CS Paper Radar

Real-Time Reference Shaping for Servo Systems

Zehui Lu, Yebin Wang, Go Sato, Fujita Tomoya

eess.SY ·submitted 2026-08-31 14:05 UTC · v1

Abstract

This paper addresses real-time motion planning for servo systems subject to nonlinear, state-dependent actuator constraints. A reference reshaping method is proposed that combines analytical optimality with high computational efficiency. Using Karush-Kuhn-Tucker conditions, the problem structure is explicitly characterized, and it is shown that the optimal solution lies within a finite set of candidate points. The complete solution set is constructed via closed-form expressions and a small-scale eigenvalue problem, yielding a deterministic algorithm that recovers the exact optimal solution without iterative optimization or root-finding. To address kinematic mismatch induced by aggressive commands, a real-time trajectory compensator is introduced to correct accumulated position error while preserving feasibility. Simulation results demonstrate significant computational speed improvements over existing methods, enabling real-time implementation at frequencies approaching 100 kHz.

Closest papers

Nearest neighbours by meaning across the whole index.

Robotic Servo Tracking of Moving Targets with Dynamic Imitation Constraints

cs.RO ·2026-09-13 ·Yazhe Luo, Sipu Ruan, Yifei Li, Diansheng Chen
hot direction similarity 0.61
Abstract

Imposing explicit trajectory constraints in robot visual servoing remains challenging. Existing tracking methods achieve fast responses by mapping visual residuals to control velocities, but they have weak constraints on the intermediate motion process, which lead to trajectory discontinuity, oscillation, or conservative behaviors. To enable constrained tracking for moving targets, this paper proposes a servo tracking method based on imitation trajectory constraints. A dynamic model describing the robot approaching a moving target is formulated and analyzed for convergence. A time-scalable deformation mechanism and a trajectory modulation incorporating shape and amplitude components are introduced to generate a series of trajectories in real time, from which tracking points are adaptively determined to form dynamic constraints. The robot velocity is then computed from target pose differentials or tracked key features to follow the constrained trajectory. Simulation and real-world experiments demonstrate that the proposed method can achieve dynamic obstacle avoidance and high-precision convergence compared with several state-of-the-art methods in complex environments.

0.33

Optimal Operating-Point Selection for Single-Linearization Trajectory Planning of Nonlinear Robot Manipulators

cs.RO eess.SY ·2026-11-13 ·Bhanuka Dayawansa, Rohan Munasinghe
published similarity 0.59
Abstract · 6 pages, 5 figures. Accepted for presentation at the 2026 IEEE International Conference on Advances in Computing (IEEE ICAC 2026)

Single-point linearization provides a computationally efficient basis for optimization-based trajectory planning of nonlinear robot manipulators. However, planning performance depends on the selected linearization point. This paper presents an offline performance-driven approach that treats the location of a single linearization as an optimization variable. Candidate operating points are sampled from a common cubic seed trajectory, and each corresponding affine model is used to solve an identical constrained finite-horizon quadratic program (QP). The resulting control sequences are executed on the original nonlinear dynamics, and the operating point minimizing the nonlinear trajectory objective is selected through grid search and bounded refinement. Evaluation on four point-to-point motions of a three-degree-of-freedom UR5 manipulator yields optimal normalized operating-point locations between 0.325 and 0.935, demonstrating trajectory-dependent selection. Compared with the best-performing conventional initial, midpoint, or terminal linearization, the proposed approach reduces the nonlinear trajectory objective by 17-18%, 21-22%, 37-38%, and 7-8% across the four tasks, respectively. Additional nonlinear execution with identical PID feedback correction confirms that the performance advantage persists for a representative task. These results demonstrate that systematic operating-point selection can substantially improve single-linearization trajectory planning while preserving a fixed affine planning model.

