CS Paper Radar

A Quasi-Direct-Drive Underactuated Asymmetric Hand for Dexterous and Efficient Grasping and Manipulation

Benjamin Davis, Chase Kidder, Hannah S. Stuart

cs.RO ·submitted 2026-09-23 02:17 UTC · v1

Abstract

In this paper, we present the Berkeley QUAD (Quasi-direct-drive, Underactuated, Asymmetric Design) Hand, a four-finger anthropomorphic robotic hand with 11 degrees of freedom and 8 degrees of actuation. The design utilizes QDD actuation at the base of each finger, enabling high force transparency for dexterous, adaptive performance. However, the low torque density of these actuators traditionally presents major issues with size, weight, and thermal limits. We overcome this by applying bio-inspired asymmetry, delegating dexterity to the radial fingers through individual QDD actuation, and strength to the ulnar finger through an underactuated, compliantly coupled transmission driven by a larger QDD motor. A novel preloaded, linkage-based transmission permits this ulnar coupling in a way that preserves human-like workspace reachability. Under light loads, the ulnar motor drives the third (middle) finger directly for dexterity while the fourth (ring) finger mirrors its motion. However, under larger loads, the middle finger complies while the motor drives the ring finger further downwards and inwards toward the center of the grasp to apply better closure forces. Hardware evaluations validate this architecture, demonstrating that the hand achieves 29 out of 33 Feix taxonomy grasps and exhibits backdrive forces as low as 50 g for delicate interactions. Additionally, the underactuated fourth finger improves grasp closure and provides the spatial efficiency necessary for larger actuation, yielding up to a 96-fold reduction in heat generation during sustained loading. Webpage: https://benudavis.github.io/berkeley-quadhand/

Closest papers

Nearest neighbours by meaning across the whole index.

Ultra-Low-Impedance Robotic Gripper for High-Bandwidth and Transparent Physical Interaction

cs.RO ·2026-08-10 ·Joon Lee, Ari Choi, Seokhwan Jeong
published similarity 0.73
Abstract · ICRA 2026 (Late Breaking Result Poster)

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

0.19

A fully articulated humanoid dexterous hand with human-level joint structure enabled by linkage-based actuation

cs.RO ·2026-10-27 ·Jihao Li, Jianguo Wang, Haotian Guo, Yanzhe Wang, Guodong Lu +1 more
similarity 0.68
Abstract

Humanoid dexterous hands are a core component of embodied intelligence, enabling robots to translate high-level intent into rich and adaptive physical interaction. However, existing designs remain constrained by a persistent trade-off among anthropomorphic kinematic complexity, mechanical robustness, load capacity and control simplicity, limiting dexterous manipulation in unstructured environments. Here we present Torch-Hand, a fully articulated humanoid dexterous hand that replicates the joint structure and motion hierarchy of the human hand with 21 degrees of freedom (DOF), comprising a highly articulated five-DOF thumb and four DOF in each of the remaining fingers. The differentiated thumb integrates multi-axis CMC motion to provide broad opposition and flexible contact orientation relative to the four fingers. Unlike tendon-driven or hybrid actuation approaches, Torch-Hand adopts an entirely linkage-based transmission architecture. By integrating screw-linkage actuation, the hand achieves high grasping force and substantial payload capacity while maintaining a compact anthropomorphic form. Its actuation architecture is optimized for control tractability, with all actuators integrated within the palm and arranged in a serial-robot-like configuration that establishes a direct correspondence between motor motion and joint kinematics. This architecture mechanically decouples functional DOF to reduce unintended inter-joint motion propagation, while allowing independently addressable DOF to be actively coordinated into coupled multi-joint motion patterns during complex manipulation. Comprehensive experiments assess reachable workspace, coordinated fingertip trajectories, thumb opposition, 33-grasp taxonomy coverage, grasping force, payload capacity and task-level manipulation. These results establish Torch-Hand as a robust hardware foundation for dexterous embodied manipulation.

