CS Paper Radar

Aerial Non-Stop Trajectories Preserving the Equilibrium of Loads Suspended by Variable-Length Cables

Antonio Franchi, Alberto Landi, Chiara Gabellieri

eess.SY ·submitted 2026-09-11 14:48 UTC · v1

Abstract

This work studies equilibrium-preserving non-stop trajectories of aerial carriers connected to rigid loads by variable-length cables. Internal-force motions vary the cable directions without changing the load wrench, while cable-length actuation shapes the radial realization of the carrier trajectories. We derive an explicit cable-length law for realizing prescribed carrier-position profiles along a fixed direction, with constant altitude as a relevant specialization. Under this constraint, a carrier stops exactly when its cable direction stops changing. This characterization reveals a distinction between unrestricted and level motion: variable cable lengths enable bounded non-stop motion with two carriers, whereas periodic level non-stop motion is obstructed for two carriers and constructively achieved for three or more under explicit geometric and feasibility conditions. Numerical simulations illustrate the constant-altitude construction.

Closest papers

Nearest neighbours by meaning across the whole index.

Passive Stiffness Shaping in Cable-Suspended Aerial Manipulation via Movable Compliant Anchors

cs.RO cs.MAeess.SY ·2026-09-30 ·Antonio Franchi, Amr Afifi
similarity 0.69
Abstract

Cable-suspended aerial manipulation offers a lightweight architecture for cooperative transportation and physical interaction, yet the passive mechanical response perceived at the load remains insufficiently understood and systematically exploited. This work interprets aerial vehicles as movable compliant anchors and develops a gravity-aware quasi-static theory for predicting and shaping the passive Cartesian stiffness of a suspended load. The formulation applies to an arbitrary number of aerial vehicles connected to a point load by taut, straight, inextensible cables. At a selected gravity-loaded equilibrium, aerial-anchor compliance and transverse cable geometric compliance combine in series within each leg, while the leg stiffnesses act in parallel on the load. For isotropic aerial-anchor behavior, each leg is exactly equivalent to a virtual unilateral elastic cable, revealing an axial--transverse stiffness decomposition governed by the equilibrium tension. These results define a nonlinear map from commanded-anchor configuration to passive load stiffness, whose differential enables local constraint-preserving shaping through anchor repositioning. A dynamic rigid-body validation framework with nonlinear vehicle control, elastic-damped tendons, and environmental contact is defined to assess when and to what extent the derived stiffness remains predictive beyond the assumptions of the analytical model.

0.14

Cooperative Aerial Transportation of a Payload with a Sliding Cable Attachment

cs.RO cs.MA ·2026-10-09 ·Sebastian Tilaguy Lezama, Diego S D'Antonio
similarity 0.65
Abstract

This paper presents a dual-quadrotor hook- suspended transport system for cooperative aerial manipulation of a payload that is not rigidly attached to a fixed point along the cable. Two quadrotors are connected by a single inextensible cable that passes through a frictionless hook mounted on the payload, allowing the cable to slide between its two segments. This introduces a cable-distribution variable that couples the quadrotor motion, cable geometry, and payload dynamics. A feasible reference-generation framework is formulated using the desired payload pose, cable distribution, and system shape while satisfying the cable-length constraint and elliptical workspace. The quadrotors track the geometrically generated trajectories while maintaining positive cable tension and respecting actuator limits. The payload pose is estimated from the system geometry, and its measured position is used only to validate the desired trajectory. The approach is evaluated through experimental demonstrations.

0.33

Dynamics Modeling of a Multi-UAV Slung Load System Using a Discrete-Link Cable Approach

cs.RO ·2026-10-05 ·Harvey Merton, Ian W. Hunter
top venuecode/data similarity 0.60
Abstract · Presented at ICRA 2026 as an accepted paper

A common assumption to simplify the problem of controlling a multi-UAV slung load system (MUSLS) is that the flexible cables can be modeled as massless rigid rods. In this work, we propose an alternative Euler-Newton derived dynamical model which uses a series of rigid links to model the flexible cables. The model is specifically designed to allow efficient simulation using Featherstone's articulated body algorithm. We perform real-world validation of this model on gentle, aggressive, and tension-engagement maneuvers and run a parameter sweep to determine the number of links, joint damping, and joint friction to achieve the greatest model fidelity. The model closely matches real-world flight data with mean load translation errors below 132 mm (5.5% of the cable length) and orientation errors below 11.4 degrees. We make the real-world flight data publicly available for the development of future cable models.

0.54

AFD-CAMLs: Agile Force-Distribution-Aware Planning and Control for Cable-Suspended Aerial Multi-Lifting Systems

cs.RO ·2026-10-01 ·Antreas Kourris, Sihao Sun
similarity 0.59
Abstract · 9 pages, 11 figures

Multiple UAVs can cooperatively transport heavy payloads while controlling their position and orientation. Trajectory-based methods offer high agility while satisfying system constraints, but can produce uneven force distributions when the tension-to-wrench allocation is redundant or ill-conditioned, particularly under geometric mismatch and low-level tracking errors. We propose a hybrid planning-and-control framework to address this problem. A global planner generates payload trajectories and cable-force references by exploring the allocation null space under a prescribed internal-force setting. These references augment the cost of a centralized local planner, promoting feasible force distributions while generating trajectories for all UAVs. An admittance filter then compares the planned forces with onboard cable-tension estimates and adjusts the kinematic references to improve force tracking in degenerate or near-degenerate configurations. Simulations and experiments involving four to ten UAVs demonstrate more balanced tension distributions during both hovering and demanding agile maneuvers, without compromising agility or payload-tracking performance.

