CS Paper Radar

Before the Tipping Point: Force-Guided Active Perception for Shape-Agnostic Estimation of 3D Centers of Mass

Steven M. Hyland, Jing Xiao, Cagdas D. Onal

cs.RO ·submitted 2026-09-11 14:22 UTC · v1
published

Abstract

Estimating the 3D center of mass of unknown objects is challenging when grasping is infeasible, geometry is irregular, or mass distribution is uneven. We present a force-based method that estimates CoM height and mass from a single sub-critical tipping experiment by a robot manipulator. The robot applies a quasistatic elevated push and retract motion, using force-angle measurements recorded during tipping to identify parameters from the object trajectory. Our proposed push-retract cycle mitigates frictional bias, enabling generalized fitting. We experimentally validate our method using a robot manipulator with a six-axis force torque sensor on varying types of objects without prior shape information and without specific models. We also propose a method to prevent toppling, keeping the object in a sub-critical tipping regime by leveraging a safety margin. In experimental studies, our method recovers mass, CoM height, and toppling angle with relative errors below 5.0 percent across all unknown objects. This work demonstrates reliable 3D inertial parameter estimation under proper safety thresholds in tipping. Our proposed method informs and enables reliable non-prehensile manipulation and robotic grasping of challenging objects that were previously infeasible.

Comment
For associated video, visit https://stevenmhyland.com/assets/videos/IROS2026.mp4

Closest papers

Nearest neighbours by meaning across the whole index.

Multi-Modal Non-Prehensile Estimation of Physical Parameters via Press-and-Pull Tipping

cs.RO ·2026-09-27 ·Steven M. Hyland, Jing Xiao, Cagdas D. Onal
similarity 0.76
Abstract

Recovering physical properties of unknown objects through non-prehensile interaction is challenging because no single manipulation primitive reveals all relevant parameters. Planar pushing couples mass and friction, while conventional tipping cannot recover friction and may fail entirely when low-friction or curved-base objects slide or rotate instead of tipping. We introduce a multi-modal estimation framework that combines a sliding interaction with a press-and-pull tipping primitive to recover object mass, center of mass height, and surface friction. The press-and-pull interaction increases the object-table sliding threshold and stabilizes the pivot, enabling controlled tipping without any prior geometric object model. Wrist force/torque sensing, RGB-D perception, and robot proprioception are fused to estimate the physical parameters from the two complementary interaction modes. Experiments on an ABB IRB120 across four objects with varied geometry, mass, center of mass, and friction achieve low relative error, while successfully operating on curved-base objects that fail under conventional forward tipping. The results demonstrate that complementary non-prehensile interactions can recover a compact set of physical parameters without grasping, a prior object model, or learned interaction dynamics.

0.23

Physics-Informed Tactile-based Shape Estimation of Deformable Linear Objects

cs.RO ·2026-11-17 ·Rotem Atari, Stav Ashur, Avishai Sintov
similarity 0.67
Abstract

Accurate shape estimation of Deformable Linear Objects (DLOs) is a fundamental challenge in robotic manipulation, often hindered by visual occlusions and the high-dimensional configuration space of flexible materials. While Force/Torque (F/T) and vision-centric methods have been proposed, they frequently struggle with grasp-site ambiguities and environmental interference. In this letter, we investigate the hypothesis that global shape estimation can be achieved through tactile sensing and proprioception, without any visual perception. We contend that dense, high-resolution tactile imprints capture critical boundary conditions and contact gradients that are sufficient to resolve the high-dimensional configuration of the DLO. To prove this, we introduce a Physics-Informed Vision Transformer (ViT) framework that maps tactile images to a 3D vertex chain. By leveraging self-attention mechanisms and a physics-weighted loss function, our model enforces structural priors to ensure that the predicted geometry adheres to the object's physical manifold. Experimental results demonstrate that our tactile-based approach achieves superior reconstruction accuracy across Euclidean and Chamfer metrics. Furthermore, we demonstrate the efficiency of this modality, achieving model transfer to novel DLO materials and geometries. Our findings suggest that tactile feedback provides a robust and computationally efficient alternative for DLO state estimation in visually degraded or occluded environments.

0.25

GLoTouch: Global-to-Local Haptic Perception Using a Parallel Gripper for Object Search, Recognition, and Grasping Without External Vision

cs.RO ·2026-09-23 ·Zonglin Li, Wanruo Zhang, Yiming Wang, Kun Song, Xinyi Zhou +1 more
similarity 0.66
Abstract

Perceiving objects in the environment is a fundamental capability of autonomous robots. In dark or low-light environments, external cameras often fail to reliably perceive object positions and geometry; when visual sensing is unavailable, completing target search, recognition, and grasping through touch alone becomes a key robot manipulation capability. This task must simultaneously address container-scale spatial exploration and object-scale fine-grained geometric perception, which is particularly challenging for low-degree-of-freedom parallel grippers. However, a unified framework remains lacking for connecting container-scale spatial exploration with object-scale fine-grained geometric perception and grasping. To address this challenge, we present \textbf{GLoTouch}, a global-to-local haptic perception and manipulation framework built on a parallel gripper. In the global stage, the gripper holds a passive long-reach probe, combining force measurements with known tool geometry to localize contacts and actively estimate candidate-object positions, coarse contours, and heights. In the local stage, the robot sets down the probe and uses the bilateral visuotactile sensors on the same gripper to directly acquire local haptic observations, which are matched against a given target 3-D model without object-specific training. We evaluate the framework in both simulation and real-robot experiments. Source code will be open-sourced.