0.33

MR-MPCC: Model Predictive Contouring Control for Robotic Manipulator Tracking under Moving Reference Frames

cs.RO ·2026-10-15 ·Chonghao Cheng, Tiancheng Li, Jonathan Woolfrey, Liang Zhao, Shoudong Huang
published similarity 0.57
Abstract · Accepted by The IEEE/RSJ International Conference on Intelligent Robots and Systems 2026 (IROS 2026)

Maintaining small path-tracking errors under moving reference frames is essential for robotic manipulation tasks with tight execution tolerances, such as machining and surgical automation. Conventional time-indexed controllers, including tracking Model Predictive Control (MPC), rely on a fixed temporal correspondence with the reference trajectory and may therefore accumulate path-relative error under abrupt reference-frame motion or timing mismatch. This paper presents MR-MPCC, a Model Predictive Contouring Control (MPCC) framework for velocity-controlled robotic manipulators with 6-DoF end-effector pose regulation under Moving-Reference disturbances. A hierarchical control architecture is adopted, in which an upper-level MPCC optimizes path progress while penalizing contouring and orientation errors, and a constrained resolved motion rate control (RMRC) layer maps the commanded Cartesian twist to feasible joint velocities under joint-level and safety constraints. MR-MPCC is implemented in a ROS2--MuJoCo pipeline and validated on a UR5e platform under moving-reference disturbances, where the path frame is perturbed and tracked by electromagnetic sensors. Compared with PI control and time-indexed tracking MPC under matched disturbance, MR-MPCC achieves lower geometric path-following error and smaller deviations in the moving path frame, demonstrating improved path-following performance under reference-frame motion.

0.44

Residual Reinforcement Learning for Visual Servo Control with Zero-Shot Sim-to-Real Transfer

cs.RO eess.SY ·2026-11-14 ·Mahdi Nobar, Alisa Rupenyan, John Lygeros, Jürg Keller
similarity 0.56
Abstract · This manuscript is currently under review in IEEE Robotics and Automation Letters (RA-L)

We address tracking a moving object on a conveyor with a Franka Emika Panda robot arm, despite an imprecise digital twin, measurement errors, and noise. Our novel approach augments a loop-shaped inverse-Jacobian PI controller with a residual policy learned via Soft Actor-Critic in the digital twin. A delay-compensated Kalman filter fuses out-of-sequence camera measurements to provide latency-aware moving target position estimates. We compare the achieved performance to a performance bound for a class of model-based controllers derived from a frequency-domain sensitivity analysis, quantifying the minimum achievable error imposed by uncertain kinematic model mismatch. Simulation and hardware experiments indicate that our residual policy drives tracking error below the bound. Across conveyor speeds (27.9-41.8 mm/s), our method reduces mean tracking errors from 1.1-1.4 mm (baseline inverse-Jacobian PI) to 0.3-0.7 mm. These results show that learning residual corrections in a limited-fidelity simulator, combined with delay compensation, can substantially improve model-based control under modeling and measurement uncertainties while maintaining reliable sim-to-real transfer.

0.23

Control of Linear Dynamical Systems with Operational Constraints

eess.SY ·2026-11-06 ·Marcel Menner, Eugene Lavretsky
theory similarity 0.56
Abstract

This paper presents a method for designing servo-controllers that enforce operational constraints on multi-input multi-output linear time-invariant dynamical systems. The proposed method introduces a control augmentation that complements a baseline controller to ensure forward invariance of state/output trajectories within prescribed box constraints. The derivations of the control design are based on the Nagumo Theorem, the Comparison Lemma, and principles from min-norm optimal control akin to the theory of Control Barrier Functions. Importantly, an explicit piecewise-linear feedback control law is derived, which provides continuous enforcement of constraints without online optimization, enabling rigorous stability and robustness analysis via classical linear systems theory. Extensions to handle estimation errors in output feedback and integral action in proportional-integral control are provided. Theoretical results are validated through flight control simulation studies that demonstrate input/output constraint satisfaction, robustness to disturbances, and closed-loop stability. The proposed method offers a mathematically rigorous, practical, and analyzable alternative to common heuristic or optimization-intensive constrained control strategies.

