be manually reconfigured to an operational >3 DoF robot within 10 min. Actuator modeling and dynamic compensation enable torque-controlled applications like mixed-reality impedance control teleoperation and simulator force feedback rendering. Experiments include mechanical benchmarking and real-world force-aware telemanipulation. The TinyARM-7 has a payload of 33.5 g, a max speed of 0.77 m/s, and a reach of 210 mm. Moreover, with dynamic compensation, the robot has a backdrive-breakaway force of 1.4 N and a backdrive-running force of 0.7 N. Additionally, Cartesian-Impedance Control (CIC) attains a translational stiffness of >15 N/m. Lastly, the TinyARM-X stack is open-sourced to disseminate accessible desktop-scale torque-controlled robotic manipulation to the community.

0.22

Embodiment-Aware Planning for Heterogeneous Bimanual Manipulation

cs.RO ·2026-10-16 ·Sukhvansh Jain, Anurag Maurya, Shivam Vats, Narendra Kumar Dhar, Ravi Prakash
similarity 0.66
Abstract · Please find the project website here: https://sukhvansh2004.github.io/Bimanual-Manipulation/

Many manipulation tasks that are effortless for dexterous human hands remain challenging for robotic systems equipped with simple, task-specialized grippers. Industrial platforms commonly rely on end-effectors such as suction cups or parallel-jaw grippers, yet no single mode can reliably satisfy the diverse constraints encountered across different phases of complex manipulation tasks, including pickup, reorientation, insertion, and constrained placement. In this work, we investigate whether complementary simple grippers within a heterogeneous bimanual setup can collectively realize tasks that exceed the capability of any individual gripper alone. Given a single human demonstration specifying the desired object motion, we formulate embodiment-aware execution as a finite-horizon optimization over arm-trajectory assignments. At each segment, the planner determines whether single-arm manipulation or a coordinated dual arm handover is required, jointly reasoning over heterogeneous grasp feasibility, motion constraints, manipulability, and cross-gripper compatibility. Exploiting this formulation, we compute globally consistent assignments with explicit switching regularization. Experiments on a dual Franka FR3 platform equipped with suction and parallel-jaw grippers demonstrate improved feasibility and reliability in tasks that are infeasible under single-gripper execution.

0.29

RUMI: A Robotiq-Matched Universal Manipulation Interface for Robot Learning with Augmented Reality and Haptic Feedback

cs.RO cs.AI ·2026-11-11 ·Kevin Avdiu, Seongjin Bien, Yannik Blei, Philine Meister, Johannes Hechtl +4 more
similarity 0.66
Abstract

Many manipulation tasks require carefully controlled contact forces for successful execution, yet large-scale, force-aware datasets remain scarce. Handheld interfaces can help by transmitting interaction forces directly through the operator's arm, but most existing designs are tailored to simple linear grippers and do not match the nonlinear mechanics of widely used robotic grippers. We present RUMI, a handheld universal manipulation interface matched to the Robotiq 2F-85 with exchangeable fingertip sensors that preserves the target gripper geometry while enabling natural input before contact and force measurement after contact. By integrating the tracking system into a virtual reality headset, our method provides real-time augmented reality feedback about the kinematic feasibility of motion on the target robot platform. We further introduce a haptic feedback mechanism that supports force-aware teleoperation for simulated and real robots. A user study shows fewer episodes containing joint-limit violations with live robot visualization and pose initialization (3/50) than without augmented reality (16/50). We additionally train imitation policies from demonstrations, collected using two different fingertip modalities enabled by the gripper-matched hardware, and assess the haptic interface's capability for collecting force-aware teleoperation datasets in simulation.