0.30

How Firm Should a Grasp Be?

cs.RO cs.CV ·2026-10-08 ·Matthew Beveridge, Shree K. Nayar
dataset similarity 0.66
Abstract · CoRL 2026

An ideal robot grasp is firm enough to securely handle an object, yet gentle enough to avoid damaging it. Achieving this balance requires knowledge of the object's material properties, such as its mass, elasticity, and surface friction. These properties, however, are seldom precisely known a priori. In this work, we propose a visuotactile approach to estimating material properties in real time, during the process of grasping. Our method uses these estimated properties to determine the minimum grasp force required to handle the object. We contribute a new dataset of real-world objects (fruits and vegetables) with measured physical properties (shape, mass, elasticity, and friction), which we use to construct our force estimation model via simulations. We experimentally validate our approach to grasp force control using a robot with a parallel-jaw gripper. We demonstrate our system's ability to gently grasp a wide variety of objects, in each case adapting to their unique physical properties.

0.11

Force/Torque-Based Kinematic Adaptation for Robotic Manipulation Tasks

cs.RO ·2026-08-21 ·Carl Glen Henshaw
hot direction similarity 0.66
Abstract · 29 pages including appendices, 3 figures

Contact-rich robotic manipulation requires an accurate model of the kinematic relationship between a robot's joints and the task features it senses. This relationship is rarely known exactly: it changes with each tool the robot picks up and shifts, sometimes almost instantaneously, as contact modes change --- especially for multi-fingered hands that make and break contact at points that are not exactly prescribed, as in full-hand grasping. This paper develops an adaptive scheme that estimates that relationship online, using only joint-angle sensing and a wrist-mounted force/torque sensor, with no exteroceptive measurement of the tool tip. We derive a provably stable kinematic update law that identifies the kinematics of an unknown tool from force/torque feedback alone, and prove stability of both the rigid case and the case with a compliance controller as an inner loop. We show that identification is confined to the directions the motion excites --- so that, for example, a tool's length is unobservable under a rigid insertion push, while a compliant loop's passive yielding partially excites it; and that with a second-order admittance the compliant certificate holds unconditionally in continuous time. We also pose the combined control and estimation problem as a Quadratic Program (QP): the formulation yields the prediction term of the update law exactly but, instructively, cannot reproduce the tracking adaptation term. We validate the scheme in simulation on a peg-in-hole insertion. This work is the first step in a research program aimed at factoring manipulation learning into a task policy which can be learned in isolation of the robot, for instance by reinforcement learning, and an adaptive kinematic component that adapts online to the particular robot, hand, or tool in use.

0.29

Control Architecture for Safe Grasping of Fragile Objects Using a Coarse Position-Controlled Gripper

cs.RO ·2026-09-11 ·Marko Pavlic, Moritz Geier, Timo Markert, Darius Burschka
published similarity 0.65
Abstract · Accepted for IEEE IROS 2026 publication

Robots are increasingly used in unstructured environments. The need for them to safely grasp unknown objects without damaging them becomes crucial. Humans achieve this by sensing and quickly responding by adjusting their grasping force. Similarly, effective grasp acquisition in robots requires compliant interaction strategies that can adapt to uncertain object properties and adjust to any instabilities during manipulation. We present a geometry-aware force/torque-based contact estimation method for a coarse position-controlled gripper, combined with an adaptive admittance controller for safe grasp acquisition. The desired contact forces are estimated online to keep stable contact with objects of unknown properties. This enables compliant and stable grasps while avoiding excessive forces. Experiments with objects of different sizes, shapes, stiffnesses, and weights show that the proposed algorithm not only prevents slippage but also applies minimal force to safely grasp an object without causing excessive deformation.

0.28

TacSpin: Tactile Tracking of In-Gripper Object Rotation on SO(3) via Axis-Magnitude Estimation

cs.RO ·2026-10-13 ·Yuhao Wu, Linhao Song, Huan Yin
similarity 0.63
Abstract · 7 pages, 7 figures

Tracking object motion within a gripper provides essential feedback for robotic manipulation. However, limited contact coverage and uneven deformation make tactile estimation challenging. In this study, we present TacSpin, a method that tracks in-gripper object rotation on SO(3) using only two vision-based tactile sensors. The key idea is to estimate the axis and magnitude of the rotation response separately, rather than fitting a rigid-body model by least squares. Each finger's response is further refined with contact-boundary cues. The two fingers are then fused according to their agreement. On standard objects, TacSpin achieves lower mean checkpoint errors. Qualitative demonstrations on real-world objects, using calibration transferred from a standard sphere, illustrate tracking under different contact geometries.

0.14

PartialBiGrasp: Inferring Hidden Local Geometry for Bimanual Grasping from Partial Views

cs.RO ·2026-08-19 ·Ayush Kaura, Vignesh Vembar, Md Faizal Karim, Keshab Patra, K Madhava Krishna
similarity 0.61
Abstract

Dual-arm robotic grasping is essential for manipulating large, heavy, and geometrically complex objects that cannot be reliably handled using a single manipulator. These large objects often contain only sparse graspable regions determined by local geometric properties such as thickness, edge structure, and gripper clearance. Prior bimanual grasping methods assume access to a full point cloud of the object which inherently contains this geometric information, but may not be accessible in real scenarios. This work proposes PartialBiGrasp, a dual-arm grasp generation framework that operates directly on partial point cloud observations. Our model learns geometric features implicitly through convolutional occupancy networks, enabling local reasoning about graspability, collision-free contact regions, and object thickness. We leverage this understanding to generate force-closure compliant grasp pairs, which are further refined using a sampling-based optimization to correct for ambiguity caused by incomplete geometry. We evaluate our approach using analytical force-closure metrics, large-scale simulation experiments, and real-world robot evaluations on noisy partial point clouds of novel objects, demonstrating robust and physically stable dual-arm grasp generation.

0.16