0.22

Planning along Differentiable Charts of Constraint Manifolds with General-Purpose IK Solvers

cs.RO ·2026-09-09 ·Thomas Cohn, Seiji Shaw, Harel Biggie, Travis Manderson, Nicholas Roy +1 more
theory similarity 0.56
Abstract · 8 pages, 4 figures, 3 tables. Under review. Project website: https://cohnt.github.io/inverse-function-theorem-parameterization/

Planning trajectories for robot manipulators under kinematic equality constraints restricts feasible motions to a measure-zero submanifold of the configuration space, requiring special algorithmic treatment. A promising strategy is parametrizing the set of feasible configurations using analytic inverse kinematics (IK). Bespoke analytic IK functions can be written to be differentiable, a necessary property for gradient-based trajectory optimization. But the vast majority of IK functions are computed by automated meta-solvers like IKFast, and are difficult to modify for differentiability. We present a new approach for computing gradients of analytic IK parameterizations: we leverage the inverse function theorem to recover the desired gradients from the ordinary forward kinematic Jacobian. Furthermore, we present a least-squares domain extension and an optimization-amenable description of the reachability constraint, which preserves gradient signal outside the reachable workspace. We demonstrate the efficacy of our approach through numerical experiments and downstream tasks, including a hardware demonstration of an RB-Y1 picking up a box and placing it on a table. Project website: https://cohnt.github.io/inverse-function-theorem-parameterization/

0.54

Profile-Anchored Control: Velocity Shaping with Exact Disturbance Rejection and Transient-Free Replanning

eess.SY math.OC ·2026-11-19 ·Christian Fredrik Sætre, Morten Dinhoff Pedersen
theory similarity 0.55
Abstract

In many motion-control problems, how a target is approached matters as much as whether it is reached: speed and deceleration must stay within actuator, safety or comfort limits despite unknown loads and disturbances. Position-dependent velocity profiles provide a natural way to describe such requirements. We show that the square of such a profile can be used both to plan the motion and to construct the controller that executes it. Our main result, profile-anchored control with exact rejection (PACER), recovers the nominal motion after a finite time under an unknown gain and load, and then allows the profile to be replaced mid-motion without a transient. It combines a static law for scalar second-order systems with a dynamic law for first-order ones, used for disturbance rejection. The static law guarantees uniform global asymptotic stability under an unknown input gain with a known lower bound, and finite-time stability under local homogeneity, while the first-order law gives analogous guarantees under disturbances of bounded rate and provides the exact rejection in PACER. Replanning of a profile under speed, acceleration and jerk limits can be formulated as a convex program. The approach is illustrated on a simulated elevator.

0.25

Reachability-Guided Sequential Quadratic Programming-Guarded Model Predictive Path Integral for Safe Nonlinear Predictive Control

cs.RO eess.SY ·2026-10-03 ·Alexandre Didier, Jason J. Choi, Namhoon Cho, Claire J. Tomlin, Melanie N. Zeilinger
similarity 0.54
Abstract

Safe robot control often requires combining long-horizon performance optimization with hard state and input constraints, but existing approaches tend to address this tradeoff partially. Sampling-based model predictive control (MPC) methods such as model predictive path integral (MPPI) are effective in handling nonlinear and nonconvex environments, yet their finite-sample rollouts and unconstrained weighted-average update can return an unsafe control. Deterministic nonlinear MPC can explicitly incorporate constraints, but its real-time safety and performance depends strongly on warm starts and local convergence. Hamilton--Jacobi reachability (HJR) provides rigorous safety certificates, but offline value-function computation remains practical only for reduced-order models. We propose ReSQ-MPPI, a reachability-informed generation--refinement architecture that combines these complementary strengths. An HJR value function computed offline for a reduced-order model guides online MPPI sampling toward safe, promising trajectory candidates. The MPPI solution is then refined by a small number of sequential quadratic programming (SQP) iterations in a full-order MPC problem. A key observation is that the standard MPPI inference step is an unconstrained weighted least-squares problem; ReSQ-MPPI replaces it with a constrained MPC refinement that recovers the MPPI update when it is feasible and minimally modifies it otherwise. Simulations in cluttered navigation and autonomous racing environments demonstrate that ReSQ-MPPI improves safety and performance over standalone MPPI, MPC, and reachability-filtered sampling-based control baselines.

0.18