0.22

ORBIT: A Modular Multi-finger Robotic Hand Platform with Rotational Finger Reconfiguration

cs.RO ·2026-10-23 ·Benito Ribadeneira, Siqi Shang, Lillian Chin
similarity 0.65
Abstract · NA

Despite the popularity of multi-fingered robotic hands for dexterous manipulation, there is no systematic platform to compare different hand morphologies against one another. We present ORBIT (Orbital Reconfigurable Base-actuated Integrated Theta-motion Hand), a modular platform designed to enable principled exploration of multi-fingered hand morphology. The core contribution of ORBIT is a rotating knuckle mechanism, where independent fingers travel around a cylindrical palm via a belt drive. This enables ORBIT to perform quick recon- figuration (< 1 s) of finger layout without hand disassembly. ORBITs a robust system, with finger average angular velocity of 1.57 rad / s1 and a root finger force resistance of 50 N. Using a three fingers instantiation of ORBIT, we demonstrate an initial pilot grasping study, comparing anthropomorphic, isometric, and Barrett-style finger layouts across eleven objects of varied size, shape, and texture. We further demonstrate how ORBITs nonanthropomorphic orbital DOF enables the achievement of tasks that would be difficult to perform with fixed-knuckle designs, such as cube face reorientation, lid threading, and precision pinching of sub-centimeter objects. These results establish ORBIT as a viable platform for direct apples to apples comparison of multi-fingered hand morphologies for specific manipulation tasks

0.21

PACT: Pose-Robust Actuation Co-Design for Tendon-Driven Robotic Hands

cs.RO ·2026-11-03 ·Prashant Kumar, Rachael Granberry, Taylor Niehues, Andrew A. Stanley, Gabe Pirie
similarity 0.65
Abstract

Humanoid robotic hands must provide sufficient force, speed, and backdrivability within a human-scale envelope. Tendon-driven transmissions address this challenge by relocating actuators to the palm and forearm, but routing paths, moment arms, and capstan dimensions jointly determine both force capability and joint speed, so selecting them sequentially satisfies one requirement at the expense of the other. This paper presents a pose-robust actuation co-design for tendon-driven robot hands (PACT) framework that optimizes tendon routing, moment arms, and capstan dimensions under pose-dependent force requirements and drivetrain-bandwidth constraints. A feasible-force formulation enforces actuator bounds and equilibrium at all joints, while a max-min objective maximizes task-force coverage at the weakest pose. Applied to a four-degree-of-freedom finger, the framework produces an asymmetric N + 1 tendon topology using quasi-direct-drive actuators. Across eight poses, the design achieves task-force coverage of 0.88-1.00 and a predicted 5 Hz minimum isolated-joint flexion/extension bandwidth within a 70th-percentile human-size envelope. Prototype measurements deviate from predictions by up to 24.5%, primarily due to unmodeled transmission losses. These results indicate that co-designing routing with the drivetrain can meet pose-dependent force requirements without relaxing the bandwidth constraint, paving the way for human-sized robotic hands with human-level performance.

0.08

PHD-Hand: A Printable Humanoid Dexterous Hand with Linkage-Driven 3-DOA Digits

cs.RO cs.AI ·2026-10-21 ·Neel Adwani, Muhaiminul Islam Akash, Saffia Ouali, Ethan Liu, Cong Wang
published similarity 0.65
Abstract · Submitted and Accepted at IEEE-RAS International Conference on Humanoid Robots (Humanoids 2026). 8 pages. Supplementary video: https://lnkd.…

Currently, dexterous humanoid robot hands are widely considered the final hardware bottleneck that hampers generalist robots from physically assisting people at home and work. As conventional tendon-driven designs suffer from high cost, demanding maintenance, poor reliability, and short durability, alternative linkage-driven designs have increasingly gained attention. Despite their potential to avoid the weaknesses of tendon-driven hands, integrating multiple degrees of actuation (DOA) in a single digit with linkage drivetrains is a challenge for design and fabrication. Only a few studies have managed to present functional humanoid hands that are completely linkage-driven and have at least three DOAs per digit without compromising actuator placement and other design preferences. Our work introduces a new linkage-driven hand featuring a unique flexure hinge. Together with elastic drive rods made of spring steel, the linkage drivetrains are significantly simplified. Unlike other linkage-driven designs of similar dexterity, our design does not require many miniature moving parts. As a result, the hand can be fabricated easily with a budget 3D printer. This not only significantly lowers the barrier to entry for using and developing dexterous humanoid robot hand functions, but also allows the hands to be sized much closer to regular human hands. The design offers desirable kinematic advantages as well. A prototype is evaluated for grasping and object manipulation. In addition, this paper presents our latest findings on kinematics and control of the hand.