0.04

TacBPM: A Tactile-conditioned Behavior Prior Model for Dexterous Reorientation

cs.RO ·2026-09-16 ·Jie Yin, Wanli Xing, Zeyuan Zhao, Xuezhou Zhu, Zhijie Deng +1 more
similarity 0.65
Abstract · Corresponding to: Jie Yin (jie.yin@sharpa.com)

Dexterous in-hand manipulation requires policies that coordinate high-DoF hand joints through intermittent, contact-rich interaction. Beyond target-orientation tracking, such policies must discover finger gaits that preserve object stability while adapting to geometry, anisotropy, pose, contact, and sensing changes. We propose \method, a tactile-conditioned behavior prior model for dexterous reorientation. \method distills multi-scale sphere specialists into a latent controller and lets downstream policies reuse the fixed tactile prior through residual latent actions, reducing renewed exploration from raw joint commands. The prior conditions on tactile-proprioceptive history so latent behavior reflects the current hand-object interaction. We evaluate arbitrary-pose transfer across anisotropic objects, commanded-axis rotation, and an arm-hand Grasp-to-AnyPose task in which the robot must grasp, lift, transport, and reach goal poses for novel tool geometries and generalized placements. Extensive experiments demonstrate that the proposed method accelerates training and enables stable policies where matched raw-action PPO remains near failure, with successful sim-to-real transfer in in-hand and arm-hand tasks.

0.20

Koala Gripper: Co-designing Robotic Grippers and Data-Capture Devices for Scaling Dexterous Manipulation Learning

cs.RO ·2026-08-20 ·Amar Hajj-Ahmad, Zubin Kremer Guha, Tim Fofonoff, Zhi Ern Teoh, Ciarán T. O'Neill +6 more
similarity 0.65
Abstract · Paper website: http://koalagripper.rai-inst.com Paper video: http://www.youtube.com/watch?v=ZoygFCWAVhg

As the demand for larger manipulation datasets grows, handheld robotic gripper data collection and the associated gripper designs become more vital. Current data collection device designs trend towards matching the morphologies of existing robotic grippers, sacrificing ergonomics and manipulation performance. In this paper, we propose a co-design framework that guides the simultaneous development of both data collection and robotic execution devices by weaving both platform constraints into the design process. Through this workflow, we present the Koala Gripper system, a data capture device and robotic gripper platform that improves dexterity and grasp capability compared to parallel jaw grippers while preserving scalability and ease-of-use. The design introduces a novel force-optimized finger/trigger linkage mechanism with directional reflected mass characteristics, a unique monolithic dual-thumb, and user-centered ergonomic design. The design's actuated robotic fingers are backdrivable, with effective mass on the order of tens of grams. We show that these grippers are capable of secure grasps over a wide range of objects, forceful tool use, and precise singulation. We further validate the platform by deploying it with an end-to-end data collection and policy execution pipeline that highlights its capabilities through learning from demonstration. More information available at http://koalagripper.rai-inst.com

0.47

A Direct Rigid Transmission 2-DoF Wrist Extension for Tendon-Driven Hand

cs.RO ·2026-09-19 ·Yujie Pang, Sadman Sakib, Mohammad Abdullah Al Faruque
published similarity 0.65
Abstract · Accepted at "IROS 2026 Sensors and Actuators for Dexterous Manipulation Workshop"

Dexterous manipulation in confined spaces requires local control of hand orientation. Without a wrist, a dexterous hand must obtain this local orientation through coordinated motion of the robot arm, often involving several joints and a more complex end-effector path. We present CRAFT-Wrist, a concentric 2-DoF wrist extension that mounts between a robot arm and the CRAFT Hand without modifying the hand. Two XC430-T240BB-T servos drive sideways and front-back rotation through short rigid transmissions. Our initial hardware prototype actuates both axes under load, achieving a demonstrated workspace of $\pm20^{\circ}$ in radial--ulnar deviation (left--right) and a front-back range of $+80^{\circ}$ in flexion and $-18^{\circ}$ in extension. We characterize the resulting finger-motor loading across several wrist postures and demonstrate how the wrist supplies local orientation in grasping, nail hammering, and blackboard wiping. Demonstrations and assembly instructions are available at https://craft-wrist.github.io/.

0.60