0.27

Compact Force Sensor for Dual-UAV Cable-Suspended Payload Transport with Tension-Aware Outer-Loop Control

cs.RO ·2026-09-25 ·Andrea Delbene, Giorgio Cannata, Giorgio Carlini, Filippo Sante, Marco Baglietto
top venue similarity 0.56
Abstract · Preprint version for IEEE Robotics and Automation Letters, link to article: https://ieeexplore.ieee.org/document/11743837

Cooperative payload transportation using multiple Unmanned Aerial Vehicles (UAVs) poses challenges in stability, coordination, and robustness, especially under external disturbances and unmodeled dynamics. This work proposes a dual-UAV payload transportation framework supported by a compact, custom-designed force sensor measuring the interaction force at the UAV cable anchor point. The sensor design and mathematical model are presented, and its performance is characterized through static and dynamic tests evaluating linearity, hysteresis, repeatability, and crossload. The control architecture follows a cascade structure: fast inner loops handle vehicle stabilization, while outer loops are designed to compensate for the measured forces. The approach is validated through simulations and indoor experiments under position uncertainty. Payload-drop and constrained-space tests assess the proposed sensing and control architecture against literature-based distributed references, showing improved stabilization, coordination, and disturbance rejection. A video of the experiments is available at: https://youtu.be/rIw9-fvV8Qw.

0.47

Payload Swing Estimation and Damping Without Payload Parameters for Multirotor UAVs

eess.SY cs.RO ·2026-08-19 ·K. Taki, K. Umemoto
similarity 0.54
Abstract

Cable-suspended payload transport by multirotor UAVs is flexible but generates periodic swing disturbance that degrades tracking and risks instability. Existing anti-swing methods require additional sensors or precise identification of cable length and payload mass, limiting field deployment. We propose a swing-estimation and damping method using only the onboard IMU and throttle command, requiring no payload parameters. An extended Kalman filter extracts the periodic disturbance with the unknown pendulum frequency as an estimated state, and an active damping controller adds a correction angle to the attitude loop to dissipate pendulum energy. Flight experiments confirm robust damping across a tested range of cable-length and mass variations.

0.21

Nonlinear Dynamic Modeling and Receding-Horizon NMPC of an Electric Unicycle on a Tensioned Cable

eess.SY ·2026-09-21 ·Yousef Sweiti, Jasem Tamimi
published similarity 0.54
Abstract

Traversing flexible slender structures involves strong bidirectional coupling between vehicle motion and structural vibration caused by a moving contact point. This paper presents a nonlinear modeling-and-control framework for an electric unicycle traversing a tensioned flexible cable. The cable is modeled using a tension-dominated finite-element formulation retaining vertical and lateral transverse dynamics, and is coupled to the unicycle roll and pitch dynamics through moving-contact kinematics. A modal truncation yields a control-oriented reduced-order model that preserves the nonlinear vehicle--cable coupling. Based on this model, a constrained nonlinear model predictive controller is formulated to regulate traversal, balance, actuator limits, and cable-span constraints. To reduce the computational burden associated with moving-contact interpolation, a frozen spatial contact-point interpolation strategy is introduced for the NMPC prediction model. Numerical studies under nominal, disturbed, constrained, and model-mismatch scenarios show accurate traversal, roll and pitch stabilization, attenuation of cable vibrations, and constraint-consistent closed-loop behavior. The frozen-interpolation formulation reduces and regularizes NMPC computation times relative to the non-frozen formulation, supporting its use as a computationally tractable approach for finite-element-based moving-contact vehicle--structure interaction systems.

0.38

Catenary Visibility: A Geometric Framework for Planning with Tethered Robots

cs.CG cs.RO ·2026-10-30 ·B. Ábrego, J. M. Díaz-Báñez, S. Fernández, D. Flores-Peñaloza, V. Sánchez-Canales
similarity 0.52
Abstract · 23 pages, 13 figures

This paper introduces \emph{catenary visibility}, a new geometric visibility concept for a robotic system consisting of a ground robot tethered to an aerial drone. The tether is modeled as an extensible catenary curve with bounded length, providing sustained power and significantly extending operational range. We define a point on the ground plane as \emph{catenary-visible} from a target point in 3D if there exists a collision-free catenary connecting them, given a set of obstacles. This paper introduces a geometric framework for visibility-aware planning of a tethered marsupial system, addressing the computational challenge of determining the feasible deployment locus: the collection of points in the ground plane that are catenary-visible from a given target in 3D space. We begin by solving the 2D subproblem, where the obstacles, target, and the ground vehicle's line of motion are all constrained to a single vertical plane. Our algorithm for this case computes the complete set of feasible launch points along the motion line and simultaneously determines the range of viable cable lengths for each. We also consider the query problem of finding all collision-free length ranges for a given location of the ground robot. Building upon this planar solution, we then generalize the approach to three dimensions, deriving a 3D solution for a constrained class of obstacles.

0.36