0.25

Design and Validation of an Antagonistic Tendon-Driven Dexterous Robotic Hand with Bidirectional Operation

cs.RO ·2026-09-28 ·Chunghyeon Lee, Hyukjun Kwon, Sungeon Kim, Saehyun Moon, Seokhwan Jeong
similarity 0.62
Abstract

Dexterous robotic hands typically reproduce human hand morphology but inherit its one-sided grasping workspace, requiring wrist or arm reorientation to grasp from the opposite side. Existing reversible hands generally rely on non-anthropomorphic, soft, or task-specific finger arrangements, whereas conventional five-digit anthropomorphic hands remain designed primarily for palmar-side grasping. This paper presents an anthropomorphic, human-scale (200 mm length), lightweight (220 g), 3D-printed, 17-DoF robotic hand built on a bidirectional antagonistic tendon-routing mechanism, in which flexion/extension (except the coupled joint) and abduction/adduction at joints are actively driven without passive return springs. The proposed routing mechanism allows all degrees of freedom to cross their neutral configuration and form grasp closures on either the palmar or dorsal side. Experimental evaluation demonstrates an average motor-to-joint transmission error of 3.0%, an average joint transmission bandwidth of 13.2 Hz, a maximum fingertip force of 29 N, and a positioning repeatability up to 0.15 mm. The hand further achieves a Kapandji score of 8, successfully performs all 33 GRASP Taxonomy grasp types, and performs palmar- and dorsal-side grasping tasks, validating bidirectional operation in a compact, human-scale platform.

0.35

A Direct Rigid Transmission 2-DoF Wrist Extension for Tendon-Driven Hand

cs.RO ·2026-09-19 ·Yujie Pang, Sadman Sakib, Mohammad Abdullah Al Faruque
published similarity 0.62
Abstract · Accepted at "IROS 2026 Sensors and Actuators for Dexterous Manipulation Workshop"

Dexterous manipulation in confined spaces requires local control of hand orientation. Without a wrist, a dexterous hand must obtain this local orientation through coordinated motion of the robot arm, often involving several joints and a more complex end-effector path. We present CRAFT-Wrist, a concentric 2-DoF wrist extension that mounts between a robot arm and the CRAFT Hand without modifying the hand. Two XC430-T240BB-T servos drive sideways and front-back rotation through short rigid transmissions. Our initial hardware prototype actuates both axes under load, achieving a demonstrated workspace of $\pm20^{\circ}$ in radial--ulnar deviation (left--right) and a front-back range of $+80^{\circ}$ in flexion and $-18^{\circ}$ in extension. We characterize the resulting finger-motor loading across several wrist postures and demonstrate how the wrist supplies local orientation in grasping, nail hammering, and blackboard wiping. Demonstrations and assembly instructions are available at https://craft-wrist.github.io/.

0.60

ARTiS: An Adaptive Robotic Gripper for Enhanced Tool Manipulation in Disassembly Applications

cs.RO ·2026-09-03 ·Roman Mykhailyshyn, Yukiyasu Domae, Kensuke Harada
top venue similarity 0.61
Abstract

Grasping and holding tools while using them presents a considerable challenge not only for robots but also for humans. Such a challenge is particularly noticeable in processes involving assembly and disassembly, where efficiency and consistency depend on performing rapidly adaptive tasks. Nonetheless, contemporary robotic grasping technologies that can securely manipulate tools during operation frequently have significant constraints. In this paper, introduce ARTiS (Adaptive Robotic Tool Gripper in Disassembly Systems), a novel gripper that combines the adaptability of soft grippers, the dexterity of anthropomorphic hands, and the robustness of rigid mechanisms with a soft palm and fingertips. This unique combination makes it possible to hold tools securely in a variety of situations through using active jamming in the palm and fin-ray adaptation in fingertips. Furthermore, high finger dexterity is achieved through the seven degrees of freedom design, which enables the fingertips to orient to any surface, both for automated solutions and collaborative tasks. A comprehensive evaluation was conducted using a range of conventional disassembly tools to assess the gripper's compliance, durability, and functional versatility. More information, hardware instructions, and videos at https://romanmykhailyshyn.github.io/artis/

0.30